Snapper 1723846 - Manuals - manualsarea.com

Page 2 - Table of Contents

1 Catcher Assembly - All Models Assemble Supports & Hitch .............................5Install Cover & Bags ........................................6Assemble & Install Tubes ................................6 Normal Removal & Installation Removal.........................................

Page 3 - SAFETY DECALS; GENERAL WARNINGS; ATTACHMENT DECALS

2 Safety Rules& Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian-gle in text signifies important cautions or warnin...

Page 4 - General; REQUIRED ACCESSORIES; STORING THE GRASS CATCHER; CAUTION

3 BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagging, air circulation under them...

Page 6 - Initial Assembly & Installation; CATCHER ASSEMBLY - ALL MODELS; Assemble Supports and Hitch

5 Initial Assembly & Installation Figure 5. Assemble Catcher FrameA. Upright Support C. Horizontal Support B. 3/8-16 x 7/8 Capscrew D. 3/8-16 Whizlock Nut A B C D Figure 6. Assemble Catcher Frame (Prestige Shown)A. 3/8-16 Nut & Lockwasher C. 3/8-16 x 1 CapscrewsB. Upright Support Assy. D. Lo...

Page 7 - Install Cover and Bags

6 Initial Assembly & Installation Figure 8. Install Catcher (Prestige Shown)A. #10-32 Nut F. Bags B. Handle G. Hair Pin Clip C. #10-32 x 1/2 Screw H. Catcher Hitch D. Cover I. Spacers E. Hinge Pin Figure 9. Install CableA. Cable C. Washer B. Support I A B C D E F H G Install Cover and Bags 1. Mo...

Page 8 - NORMAL REMOVAL & INSTALLATION; Removal; Installation

7 Normal Removal & Installation WARNING OPERATION WITHOUT TURBO & CATCHER For operation without turbo, the mower deflectorMUST be properly installed in the down position andretained by the spring latch (see turbo operator’smanual). Figure 11. Normal Removal & Installation (Prestige Shown...

Page 9 - Installation with a Tiller; INSTALLATION WITH A TILLER; Initial Setup

8 Installation with a Tiller INSTALLATION WITH A TILLER Initial Setup Note: Use the short upright bracket (refer to Figure 4). 1. Assemble the lower support (E, Figure 12), spacers (D), and plate (C) as shown). 2. Bolt the lower plate assembly (E) to the upright sup- port (I) using four 3/8-16 x 3/4...

Page 10 - Notes

Page 11 - Torque Specification Chart; Hardware Identification & Torque Specifications; Wrench & Fastener Size Guide

Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7....

Snapper 1723846 - Manuals

Manuals:

Manual Snapper 1723846

Summary

Snapper Manuals