Simplicity 1726793 - Manuals

Simplicity 1726793 – Manual in PDF format online.

Manuals:

Manual

Manual Simplicity 1726793

Summary

Page 2 - THIS PAGE INTENTIONALLY BLANK

Page 3 - ATTACHMENT; Clean Sweep; Twin Catcher

ATTACHMENT OPERATOR’SMANUAL Clean Sweep Twin Catcher Mfg. No. Description 1694498 Clean Sweep Twin Catcher 1726793 Rev. 02 Rev. Date 03/2004 TP 100-4033-02-AT-SN Clean Sweep Twin Catcher

Page 5 - Table of Contents

1 Initial Collector Assembly Install Cover & Bags ......................................13 Normal Removal & Installation Removing the Grass Catcher ........................14 Installing the Grass Catcher ..........................15 Hardware Identification & Torque Specifications...........

Page 6 - SAFETY DECALS; GENERAL WARNINGS; ATTACHMENT DECALS

2 Safety Rules& Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian-gle in text signifies important cautions or warnin...

Page 7 - General; WARNING; REQUIRED ACCESSORIES; AFTER OPERATION; STORING THE GRASS CATCHER; CAUTION

BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagging, air circulation under themow...

Page 9 - Initial Turbo Installation; Install Deflector Hinge Assembly; Install Discharge Baffle; TURBO INSTALLATION; Deflector Removal

Initial Turbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discardthe cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5)...

Page 10 - Install Deflector

Initial Turbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot-tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylocknuts. C B Figure...

Page 11 - Install Idler Assembly & Belt Cover

Initial Turbo Installation 7 Install Idler Assembly & Belt Cover 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3. Mount the idler pulley assembly (A) to the deck us...

Page 12 - Install Belt Cover Plate; Install Turbo Belt; Install Mounting Bracket

Initial Turbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 13 & 14) to the support bracket (E) using a 5/16-18 x 1 capscrew (C),washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on thesupport bracket. Different belt covers are requir...

Page 13 - Install Turbo Drive Belt; Secure Belt Cover

Initial Turbo Installation 9 Mower DeckArbor Pulley Mower DeckTurbo Drive Pulley Turbo Drive Pulley Idler Pulleys To Slacken Belt CAUTION Before you begin operating the unit with theTurbo attached, be certain you have read all ofthe safety and operational information on the lastpage of this instruct...

Page 14 - Counter Balance Installation; Front Weight Carrier Installation

Initial Counter Balance & WeightCarrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier InstallationA. Washer, 5/16 E. Clips, Safety B. Capscrew, 5/16-18 x 1 F. Carrier, Weight C. Locknut, 5/16-18 G. Holes D. Rod B D A L F G H K I J E C M A. Rear Deck Lift L...

Page 15 - Tube Installation; HITCH & TUBE INSTALLATION; Install Hitch Plate and Back Plate

Initial Hitch & Tube Installation 11 Figure 1. Install Hitch PlateA. Hitch Plate E. Upper & Lower B. Heat Shield Bumper C. Capscrews, F. Washer 1/2-13 x 1-1/4 G. New Holes, 17/32” D. Locknuts, 1/2-13 H. Existing RH Holes Figure 3. Install Back PlateA. Back Plate and Support C. Hitch PlateB. ...

Page 16 - Initial Hitch & Tube Installation; Assemble Tubes & Deflector; Assemble Catcher Bags

Initial Hitch & Tube Installation 12 Figure 4. Assemble Tubes & Deflector A E C F B A. Upper TubeB. Middle TubeC. Lower TubeD. Nut, Nylock, 10-24 x 3/4E. WasherF. Screw, Truss Head, 10-24G. HolesH. Clip and Hardware Assemble Tubes & Deflector 1. Insert the lower tube (C, Figure 4) into m...

Page 17 - COLLECTOR ASSEMBLY; Install Cover and Bags

Initial Collector Assembly 13 Figure 7. Install CatcherA. Nut, #10-32 E. Hinge Pin B. Handle F. Bags C. Screw, #10-32 x 1/2 G. Hair Pin Clip D. Cover Figure 8. Install CableA. Cable C. Washer B. Support A B C D E F G COLLECTOR ASSEMBLY Install Cover and Bags 1. Hang the bags (F, Figure 7) on the hor...

Page 18 - NORMAL REMOVAL & INSTALLATION; Removing the Grass Catcher

Normal Removal &Installation 14 NORMAL REMOVAL & INSTALLATION Removing the Grass Catcher 1. Disconnect the tubes (A, Figure 9) from the turbo and remove them from the catcher. 2. Remove the hair pin clip (B, Figure 9) and clevis pin (D) securing the cover (E). Disconnect the cable(see Figure...

Page 19 - Removing and Reattaching Grass Catcher; Installing the Grass Carcher

Removing and Reattaching Grass Catcher 15 Installing the Grass Carcher 1. Set the back plate & support (A, Figure 11) on pins of hitch plate (C). Secure with rod (D) and hair pin (B). 2. Install the bags (C, Figure 12). 3. Install the cover (E, Figure 12). Secure with the cle- vis pins (F) and h...

Page 20 - Torque Specification Chart; Hardware Identification & Torque Specifications; Wrench & Fastener Size Guide

16 Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68...