Snapper 1662-0 - Manuals

Snapper 3500 PSI Pressure Washer 6 • Insert the “L” bolt through the hole on the right side of the handle (viewing from rear of unit) and attach theplastic knob (Figure 2). Tighten the knob by hand. If notinstalled, add the vinyl cap to the “L” bolt. • Insert the multi–colored nozzles in the spaces ...

Snapper 3500 PSI Pressure Washer 7 Connect Hose and Water Supply to Pump IMPORTANT: You must assemble the nozzle extensionto the spray gun and attach all hoses before you start theengine. Starting engine without all hoses connected andwater supplied will damage the pump. • Uncoil high pressure hose ...

Snapper 3500 PSI Pressure Washer 8 HOW TO USE YOUR PRESSURE WASHER If you have any problems operating your pressure washer,please contact the local Snapper service center. How to Start Your Engine The best way to start your pressure washer for the firsttime is to follow these instructions step–by–st...

Snapper 3500 PSI Pressure Washer 9 • If the choke lever has been moved to the “Choke” position to start the engine, gradually move it to the“Run” position as the engine warms up. • Attach the nozzle extension to the spray gun. Tighten by hand (Figure 13). • Select the desired quick connect nozzle an...

Snapper 3500 PSI Pressure Washer 10 Cleaning and Applying Chemical CAUTION! You must attach all hoses before you start the engine. Starting the engine without all the hosesconnected and without the water turned ON will damagethe pump. IMPORTANT: Use soaps designed specifically forpressure washers. H...

Snapper 3500 PSI Pressure Washer 11 SPECIFICATIONS Rated Pressure . . . . . 3500 PSI Flow Rate . . . . . . . . . . 3.5 gallons per minute (gpm) Detergent . . . . . . . . . . Use detergent approved for pressure washers Water SupplyTemperature . . . . . . . Not to exceed 100°F Automatic Cool . . . . W...

Snapper 3500 PSI Pressure Washer 12 Check Gun and Nozzle Extension Examine the hose connection to the spray gun and makesure it is secure. Test the trigger by pressing it and makingsure it springs back into place when you release it. Put thesafety latch in the on position and test the trigger. Yoush...

Snapper 3500 PSI Pressure Washer 13 6. Reinstall the nozzle and in-line filter into the nozzleextension. Do Not overtighten the nozzle with theallen wrench. 7. Reconnect the nozzle extension to the spray gun. 8. Reconnect the water supply, turn on the water, andstart the engine. 9. Test the pressure...

Snapper 3500 PSI Pressure Washer 15 TROUBLESHOOTING Problem Cause Correction Pump has following problems: failure to produce pressure, erratic pressure, chattering, loss of pressure, low water volume. 1. Low pressure nozzle installed. 2. Water inlet is blocked. 3. Inadequate water supply. 4. Inlet h...

Snapper 3500 PSI Pressure Washer 16 EXPLODED VIEW — UNIT

Snapper 3500 PSI Pressure Washer 17 PARTS LIST — UNIT Item Part # Qty. Description 1 L189641GS 1 BASE 2 B2043GS 8 BOLT, Carriage 3 187978GS 1 KIT, Handle Hardware 4 C190293GS 1 HANDLE 5 CB1981GS 2 SUPPORT, Handle 6 99583GS 8 NUT, Hex Flange 7 B2150GS 1 HOOK, 5/16" Square Neck Gun 8 B2516GS 3 CAP...

Snapper 3500 PSI Pressure Washer 18 EXPLODED VIEW — PUMP

Snapper 3500 PSI Pressure Washer 19 PARTS LIST — PUMP Item Part # Qty Description 0 187263GS 0 Complete Pump Assy (see also pages 20-21) 1 101B2327GS 6 Plug 2 100B2327GS 6 O-Ring 3 102B2327GS 6 Valve 4 103B2327GS 6 O-Ring 5 104B2327GS 2 Plug 6 105B2327GS 2 O-Ring 7 106B2327GS 3 Support Ring 8 107B23...

Snapper 3500 PSI Pressure Washer 20 EXPLODED VIEW — UNLOADER

Snapper 3500 PSI Pressure Washer 21 PARTS LIST — UNLOADER Item Part # Qty Description 0 153B2126GS 0 Complete Unloader 1 210B2327GS 1 Hose Tail 2 231B2327GS 3 O-Ring 3 211B2327GS 1 Stainless Ball 4 212B2327GS 1 Spring 5 213B2126GS 1 Injector Body 7 215B2327GS 1 Injector Nut 8 137B2327GS 1 O-Ring 9 2...