Sony BKP-7933 - Manuals

Sony BKP-7933 – Manual in PDF format online.

Manuals:

Manual

Manual Sony BKP-7933

Summary

Page 3 - Table of Contents; Manual Structure; Linking the MSU Camera Selection

1 (E) BKP-7933 Table of Contents Manual Structure Purpose of this manual ........................................................................................ 3 (E) Related manuals ................................................................................................... 3 (E) Trademarks...

Page 7 - ROM Version; The BKP-7933 is composed of the following items.; Installation procedure; Checking ROM Version

1-1 (E) BKP-7933 Section 1 Installation 1-1. Checking ROM Version When the BKP-7933 is installed in the CNU-700, be sure to check that the ROM versions for IC4 and IC5/AT-89 board of the CNU-700 are Ver. 3.00 or higher. If the ROM needs to be replaced, contact your local Sony Sales Office/Service Ce...

Page 8 - OFF; Setting of CNU GROUP No.; Set the CNU GROUP No. so that it should be unique in a system.; Setting Examples; When using the two CNU-700s which are provided with the BKP-7930; Set CNU GROUP No. to 2

1-2 (E) BKP-7933 1-4. Setting Switches on the IF-689 Board m. Be sure make the switches settings for the CNU GROUP No. and S-BUS ID No. before turning on thepower. It is no use in setting the switches after turning on the power. . Do not change the following switches from their factory default setti...

Page 9 - Setting example; Set the station address for the unit on the standard S-BUS data link.; IF

1-3 (E) BKP-7933 1 8 7 6 5 4 3 2 1 ( ) 128 64 32 16 8 4 2 S-BUS ID No. Setting example 1 3: 0 0 0 0 0 0 1 0 64: 0 1 0 0 0 0 0 1(ON) 0(OFF) Setting of S-BUS ID No. S12 (S-BUS ID No.) Set the station address for the unit on the standard S-BUS data link. n Set to numbers other than 0, 1 and 255. Factor...

Page 10 - Screw

1-4 (E) BKP-7933 1-5. Installation 1-5-1. Installing the IF-689 Board n The unit is equipped with shielding springs which have sharp edges. Do not touch them with bare hands. Pay careful attention when servicing. 1. Loosen the two screws and remove the front panel of the CNU-700. 2. Insert the IF-68...

Page 11 - Remove the two screws and remove the blank panel.; Blank panel

1-5 (E) BKP-7933 1-5-2. Installing the Rear Panel 1. Remove the two screws and remove the blank panel. 2. Install the rear panel with the two screws instead of the blank panel. B3 x 5 B3 x 5 Blank panel Rear panel 1-5. Installation

Page 17 - ROUTER; Saving the Setup Data; Press; Level Mapping

1-11 (E) BKP-7933 12131415 1 1 12 33 33 44 44 45 45 56 56 57 57 58 68 1024 1024 ROUTER PIX1 CAMERA-CCU CCU-RCP MSU2 MSU1 SOURCE No. DESTINATION No. LEVEL-1 ROUTER PIX3ROUTER PIX2(MSU2)ROUTER PIX2(MSU1) Saving the Setup Data Press [Ctrl] - [E] to validate and save the setup data and to return to the ...

Page 18 - Description of Operation; corresponds to the RCP is automatically switched at the same time.

1-12 (E) BKP-7933 1-7-2. Linking the RCP Assignment and VE Monitor Selection Description of Operation Set the menu as follows when you want to link the RCP assignment with the VE monitor selection.If this setting is executed, by changing the RCP assignment on the MSU side, the VE monitor that corres...

Page 19 - Connecting Peripheral Equipment

1-13 (E) BKP-7933 CCA-5 CABLE CCA-5 CABLE REMOTERCP/CNU REMOTECCU/CNU REMOTECCU/CNU REMOTECCU/CNU REMOTECCU/CNU CCU 1 to 6 RCP 1 to 6 MSU IN 1 OUT 1OUT 2 OUT 6 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2 IN 6 SERIALOUTPUT REMOTERCP/CNU SERIALOUTPUT SERIALOUTPUT REMOTERCP/CNU DIGITALROUTING SWITCHERDVS-V1616...

Page 20 - Setting from the S-BUS Primary Station

1-14 (E) BKP-7933 Setting from the S-BUS Primary Station 1. Select the menu item “Z:BKP-7933 CONFIGURA- TION” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2 MODIFICATION COMMAND A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNIT LOCATION(MSU) ...

Page 21 - -7-3. Linking the MSU Camera Selection and the VE Monitor Selection; Digital Video Routing Switcher

1-15 (E) BKP-7933 1-7-3. Linking the MSU Camera Selection and the VE Monitor Selection Description of Operation Set the menu as follows when you want to link the MSU camera selection with the VE monitor selection.If this setting is executed, when the MSU camera select button is pressed, the video si...

Page 22 - VIDEO BNC; PIX

1-16 (E) BKP-7933 * If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX or WF connector (PIX 2 or WF 2 connector for the CCU-700A series) CCA-5 CABLE CCA-5 CABLE REMOTERCP/CNU REMOTECCU/CNU CCU 1 to 6 MSU IN 1 OUT 13 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2 IN 6 SERIALOUTPUT REMOTERC...

Page 24 - Switch

1-18 (E) BKP-7933 * If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector CCA-5 CABLE CCA-5 CABLE REMOTERCP/CNU REMOTECCU/CNU REMOTECCU/CNU REMOTECCU/CNU REMOTECCU/CNU CCU 1 to 6 RCP 1 to 6 MSU IN 1 OUT 15 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2 IN 6 IN 13 SERIALO...

Page 26 - Linking the Preview Monitor Selection with MSU and VCS

1-20 (E) BKP-7933 Linking the Preview Monitor Selection with MSU and VCS 1. Select the menu item “Z:BKP-7933 CONFIGURA- TION” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2 MODIFICATION COMMAND A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UNI...

Page 27 - Changing the Operation Mode of the RCP PREVIEW Switch; Use the switches on the AT board inside the CNU-700 for this setting.

1-21 (E) BKP-7933 Changing the Operation Mode of the RCP PREVIEW Switch The operation mode of the RCP PREVIEW switch can be changed on the CNU-700 character display. Use the switches on the AT board inside the CNU-700 for this setting. 1. Set the MODE switch to 5.The message “INTERNAL MODE SETTING” ...

Page 28 - -7-5. Executing RCP Assignment from Equipment Other Than MSU; 6 CCU-RCP matrix can be set in the matrix space of; shows an area where the SOUCE No. and DESTINATION No. cannot be set.

1-22 (E) BKP-7933 1-7-5. Executing RCP Assignment from Equipment Other Than MSU Description of Operation Set the menu as follows when you want to execute RCP assignment from equipment other than MSU.When this setting is executed, a maximum of 96 x 96 CCU-RCP matrix can be set in the matrix space of ...

Page 34 - Displaying the SOURCE NAME on the CNU Character Display; TION” and press

1-28 (E) BKP-7933 Displaying the SOURCE NAME on the CNU Character Display 1. Select the menu item “Z:BKP-7933 CONFIGURA- TION” and press [ENTER] . SONY ROUTING SYSTEM SETUP MENU BKP-7933 V1.00 STATION NUMBER 2 MODIFICATION COMMAND A: SET UNIT LOCATION(CAM-CCU) B: SET UNIT LOCATION(CCU-RCP) C: SET UN...

Page 35 - of the tally system may become slower.

1-29 (E) BKP-7933 1-7-8. Using the Tally System Description of Operation Set the menu as follows when you want to construct a tally system using the S-BUS. When this setting isexecuted, the red tally and the green tally signals are accepted through the S-BUS and are output to the corresponding CCU a...

Page 39 - Default Values

1-33 (E) BKP-7933 1-7-10. Returning the Setups of the MODIFICATION COMMAND to the Factory Default Values 1. Select “K: RESET TO DEFAULT TABLE” using thecursor key and press [ENTER] . 2. The message “Reset to Default table?” appears in the bottom right of the screen. Select “Y” and press [ENTER] . SO...

Page 40 - Example of Controlling 13 or More Cameras

1-34 (E) BKP-7933 * If using the ANALOG ROUTING SWITCHER (BVS-V3232 etc.), connect it to PIX, WF or VBS connector CCA-5 CABLE CCA-5 CABLE CCA-5 CABLE REMOTERCP/CNU REMOTECCU/CNU CCU 1 to 12 MSU AUX 1 AUX 1 IN 1 OUT 25 REMOTE 1 REMOTE S-BUS REMOTE 3 IN 2IN 12IN 13 IN 24 IN 14 SERIALOUTPUT REMOTERCP/C...

Page 41 - Message displayed automatically by a program; Type as follows. The BZR-10 software is installed to the hard disk.; cd; Remove the FD from the disk drive.

1-35 (E) BKP-7933 1-8. Data Backup/Restore m. The description in this section assumes that BKPF-R70 is used as the primary station. . The setup data of the unit is backed up and restored by using the BZR-10 (software for data backup) supplied with the BKPF-R70. . In this section, a lower-case letter...

Page 43 - Function Menu

1-37 (E) BKP-7933 13. Type “1” at the Function menu. (“1. RECEIVE” is selected.) The display changes to the Execution menu screen. 14. To back up the data of the BKP-7933, type “2”. (“2. The data of secondary stations” is selected.) The data is backed up in the FD. 15. Type “9” twice. (“9. Quit” is ...

Page 45 - board in the RCP are required.; Description; Jumper wire; Cut the printed foil pattern between Q35 emitter and Q34 emitter. (; Setting Switch on MPU-92 Board; ON

1-39 (E) BKP-7933 1-9. Modification of RCP The video on the preview monitor can be selected by the PREVIEW switch of the RCP-700/701/720/721/ 730/731. (Refer to section 1-7-4 for details.)However, version check of the ROM that is installed in the board of the RCP side, and modification of the board ...

Page 47 - Required Part; Modification Procedure

1-41 (E) BKP-7933 1-9-3. Modification of RCP-720 Required Part Description Sony P/N Q'ty Jumper wire _ _ Modification Procedure 1. Connect the two jumper wires by soldering. (SW-754 board) Between pin-6/CN3 and D25 cathode ( 1 ) Between pin-5/CN3 and pin-2/S24 ( 2 ) 2. Disconnect CN101/CN-1187 board...

Page 48 - Required Parts; Resistor, Chip Metal 82; Connect a metal resistor 82

1-42 (E) BKP-7933 1-9-4. Modification of RCP-721 Required Parts Description Sony P/N Q'ty Resistor, Chip Metal 82 Z 1-216-625-11 1 Jumper wire _ _ Modification Procedure (SW-752 Board) 1. Remove the resistors R10 and R55/SW-755 board. 2. Connect a metal resistor 82 Z to the soldering land of R10, by...

Page 49 - Resistor, Chip Metal 0; Connect metal resistors 0

1-43 (E) BKP-7933 1-9-5. Modification of RCP-730/731 Required Parts Description Sony P/N Q'ty Resistor, Chip Metal 0 Z 1-216-295-11 3 Resistor, Chip Metal 82 Z 1-216-625-11 1 Modification Procedure (SW-893 Board) 1. Remove soldering of R1, R2, R3 and R12. 2. Connect metal resistors 0 Z to the solder...

Page 51 - Modification of AT-89 Board; RS-422 harness that is supplied, instead of the removed harness.; ROM Replacement of the MSU-700; Assignment” for the setting procedure.; Rear panel

1-45 (E) BKP-7933 Modification of AT-89 Board 1. Connect a jumper wire between B7 pin/CN2 and B9 pin/CN2 of the AT-89 board of the CNU-700 by soldering. 2. Remove the six screws and remove the rear panel. Remove the harness that is connected to theconnector CN12 on the MB-562 board and the connector...

Page 54 - Green

1-48 (E) BKP-7933 1-11. Description on Internal Indicators Ref.No. Indicator Name Color Status D1 + 5 V Green Lights when +5 V is normally supplied to the IF-689 board D402 S-BUS RX Green Lights when the serial data is received from the REMOTE S-BUS connector D403 S-BUS TX Green Lights when the seri...

Page 56 - Printed in Japan; Sony Corporation; Communication System Solutions Network Company