SoleusAir PH3-10R-03- Manuals

Page 3 - MODEL

3 SPECIFICATIONS • The cooling capacity is measured at an ambient temperature of DB 86 °F, WB 78 °F. • Noise level is measured at a distance of 3.28 ft away from the front of the unit, when the unit is in cooling mode. • Power consumption is measured when the fan runs at the highest speed setting. •...

Page 4 - PRODUCT DIAGRAM; (Actual product design may differ slightly from images below)

4 PRODUCT DIAGRAM (Actual product design may differ slightly from images below) FRONT A. Control panel B. Vertical air louvers C. Air outlet D. Horizontal air louvers E. Casters F. Power Cord & Plug BACK A. Hot air outlet grill B. Lower air inlet grill ACCESSORIES Flexible exhaust hose with 2 ad...

Page 5 - INSTALLATION

5 INSTALLATION SELECTING THE LOCATION Place the unit in a flat location where the air out-lets are not obstructed. Place the unit at least 20” (50cm) away from a wall or other obstacle. MOUNTING THE EXHAUST HOSE Slide the square end of the exhaust duct over the hot air outlet on the back of the unit...

Page 6 - LCDI POWER CORD AND PLUG; The TEST and RESET buttons should not be used as

6 LCDI POWER CORD AND PLUG This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord with no termination on the load side and a LCDI attachme...

Page 7 - WINDOW KIT INSTALLATION

7 WINDOW KIT INSTALLATION The window kit is designed to fit into most standard vertical and horizontal windows, as well as some sliding glass doors. However, it may be necessary to modify some aspects of the installation process for certain window types. Open the window or sliding door and adjust th...

Page 10 - CONTROL PANEL BUTTONS (Refer to the images on page 9)

10 OPERATING INSTRUCTIONS CONTROL PANEL BUTTONS (Refer to the images on page 9) 1) Power On and Off - Press the POWER button once to manually turn the unit on. Press the POWER button once more to turn the unit off. 2) Mode Selection - Press the MODE Button repeatedly to cycle between the different m...

Page 12 - Sleep Mode

12 NOTE: It is not necessary for the exhaust hoses and window kit to be installed to operate the unit in fan mode. Heat Mode 1) Install the exhaust hoses and window kit properly (see pages 7 & 8). 2) Plug the power cord into a grounded outlet. 3) Turn on the unit by pressing the On/Off button on...

Page 13 - When the water container is full, the unit will display ‘

13 Compressor Indicator The “ ” icon will light up on the control panel display when the compressor turns on. The “ ” icon will turn off when the compressor shuts off. Emergency Condensate Holding Tank When the unit is in cooling mode, unwanted water is extracted from the air. Most of this water is ...

Page 14 - OPERATING THE UNIT USING THE REMOTE CONTROL

14 REMOTE CONTROL TIMER/TEMP INCREASE FAN SPEED POWER BUTTON TIMER BUTTON TIMER/TEMP DECREASE SLEEP MODE MODE BUTTON FAN SPEED SWING (LOUVER OSCILLATION) OPERATING THE UNIT USING THE REMOTE CONTROL REMOTE CONTROL OPERATING INSTRUCTIONS 1) Power On and Off - Press the ON/OFF button on the remote to t...

Page 15 - MAINTENANCE; and dry it thoroughly out of sunlight.

15 MAINTENANCE Note: Make sure power is off and the power cord is not plugged into an electrical outlet prior to performing any maintenance on the unit. Clean or replace filter - If the air filter is blocked with a dust, the airflow volume may reduce. It is recommended to clean the filter once every...

Page 16 - WARRANTY; THIS WARRANTY DOES NOT COVER:

16 WARRANTY One Year Limited Warranty Soleus International Inc. warrants the accompanying Soleus Air PH3-09R-03 / PH3-10R-03 Portable Air Conditioner with Heat Pump technology to be free of defects in material and workmanship for the applications specified in its op-eration instruction for a period ...