Simplicity Snow Plow/Dozer Blade - Manuals

Page 2 - STANDARD

HEX CARRIAGE BOLT PLAIN WASHER LOCKWASHER NUT HEX IDENTIFICATION Shown below are actual size heads for standard screw sizes.Example: a screw has head and thus requires a w r e n c h . T o m e a s u r e l e n g t h , u s e t h e s c a l e b e l o w . Head Head screw with screw with S.D. 6” Head Head ...

Page 3 - Table of Contents; SAFETY RULES; Accessories

Table of Contents STANDARD FASTENER IDENTIFICATION CHART ...................................................... Inside F r o n t Cover SAFETY RULES G e n e r a l .............................................................................................................................................

Page 4 - safety Rules

safety Rules Read these safety rules and follow them closely. Failure to obey these rules could result in loss of con- t r o l o f v e h i c l e , s e v e r e p e r s o n a l i n j u r y t o y o u r s e l f o r b y s t a n d e r s , o r d a m a g e t o p r o p e r t y o r e q u i p m e n t . T h e i...

Page 5 - 2” Snow Plow/Dozer Blade; PARTS ILLUSTRATION

42” Snow Plow/Dozer Blade PARTS ILLUSTRATION location garden tractors on page 6). Spring location for lawn tractors(see chart on page 6). NO. A 1 BCD 2 E F 2 G 4 H Set Description SPRING, Clip BAR ASSY., Push PIN, Pivot SPRING GUIDE ASSY., Rod SETSCREW, ROD. Lift T NO. B L A D E Description U 0 TRIP...

Page 6 - ASSEMBLY

42” Snow Plow/Dozer Blade ASSEMBLY 1. Place the blade on a flat surface. 2. install two bar stops (A, figure 2) using the two 8 (B). Figure 2. Bar Stop A. Bar Stop B. Taptite Screw, 6-l 8 1 Insert (A, figure 3) on blade and screw on nut (B) only far enough that it is flush with the end of the 4. Hoo...

Page 8 - Location; Lower the push bar and tighten the

42” Snow Plow/Dozer Blade 5. Raise the push bar and hook up the spring (A, fig- ure 6) in location or C as follows: Location T r a c t o r ( S e r i e s ) C I 6000,800, I 6. Lower the push bar and tighten the and nut which hold chain to tractor frame. gure 6. Lift-Assist Spring S p r i n gSpring Loc...

Page 9 - Figure 7. Dozer Blade Assembled

42” Snow Plow/Dozer Blade 7. Insert front of push bar (A, figure 7) into pivot frame on rear of blade. Then install king pin (C)down thru holes in and pivot frame. Secure king pin (C) with spring clip (D). 8. Using king pin as the pivot, swivel push bar to align holes for pivot pin (E). Then install...

Page 11 - ADJUSTMENTS; ground contours may require differ-; Wear Plate

42” Snow Plow/Dozer Blade Normal Care After dozing jobs, hose down the blade to remove excess dirt. Coat bare metal surfaces to prevent rust-ing. Lightly oil all pivot points. If the wear plate (A, figure 9) on the bottom of the 42”blade is worn excessively, replace it a new one by removing the six ...

Page 12 - Skid Shoes

42” Snow Plow/Dozer Blade Skid Shoes Alternate holes are provided to permit adjustment ofthe shoe assemblies for raising and lowering theblade to various working heights (see figure 11).When cleaning snow from gravel or earth drives orwalks the shoe assemblies should be lowered fully toprevent blade...

Page 15 - S E E

TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE S E E SAE GRADE 0 N m . Nm. Nm. a-32 19 2.1 30 3.4 4.8 8-38 20 2.3 3.5 43 4.9 27 3.1 43 4.9 8 0 8.8 31 3.5 49 5.5 7.7 88 7.8 12 18.3 78 8.8 10 13.8 14 19. 15. 17 23.1 25 34. 12 18.3 19 25.8 2 5 34. 20 27.2 30 40.8 4 5 81.2 35 47.8 5 0 31....