Snapper 1695064 - Manuals

BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagging, air circulation under themow...

Initial Turbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discardthe cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5)...

Initial Turbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot-tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylocknuts. C B Figure...

Initial Turbo Installation 7 Install Idler Assembly & Belt Guider 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3. Mount the idler pulley assembly (A) to the deck u...

Initial Turbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 14) to the sup- port bracket (E) using a 5/16-18 x 1 capscrew (C),washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on thesupport bracket. Different belt covers are required ford...

Initial Turbo Installation 9 Mower DeckArbor Pulley Mower DeckTurbo Drive Pulley Turbo Drive Pulley Idler Pulleys To Slacken Belt CAUTION Before you begin operating the unit with theTurbo attached, be certain you have read all ofthe safety and operational information on the lastpage of this instruct...

Initial Counter Balance & WeightCarrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier InstallationA. Holes D. Rod B. Capscrews, E. Clips, Safety 1/2-13 x 1-1/4 F. Carrier, Weight C. Locknut, 1/2-13 B D A L F G H K I J E C M A. Rear Deck Lift LeverB. Trunni...

Initial Hitch & Tube Installation 11 Figure 1. Install Hitch Plate (Flat Style Bumper)A. Hitch Plate E. Upper & Lower B. Heat Shield Bumper C. Capscrews, F. Washer 1/2-13 x 1-1/4 G. New Holes, 17/32” D. Locknuts, 1/2-13 H. Existing RH Holes Figure 3. Install Hitch AssemblyA. Horizontal Suppo...

Initial Hitch & Tube Installation 12 Figure 5. Assemble Tubes & Deflector A E C F B A. Upper TubeB. Middle TubeC. Lower TubeD. Nut, Nylock, 10-24 x 3/4E. Washer, #10F. Screw, Truss Head, 10-24G. HolesH. Clip and Hardware Assemble Tubes & Deflector 1. Insert the lower tube (C, Figure 5) i...

Initial Collector Assembly 13 Figure 7. Install CatcherA. Nut, #10-32 E. Hinge Pin B. Handle F. Bags C. Screw, #10-32 x 1/2 G. Hair Pin Clip D. Cover Figure 8. Install CableA. Cable C. Washer B. Support A B C D E F G COLLECTOR ASSEMBLY Install Cover and Bags 1. Hang the bags (F, Figure 7) on the hor...

Normal Removal &Installation 14 NORMAL REMOVAL & INSTALLATION Removing the Grass Catcher 1. Disconnect the tubes (A, Figure 9) from the turbo and remove them from the catcher. 2. Remove the hair pin clip (B, Figure 9) and clevis pin (D) securing the cover (E). Disconnect the cable(see Figure...

Removing and Reattaching Grass Catcher 15 Installing the Grass Catcher 1. Set the back plate & support (A, Figure 11) on pins of hitch plate (C). Secure with rod (D) and hair pin (B). 2. Install the bags (C, Figure 12). 3. Install the cover (E, Figure 12). Secure with the cle- vis pins (F) and h...