SoleusAir HI1-50-03- Manuals

Page 4 - chemical storage areas.; SAFETY INFORMATION

1. Use Copper wire only rated at least 60°C (140°F) 2. For supply connections use No.10 AWG or larger wires suitable for at least 60°C (140°F) 3. Heater air flow must be directed parallel to, or away from, adjacent walls. 4. Observe wall, floor, and ceiling clearance requirements on DIAGRAM 1 on Pag...

Page 5 - HEATER LOCATION AND INSTALLATION; FRONT VIEW; DIAGRAM 1

HEATER LOCATION AND INSTALLATION Install the heater out of traffic areas maintaining the required clearances below. The direction of air flow shold not be restricted by anything and the air flow should not blow directly at exposed walls. When more than one heater is used in an area, the heaters shou...

Page 6 - SPECIFICATIONS

SPECIFICATIONS Voltage Rating / Amps 208/240 V / 21 Amps / Single Phase Power Consumption 5000 Watts Unit Size 15.7 in. (W) x 11.29 in. (D) x 14.37 in. (H) Unit Weight 27.00 lbs. Fan CFM 270 CFM Heating BTU’s 17,100 6 www.sylvane.com 1-800-934-9194

Page 7 - MOUNTING THE BRACKET; wrench and slipping the handle off over the screw heads.; NOTE; : If you want the heater to swivel side to side,; HANGING THE HEATER; Lift the heater up and into the mounting bracket.; SINGLE –SCREW MOUNTING

LOCATION AND INSTALLATION (CONT.) MOUNTING THE BRACKET 1. Locate a stud in the ceiling joist. 2. Remove the mounting bracket from the heating unit be loosening the bracket screws with a wrench and slipping the handle off over the screw heads. 3. Place a washer on the screws before inserting through ...

Page 8 - CONNECTING THE POWER; Turn off the power at the main service; Turn on the power at the main service.; OPERATION

LOCATION AND INSTALLATION (CONT.) CONNECTING THE POWER 1. Turn off the power at the main service 2. Remove the screw from the back of the unit to connect the power to the heater. 3. Attach the cable connectors to the unit and slide the 10 gauge wire through the cable connector. NOTE : For certain ap...

Page 9 - ADJUSTING THE AIR FLOW DIRECTION; as needed to adjust the direction of the air flow.; : To tilt the heater it must be mounted in bottom keyhole slots of; : The louvers are designed so they cannot be

OPERATION (CONT.) ADJUSTING THE AIR FLOW DIRECTION 1. Rotating the unit - if the unit has been installed with a single lag bolt, simply rotate the entire unit as needed to adjust the direction of the air flow. 2. Tilting the unit - Loosen the bracket screws, tilt the heater to the desired position, ...

Page 10 - WIRING DIAGRAM

OPERATION (CONT.) WIRING DIAGRAM 1. It is recommended that #10 AWG wire be used in all installations for possible future reconnection at a higher wattage (Refer to the National Electric Code (NEC) for maximum run length to mini-mize voltage drop to 3% max. Circuit runs exceed 100 ft. may require lar...

Page 11 - MAINTENANCE; CLEANING THE FAN AND MOTOR

MAINTENANCE To prevent possible electric shock, disconnect the power to the heater at the main service box be-fore attempting inspect or clean the unit. Use care to prevent damage to the internal components of the heater when cleaning the heating element. Make sure all connections remain tight and a...

Page 12 - WARRANTY; THIS WARRANTY DOES NOT COVER:; Freight and Insurance cost for the warranty service.; For Technical Support or Warranty Service

WARRANTY One Year Limited Warranty Soleus International Inc. warrants the accompanying Soleus Air Heater to be free of defects in material and workman-ship for the applications specified in its operation instruction for a period of ONE (1) year from the date of original re-tail purchase in the Unite...