Simplicity 755M - Manuals - manualsarea.com

Page 3 - Table of Contents; SNOWTHOWER COMPONENTS

1 TP-400-2561-00-IW-S Table of Contents SNOWTHOWER COMPONENTS PAGES Handles and Controls Group .....................................2 Frame and Engine Group...........................................6 Auger Drive and Impeller Group..............................10 Auger Housing and Chute Group .........

Page 4 - Handles and Controls Group

2 TP-400-2561-00-IW-S Handles and Controls Group NOTE: Unless noted otherwise,use the standard hardware torquespecification chart. 985917 Apply adhesive to secure grips. Ref. 29 required on slotted holes only. Shift rod assembly (Ref. 20) must pivot freely on pivot blocks (Ref. 14). Slot in support ...

Page 5 - DESCRIPTION

3 TP-400-2561-00-IW-S Handles and Controls Group 1 1668525 2 ROD, Control, Lower 2 1669323 2 SPRING, Extension 3 1916621 4 NUT, Hex, #10-24 R.H. 4 1715132 1 CLUTCH ROD, Auger Drive 5 1722636 1 HANDLE, R.H. (Auger Control side) 6 1722638 1 LEVER, Auger Clutch, R.H. 7 1676954 2 GRIP, Black Vinyl, for ...

Page 8 - Frame and Engine Group

6 TP-400-2561-00-IW-S Frame and Engine Group NOTE: Unless noted otherwise,use the standard hardware torquespecification chart. 985620 Attach to Frame Right rear only. Engine Use upper square hole on 5 HP and lower square hole on 7 HP. Required on rear engine bolts only. Torque all engine bolts to 19...

Page 12 - Auger Drive and Impeller Group

10 TP-400-2561-00-IW-S Auger Drive and Impeller Group NOTE: Unless noted otherwise,use the standard hardware torquespecification chart. 985496 Apply a bead of gasket eliminator into rear seal groove and flat surface just past groove (Ref. 15 & 20) on both halves. Also, apply to bushing bore surf...

Page 14 - Auger Housing and Chute Group

12 TP-400-2561-00-IW-S Auger Housing and Chute Group NOTE: Unless noted otherwise,use the standard hardware torquespecification chart. 985918 Place Ref. 3 between chute and deflector. Seal must cover openings at hinge pivot. Coat top and bottom of chute ring with grease. Mounts to underside of housi...

Page 16 - Traction Drive Group

14 TP-400-2561-00-IW-S Traction Drive Group NOTE: Unless noted otherwise,use the standard hardware torquespecification chart. 984936 Apply loctite to screws and torque to 55 - 60 in-lbs (2 places). Pack groove with grease. Apply locktite and torque to 8 - 10 ft. lbs. Retainer to be loacted inside fr...

Page 19 - Decals Group

17 TP-400-2561-00-IW-S Decals Group 1 1715557 1 DECAL, Speed Selector 2 1722640 1 DECAL, Auger Control 3 1722643 1 DECAL, Warning / Main Dash Panel 4 1715558 1 DECAL, Simplicity Logo 5 1714107 1 DECAL, 755 5 1714108 1 DECAL, 555 6 1722674 1 DECAL, Danger, Discharge Chute 7 1716532 1 DECAL, Danger, A...

Page 20 - Wheels and Tires Group

18 TP-400-2561-00-IW-S Wheels and Tires Group NOTE: Unless noted otherwise,use the standard hardware torquespecification chart. 984933 4 3 1 6 5 2 The above parts group applies to the following Mfg. Nos.: 1693980 555M, 5HP Manual Start 1693981 555M, 5HP Manual Start (Exp.) 1693982 755M, 7HP Manual S...

Page 22 - Torque Specification Chart; Size Of; NOTES; Hardware Identification & Torque Specifications; Common Hardware Types; Wrench & Fastener Size Guide; Standard Hardware Sizing

Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7....