Snapper 1693756 - Manuals

4 Checks Before Starting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also,refer to the tractor Operator’s Manual and performany required service. 2. Remove any objects from the work area which might interfere with plowing activity. 3. Adjust ...

5 General Operating Instructions Daily Storage 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion. IMPORTANT...

6 Maintenance Schedule For Normal Care Care Required Schedule Clean debris from After each use. dozer blade.Lubricate dozer blade. Every 10 hours or at least once a year. Lubricate Dozer Blade Lubricate the dozer blade as shown in Figure 2. Wherean oil can is shown, wipe the area clean, apply a fewd...

7 Adjustments Skid Shoe Adjustment Slotted holes are provided to permit adjustment of theshoe assemblies for raising and lowering the blade tovarious working heights (see Figure 3). When cleaning snow from gravel or earth drives orwalks, the shoe assemblies should be lowered fully toprevent blade co...

8 Adjustments Figure 6. Adjusting Lift RodA. Front Set CollarB. Rod GuideC. SpringD. Rear Set CollarE. Spring Clip Figure 7. Lift Lever Quadrant - Side View Notch 1 Notch 2 Notch 3 Lift Rod Adjustment ELECTRIC/HYDRAULIC LIFT MODELS: In the fully raised position the blade should be 6” off theground. ...

9 Initial Setup & Assembly Ref Qty Description 1 1 ROD, Control Handle, Upper 2 6 NUT, Hex, 5/16-18 3 2 LOCKWASHER, 5/16 4 4 WASHER, 5/16 5 2 CAPSCREW, 5/16-18 x 1-1/4 6 1 ROD, Control Handle, Lower 7 1 CLEVIS 8 1 WASHER, 1/2 9 1 CLIP, Hair Pin 10 3 COTTER PIN 11 1 ROD & PLATE ASMY, Pivot 12...

11 Initial Setup & Assembly INITIAL SETUP & ASSEMBLY NOTE: Some of the following setup procedures mayalready be completed. Assemble Blade 1. Place the blade on a flat surface. 2. Baron/Broadmoor/LT/1600/2600 Series: See Figure 10. Install one bar stop (A) using the two 5/16-18 x 1taptite scr...

12 Initial Setup & Assembly Install Rear Push Bar Support NOTE: Manual Lift Models-If your tractor is not alreadyequipped with a Large Lift Lever kit, install it at this time.Follow the instructions supplied with the kit. 1. Assemble the push bar support (A, Figure 12) and hitch (F) using the ha...

13 Initial Setup & Assembly Figure 15. Install Push Bar AssemblyA. Push Bar Assembly C. Clevis Pins B. Hitch D. Safety Clips Figure 14. Installing Hitch to Rear BracketA. Push Bar Support C. Lift Rod/Lever B. Washers CONNECT HITCH TO REAR PUSH BAR 1. Slide the push bar support (A, Figure 14), an...

14 Initial Setup & Assembly Install Spring Assist Bracket (Baron/Broadmoor/1600/2600 Models Only) NOTE: Spring-assist bracket assembly (Figure 16) doesnot need to be installed on units with electric/hydraulic lift. 1. Install the spring-assist bracket (A, Figure 16) to trac- tor frame (bracket i...

15 Initial Setup & Assembly Install Lift Rod NOTE: Two lift rods are packaged with theBroadmoor/LT/1600/2600 & Landlord/GT/1700/2700hitch assembly. Use the correct lift rod for manual orhydraulic lift as shown in Figure 9. 1. Assemble lift rod per Figure 19. 2. Insert prong of rod guide (A, ...

16 Initial Setup & Assembly Figure 23. Control Rod SupportA. SupportB. 5/16-18 x 1-1/2 CapscrewsC. 5/16 Centerlock NutsD. 5/16 Plain WashersE. Spacers Install Angling Control Rod NOTE: If installing the dozer attachment on a unitequipped with a snowcab, replace the control rod sup-port (A, Figur...

17 Removing & Attaching the Hitch & Blade REMOVAL & INSTALLATION Removing & Attaching Dozer Blade 1. Lower the blade. Put the lift lever in the middle notch (float position). 2. Remove the hair pin clip and washer (D, Figure 25) securing the angling control rod to the clevis.Disconne...

18 Removing & Attaching Removing & Attaching Hitch 1. Remove the safety clip (A, Figure 26) and remove the hitch pin (D). 2. Lift the hitch bar (B) off the tractor brackets (C). 3. Remove the spring clips (A, Figures 28 & 29) secur- ing the rear hitch bracket (C) to the lift pivot rod (B...

19 Reinforcement Bracket Installation INSTALL REINFORCEMENTBRACKET NOTE: This kit applies to the Landlord / 1700 / 2700Series hydraulic lift models only. 1. Loosen the four capscrews (A, Figure 32) securing the quadrant (B) to the footrest. 2. Insert the reinforcement bracket (B, Figure 31) between ...

Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7....