Page 3 - Table of Contents
1 Safety Rules & Information General Warnings ............................................2 Safety Decals ..................................................2 General Operating Instructions Before Operation .............................................3 Mowing with the Catcher ......................
Page 4 - SAFETY DECALS; GENERAL WARNINGS; Attachment Decal; WARNING
2 Safety Rules& Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, severe personal injury or death to you, or bystanders, or damage to property or equipment. Thetriangle in text signifies important cautions or warnings...
Page 5 - General; After Operation; CAUTION
Before Operation Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagging, air circulation under themow...
Page 6 - Initial Installation; Hitch Installation
InitialInstallation 4 Before beginning any service work turn off thePTO, set the parking brake, turn off the ignition,and disconnect the spark plug wire(s). WARNING Figure 1. Install Spacer (left side shown)A. Speed Nut, 5/16-18B. Threaded SideC. Square HoleD. Shoulder Bolt, 5/16-18E. Rear Frame Sup...
Page 7 - Baffle Installation
5 Baffle Installation Baffle and Blade Installation Note: Units with an anti-blowout baffle do not require theClean Sweep baffle. 1. Remove mower deck. See OPERATOR’S MANUAL. 2. Install notched side of baffle (A, Figure 3) to discharge side of deck securing with 5/16-18 x 2carriage bolt (C) and 5/16...
Page 8 - Puck Installation; Component Installation
6 Puck Installation Figure 6. Install Pin and Bracket A. Lower ChuteB. Locknut, 1/4-20C. Puck, MetalD. Capscrews, Thin Head, 5/16-18 x 3/4E. Locknuts, 5/16-18F. Bracket A C F G D D E Component Installation BRACKET AND PIN INSTALLATION ON LOWER CHUTE 1. Secure the puck (C, Figure 6) to lower chute (A...
Page 9 - Channel Installation
7 Channel Installation Figure 8. Install Channel AssemblyA. Channel AssemblyB. HitchC. Pin C B INSTALL CHANNEL ASSEMBLY AND “U”-TUBE 1. Slide the channel assembly (A, Figure 8) into hitch (B) as shown. 2. Install the pin (C) into the right side of hitch (B) and turn pin (C) counterclockwise to lock ...
Page 10 - Cover Installation; Bag, Chute and Tube Installation
8 Cover Installation A Figure 11. Install Cover to Channel AssemblyA. CoverB. PinC. Hair PinD. Channel Assembly C B INSTALL COVER TO CHANNEL ASSEMBLY 1. Set the cover (A, Figure 11) on channel assembly. Slide pin (B) through hinge on cover and channelassembly (D) securing with hair pin (C). INSTALL ...
Page 11 - Install Latch & Hinge
Install Latch & Hinge 9 A F B Figure 14. Install Lower Discharge Chute 3A. LowerChuteB. Wing NutC. Rubber StrapD. Carriage BoltE. Discharge DeflectorF. Deflector Hinge RodG. Bracket LOWER DISCHARGE CHUTE INSTALLATION 1. Lift discharge deflector up (D, Figure 14). 2. Slide the notch of bracket (G...
Page 12 - Collector Installation
Normal Removal &Installation 10 Normal Removal & Installation Collector Installation Note: See previous pages for more detailed installationand operation instructions if necessary. 1. Lift discharge deflector up (E, Figure 16). 2. Slide the notch of bracket (G) on to deflector hinge rod (F)....
Page 13 - Normal Removal; Collector Removal
Normal Removal 11 A. Channel Assembly G. Tubes B. Cover H. Boot C. Pin I. Puck D. Hitch J. Discharge Tube E. Bag K. Wire Form F. White Bar L. Seal E D B Figure 17. Normal Installation & Removal C L A G Collector Removal 1. Disconnect the discharge tube (J, Figure 17) from boot (H) by moving wire...