SMC IZS30 SERIES - Manuals

SMC IZS30 SERIES – Manual in PDF format online.

Manuals:

Manual

Manual SMC IZS30 SERIES

Summary

Page 2 - Contents

Contents 1. Safety instructions.........................................................................................................2 2. How to order...................................................................................................................6 3. Specifications ...............

Page 3 - Safety instructions; WARNING; or decides its specifications.; equipment, and exhaust all residual compressed air in the system.; take appropriate measures and contact SMC.; animals requiring special safety analysis.

1. Safety instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard by labeling "Caution" , "Warning" , and "Danger" . To ensure safety, be sure to observe ISO4414, JI...

Page 4 - Installation

WARNING 1. This product is made for general industry. Contact SMC before use, if you are planning to use for other purposes. 2. Use under specified voltage and temperature. Voltage out of specification may cause malfunction, breakage, electric shock and fire. 3. Use clean compressed air for fluid. T...

Page 5 - Wiring and piping

WARNING 1. Check that power supply capacity is enough and voltage is in specification before piping. 2. Apply type D earthing to prevent electrical shock in accordance with instructions on this operation manual. 3. Be sure to cut off power supply at wiring (inclu/ding connector plug-in/out) . 4. Use...

Page 6 - Maintenance

product. k. The place where strong high frequency is generated. l. The place where lightning disaster is expected. m. The place where the product is directly exposed to the vibration and impact. n. The situation where the force and weight that causes deformation of the product is applied. 3. Do not ...

Page 10 - Detent

4. Adjust angle of the ionizer body to ensure proper static charge elimination, and fix it with detent threads (M5) of brackets. Recommended tightening torque for detent thread: 1.5Nm 4-2. Installation of surface electric potential sensor In case of using a surface electric potential sensor, install...

Page 11 - Seal

3. Peal off the seal attached on the detecting hole of the surface electric potential sensor. 4. Direct the surface electric potential sensor to the target’s static charge as adjusting the angle, and fix the detent thread (M5) of bracket. Recommended tightening torque for detent thread : 1.5 Nm 4-3....

Page 12 - Modular plug

2. Arrange lead wires in accordance with the wiring table. The unused wires should be cut short or covered with vinyl tape without pealing the coat to prevent them from coming contact with other wires. See [4-4. Connection circuit ]. Wiring table for power supply cable IZS30-CP Note No. 6 and 8 only...

Page 15 - Ionizer; Power supply; OUTPUT; PLC

4-4. Connection circuit Ionizer POWER connector [Note 1] indicates the coating color for lead wire of dedicated cable [Note 2] Connect [4. Stop signal of static charge elimination] to GND when starting the ionizer operation. When the terminal is open, the operation will stop. [Note 3] [6. signal for...

Page 16 - Function description; Supplied voltage wave form image diagram; ng; Polarity image of; Pulsed DC

5. Function description 5-1. Operation mode Three operation modes are available in IZS30. Use these modes depending on applications and operating conditions. Supplied voltage wave form image diagram Op. mode Operation Features Precautions S en si ng D C m od e After surface electric potential sensor...

Page 17 - -3. Function description of indication

5-2. Output signal Signal type Function Signal for static charge elimination completion (When surface electric potential sensor is used) Output when static charge elimination is completed, or no target’s static charge exists. Abnormal high voltage Output when any discharge probe gets shorted with ot...

Page 19 - Installation distance mm; Operating frequency; With sensor

7. Technical data 7-1. Static charge elimination characteristics (reference 1. Installation distance and static charge elimination time Target’s static charge work Charged plate dimensions:150×150mm Capacity:20 @ F Mean.Cond.:Static el.Time for 3kV A 0.3kV Installation distance and static charge eli...

Page 20 - Static charge elimination area; Ionizer depth direction; Ionizer width direction

2. Static charge elimination area Ionizer depth direction Ionizer width direction E F E G0EE G F E HEE I H F E I HEE I G F E I G0EE I F E E F E G0EE G F E HEE H F E J0KMLON J0KMLON J0KMLON J0KMLON PQKMJON PQKMJON PQKMJON PQKMJON RSKMJON RSKMJON RSKMJON RSKMJON Target’s work of static charge Charged ...

Page 21 - Air purge amount : 20

Ionizer depth direction (with air purge) Ionizer width direction ] with air purge ^ F E G0EE G F E HEE F E E F E GSEE GSEE F E E F E W XSY W XSY W XSY W XSYZ Z Z Z [ X W [ X W [ X W [ X W Z Z Z Z \ X W \ X W \ X W \ X W Z Z Z Z F E G0EE G F E HEE I HEE I G F E I GSEE I F E E F E GSEE J0KMLON J0KMLON...

Page 22 - Charged amount and static charge elimination time; Common conditions; Installed height:250mm; Ch; With Sensor

Charged amount and static charge elimination time Operating frequency and static charge elimination time (W/O surface electric potential sensor) ` ` ` ` Common conditions ` ` ` ` Installed height:250mm Air purge amount:20 l / min ANR Op.freq.(in case of W/O sensor) : 33Hz W/O Sensor With Sensor Ch a...

Page 23 - Model

7-2. Outline dimensions 1. Ionizer (IZS30-**) n (Number of Cartriges) Model n L (mm) IZS30-300** 3 300 IZS30-780** 9 780 IZS30-1260** 15 1260 IZS30-1500** 18 1500 IZS30-1900** 23 1900 1Hz Op.freq.33Hz Installation distance mm St at ic ch ar ge e lim in at io n tim e s ec ab c 2-Pipefitting with chec...

Page 24 - Intermediate bracket

End bracket (IZS30-BE) Intermediate bracket } } } } IZS30-BM ~ ~ ~ ~ )h dl g0i dQ j a k Thread for mounting M5 (Should be prepared by user) Angle ajustment available (± 90° ) a b j a b f e gMi dQ j e b f e Thread for mounting M5 (Should be prepared by user) dQho g)iSu ...