SMC PF5M - Manuals - manualsarea.com

Page 2 - OPERATOR; CONTENTS

Safety Instructions 2 Names and Functions of Individual Parts 7 Model Indication Method 8 Mountin and Installation 10 Installation 10 Pipimg 13 Wiring 14 Error Indication 16 1 Thank you for purchasing the SMC PFM5 Series Digital Flow Sensor.Please read this manual carefully before operating the digi...

Page 3 - Safety Instructions; IMPORTANT MESSAGES; Gives you helpful information.; Do not operate outside of the specification.

3 2 Safety Instructions The Digital Flow Sensor have in after referred to as flow sensorand this manual contain essential information for the protectionof users and others from possible injury and property damageand to ensure correct handling.Please check that you fully understand the definition of ...

Page 4 - Precaution on Handling; Use UL approved product for direct current power supply.; NOTE

5 4 Safety Instructions (continued) Perform proper functional checks and leak tests aftermaintenance. Stop operation when an abnormality is observed such that the flowsensor does not work properly or there is a leakage of fluid.Safety is not be assured due to unexpected malfunction.When leakage occu...

Page 5 - Names and Functions of Individual Parts

7 6 Names and Functions of Individual Parts Power source display (green) : Turns on when power is supplied.Flow display (green) : Flashing interval depends on the flow value. As flow increases, flash interval is shortened. The light turns to red when rated flow is exceeded. Body : Flow sensor itself...

Page 6 - Model Indication Method

9 8 Model Indication Method - - - 12 Analog (1 to 5V) Contente Model Analog (4 to 20mA) PFM30 series Applicable model PFM31 series Output specification Option2 Nil RS No option PFM5 - - / PFM5 (S)- L- PFM5 - - PFM5 - (L)- PFM5 S- (L)- ZS-33-M ZS-33-MS ZS-33-J ZS-33-JS Option parts Model Bracket (Flo...

Page 7 - bracket mounting; Mounting and Installation; Installation; How to mount

Section A Panel Mount Adapter A Panel Panel Mount Adapter B Push Insert Bracket Section C 24 +0.5 0 A 11 10 bracket mounting •Fasten the bracket mounting screws at a clamping torque of 0.5 0.05N·m. IN 1 Attached tapping screw Attached tapping screw Without flow adjustmentvalve (using ZS-33-M) With f...

Page 8 - Piping; •Insertion with excess force

13 12 Piping Mounting and Installation (continued) •Keep the tightening torque when piping for the female thread.•Refer to the following table for the appropriate torque values. Nominal size of screws Appropriate torque N · m Rc1/8 7 to 9 Rc1/4 12 to 14 •For one-touch fitting, insert the tube to the...

Page 9 - Wiring; Connection; • Be sure to ground terminal FG when using a switching regulator; , or by using a seriespower supply instead of a switching; Connector; • When disconnecting the connector, push down the lever by thumb; Connector Connecting / Disconnecting; Output circuit; Select response speed; • To reduce ripple by slowing the response speed when ripple of; How to select

15 14 Mounting and Installation (continued) Wiring Body of sensor Lever Cover (Option:ZS-33-F) Lead wire connector Connection • Make connection after turning the power off.• Use a separate route when installing wire. Malfunction stemming from noise may occur if wire is installed inthe same route as ...

Page 10 - Error Indication; Error indication function; Error Name

16 Error Indication This function is to display error location and content when aproblem or an error occurs. Error indication function If the above remedy can't recover the operation, the error needs to beinvestigated by SMC. Error Name System Erro Error Content Troubleshooting Error Display System ...