Snapper CZT19481KWV - Manuals

5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5SECTION 1 - FAMILIARIZATION . . . . . . . . . . . . . ...

6 Section 1 - FAMILIARIZATION IMPORTANT The figures and illustrations in this manualare provided for reference only and maydiffer from your specific model. Contactyour Snapper dealer if you have questions. FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operators of theSNAPPER COMM...

7 Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTS PARKING BRAKE LEVER OPERATION MOTION CONTROL LEVER OPERATION WEAR HEARING PROTECTION WARNING ! AVOID SERIOUS INJURY OR DEATH

11 Section 3 - OPERATING INSTRUCTIONS Section 3 - OPERATING INSTRUCTIONS ROLL RELEASE: To roll the machine without theengine running, pressure within the hydraulic pumpsmust be released. There is a hydraulic pressure reliefvalve on the upper side of each pump that is used torelease the pressure. Use...

13 Section 3 - OPERATING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever. IMPORTANT: There is a footassist pedal located to the right front side of thefootrest. Always use this assist pedal to raise or lowerthe deck to the desir...

14 Section 3 - OPERATING INSTRUCTIONS 3.4.2. STOPPING MACHINE1. Return motion control levers to the neutral position & the neutral lock position. IMPORTANT: Operator must use hand assistance to bring both motion control levers to the neutral position& the neutral lock position. 2. Engage par...

16 Section 3 - OPERATING INSTRUCTIONS Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BELT1. Lower deck to lowest setting. 2. Remove footrest. See Figure 4.3. 3. Removal of footrest will allow access to mower drive belt. 4. Check the belt tension. If belt is frayed, slit, sev- ered or belt strands ...

17 Section 3 - OPERATING INSTRUCTIONS Section 4 - MAINTENANCE 4.3.3. RIDING MOWER - LUBRICATION1. Front Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease orequivalent, from a grease gun. See Figure 4.5. 2. Hydro Pumps Check the level of the fluid in the fluid reservoir. Wipeaway all di...

20 Section 3 - OPERATING INSTRUCTIONS Section 5 - ADJUSTMENTS & REPAIR 5.1 NEUTRAL POSITION ADJUSTMENTS The motion control levers control the movement andstopping of the machine. Move the control levers to thecenter or neutral position to stop machine. IMPORTANT: Always return both motion contro...

22 Section 3 - OPERATING INSTRUCTIONS Section 5 - ADJUSTMENTS & REPAIR 5.2.1. MOWER DECK ADJUSTMENT (LEVELNESS)SIDE to SIDE and FRONT to REAR 8. Move deck lift lever and set the mower deck to the highest cutting position and recheck side to side bladetip dimensions. The difference between the tw...

23 Section 3 - OPERATING INSTRUCTIONS Section 5 - ADJUSTMENTS & REPAIR 5.3 TRACTION BELT TENSION The traction drive belt tension does not require adjustment.If the belt is slipping, it will have to be replaced. 5.4 TRACTION BELT REPLACEMENT 1. Remove mower drive belt from around clutch pul- ley....

24 Section 3 - OPERATING INSTRUCTIONS Section 5 - ADJUSTMENTS & REPAIR 5.6a MOTION LEVER HANDLEBAR ALIGNMENT Handlebars of both left and right Motion ControlLevers should be aligned when levers are droppedfrom their neutral lock positions. See Figure 5.12a. Ifbars are not aligned: 1. Loosen bolt...

25 Section 3 - OPERATING INSTRUCTIONS Section 5 - ADJUSTMENTS & REPAIR 5.8 ENGINE ADJUSTMENTS & REPAIR Refer to the engine owner's manual for engine adjust-ments and/or repairs. 5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS1. Inspect blade frequently for signs of excessive wear or dam...

27 Section 3 - OPERATING INSTRUCTIONS Section 5 - ADJUSTMENTS & REPAIR 5.10.4. BATTERY TESTING1. Remove battery. Refer to Section "BATTERY REMOVAL". 2. Using a voltmeter, check the battery's state of charge by comparing the voltmeter reading with thechart below. (Remember to hook the pos...

29 Section 3 - OPERATING INSTRUCTIONS TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank Engine 1. Battery dead. 1. Service battery. 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Clean and check connections for good contact. 4. Defective...

37 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following information on your Snapper purchase) Model Number_________________________________________________________ Serial Number _________________________________________________________ ...