Snapper 8526, 9528, 10530, 11532 - Manuals

D e c a l s 6 DECALS This unit has been designed and manufactured to pro-vide you with the safety and reliability you would expectfrom an industry leader in outdoor power equipment. Although reading this manual and safety instructions itcontains will provide you with the necessary basic knowl-edge t...

D e c a l s 7 Part No. 1733059 - DANGER / WARNING Main Dash Decal, CE, w/o Easy Turn Part No. 1733060 - DANGER / WARNING Main Dash Decal, CE, w/ Easy Turn Part No. 1732618Shift Decal Part No. 1727208Auger Danger Decal Part No. 1727207Discharge ChuteDanger Decal Part No. 1733443Chute Release ALL MODE...

S a f e t y I c o n s 8 WARNING: READ OPERATOR’SMANUAL. Read and understand the Operator’sManual before using this machine. DANGER: THROWN OBJECTS. This machine is capable of throwingobjects and debris. Keep bystandersaway. WARNING: REMOVE KEY BEFORESERVICING. Remove the key, disconnect sparkplug wi...

I d e n t i f i c a t i o n N u m b e r s 9 When contacting your authorized dealer for replace-ment parts, service, or information you MUST havethese numbers. Record your model name/number, manufacturer’s identi-fication numbers, and engine serial numbers in thespace provided for easy access. These ...

10 Features, Controls, & Operation CONTROL LOCATIONS The information below briefly describes the function of individual controls. Starting, stopping, and driving require thecombined use of several controls applied in specific sequences. To learn what combination and sequence of controlsto use fo...

F e a t u r e s & C o n t r o l s 11 Fuel Fuel tank filler cap (see illustration). Note: The fuel shutoff valve is located under the fuel tank or on the front ofthe engine. Close the valve when the snowthrower is notin use. Open the valve before starting. Primer Button When pressed, the primer b...

O p e r a t i o n 12 GENERAL OPERATION CHECKS BEFORE EACH START-UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out is attached to the auger housing. Do not operate the machine with-out the clean-out tool properly stored o...

O p e r a t i o n 13 STARTING CONTROLS See Figure 1 for the following instructions. Electric Start A. Electric Start Button - The Electric Start Button (A) activates an electric starter mounted to theengine, eliminating the need to pull the starter han-dle. The Electric Start Button operates on 120 ...

O p e r a t i o n 14 5. When BOTH levers are depressed, the Free-Hand™ Control is activated. This allows Auger EngageControl to be released — YET AUGER ROTATION WILL CONTINUE — until the Free-Hand™ Controlis released. 6. Select forward or reverse speeds as needed using the Speed Selector (A, Figure ...

O p e r a t i o n 15 GROUND SPEED SELECTOR Use the speed selector (A, Figure 2) to control the drivespeed of the snowthrower. There are five forward speedsand two reverse speeds. Use the lower speeds to blow deep or wet snow. Use thehigher speeds to blow light snow or to drive the snow-thrower witho...

O p e r a t i o n 16 EASY TURN™ FREEWHEELING AND TRACTION DRIVE LOCK While Clearing Snow: For easy turning when using the snowthrower, squeezethe Easy Turn™ lever (Figure 5). Engaging the EasyTurn™ lever releases the left traction wheel but allowsthe right wheel to continue driving (Figure 5). Relea...

O p e r a t i o n 17 AFTER EACH USE Normal use of the snowthrower may result in a build-upof packed snow in and around the starter cord housingand around engine controls. Heat from the engine willusually prevent the snow from freezing solid while theunit is running, but after the engine is shut down...

18 Regular Maintenance AUGER GEAR CASE LUBRICATION 1. Place the snowthrower on a level surface. 2. Remove the pipe plug (A, Figure 8). 3. Check the lubricant level. It should be level with the lower edge of the plug opening. If not, add Lithiumgrease. 4. Re-install pipe plug, and tighten securely. F...

LUBRICATION Remove wheels and grease axles once each year. Apply 5W-30 synthetic motor oil to the friction disk drivehex shaft (A, Figure 10). Apply medium weight (10W) oil to points shown (SeeFigures 9-12). Generally, all moving metal parts should be oiled wherecontact is made with other parts. Kee...

22 Troubleshooting, Adjustments, Service WARNING Before performing any adjustment or service tosnowthrower, stop the engine and wait formoving parts to stop. Remove the key. To preventaccidental starting, disconnect the spark plugwire and fasten away from the plug. PROBLEM POSSIBLE CAUSE REMEDY Engi...

Tr o u b l e s h o o t i n g 23 PROBLEM POSSIBLE CAUSE REMEDY Auger rotates, but snow is not thrown far enough 1. Chute deflector too low. 1. Adjust deflector as necessary. 2. Engine speed too slow. 2. Set speed to full throttle. 3. Ground speed too fast. 3. Use slower speed selector setting. 4. Sno...

A d j u s t m e n t s 24 AUGER DRIVE ADJUSTMENT 1. Check that the auger cable (A, Figure 15) is on top of cable button (B) as show in Figure 15. 2. With the drive lever released, the hook (B, Figure 16b) should barely touch the lever (C) without raisingit. There can be a maximum 1/32” clearance assh...

A d j u s t m e n t s 26 Figure 20. Cable AdjustmentA. Adjustment NutB. Jam Nut A B Figure 21. Belt CoverA. Belt CoverB. Screws A B B Figure 22. Auger Belt DeflectionA. Engine Drive PulleyB. Idler Pulley (Engaged Position)C. Auger Drive PulleyD. NutE. Auger Belt B C A 1/2” (12.5mm)Deflection EASY TU...

A d j u s t m e n t s & S e r v i c e 27 Figure 23. Shear PinsA. Shear PinsB. Cotter Pins A B A B SHEAR PIN REPLACEMENT Under most circumstances, if the auger strikes an objectwhich could cause damage to the unit, the shear pin willbreak. (This protects the gear box and other parts fromdamage.) ...

S e r v i c e 28 BELT REPLACEMENT Auger Drive Belt The drive belts are of special construction and must bereplaced with original factory replacement belts availablefrom your nearest authorized service center. Somesteps require the assistance of a second person. If theauger drive belt is damaged, the...

Specifications 31 ENGINE: 8.5 HP* Briggs & Stratton Make Briggs & Stratton Model Power Built Horsepower 8.5 @ 3600 rpm Displacement 15.2 Cu. in (249 cc) Oil Capacity 19 oz. (,56 L) 9.5 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Snow Horsepower 9.5 @ 3600 rpm Displacemen...