Simplicity 1695514 - Manuals

Simplicity 1695514 – Manual in PDF format online.

Manuals:

Manual

Manual Simplicity 1695514

Summary

Page 2 - THIS PAGE INTENTIONALLY BLANK

THIS PAGE INTENTIONALLY BLANK (FOR PLACEMENT ONLY - DO NOT PRINT)

Page 5 - Table of Contents; WARNING

1 Table of Contents CONTENTS: Safety Rules & Information General ...................................................................2Training ...................................................................4Preparation .............................................................4Operation .....

Page 7 - Safety Rules and Information

3 Moving Parts This equipment has many moving parts that can injure you or someone else.However, if you are standing in the operator’s position, and follow all the rules inthis book, the unit is safe to operate. The auger and impeller have spinning parts that can amputate hands and feet.Do not allow...

Page 9 - S a f e t y R u l e s; CHILDREN

5 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both shortand long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit toservice. 10. Maintain or replace safety and instruction l...

Page 10 - P r o d u c t I d e n t i f i c a t i o n; xxx; LE; xxx; dB; CE IDENTIFICATION TAG MARKINGS; Identification Numbers

6 P r o d u c t I d e n t i f i c a t i o n ID Tag When contacting your authorized dealer for replace-ment parts, service, or information you MUST havethese numbers. Record your model name/number, manufacturer’s identi-fication numbers, and engine serial numbers in thespace provided for easy access....

Page 11 - SAFETY DECALS; International Symbols

7 P r o d u c t I d e n t i f i c a t i o n SAFETY DECALS Safety warning decals are placed at strategic locations on the snowthrower as a constant reminder to the opera-tor of the most important safety precautions. All warning, caution and instructional messages on your snowthrow-er should be carefu...

Page 12 - Snowthrower

8 TOOLS REQUIRED • Knife REMOVAL FROM CARTON 1. Locate and remove container of oil. 2. Locate all parts packed separately and remove from carton. NOTE: Set the fuel stabilizer aside until adding gasolineto the fuel tank. We recommend that fuel stabilizer beadded to the fuel each time that gasoline i...

Page 13 - Engine; Assembling the Snowthrower

9 2. Attach the auger drive cable (C, Figure 3) to the auger drive lever (A) using the Z-hook (B). 3. Remove the T-knob (B, Figure 4) and bolt on the upper chute. 4. Rotate the upper chute (A) to the operating position (past the lower chute stop) 5. Install the bolt and tighten the T-knob (B). Engin...

Page 14 - SNOWTHROWER CONTROLS; Deflector Controls

10 Controls& Operation AugerControl ChuteDirectionControl Chute Deflector A B C Engages auger when pulledback, and disengages augerwhen released. Rotates discharge chute todesired direction. Controls vertical angle snow isthrown. Figure 7 . Snowthrower Controls A B C SNOWTHROWER CONTROLS Auger C...

Page 15 - ENGINE & STARTING CONTROLS

11 Controls & Operation ENGINE & STARTING CONTROLS NOTE: This snow thrower does NOT have a throttle forcontrolling operating speed of engine. The engine gover-nor maintains operating speed for varying snow removalconditions. A. Electric Start Button - The Electric Start Button (A, Figure 8) ...

Page 16 - GENERAL OPERATION; CHECKS BEFORE EACH START-UP; DANGER; OPERATIONAL WARNINGS; Clearing The Discharge Chute; Discharge Chute Adjustment

12 GENERAL OPERATION CHECKS BEFORE EACH START-UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check the fuel supply. Fill the tank no closer than 1/4 to 1/2 inch of top of tank to provide space for expan-sion. See your engine Owner’s Manual for fuel rec-om...

Page 17 - ADDING ENGINE OIL; ADDING FUEL

13 ADDING ENGINE OIL 1. Make sure the unit is level. Use a high quality deter- gent oil classified “For Service SG, SH, SJ, SL, orhigher”. 2. Remove the oil fill cap/dipstick access panel (A, Figure 9). 2. Remove the oil fill cap/dipstick (B) and wipe with a clean cloth. 3. Insert the oil fill cap/d...

Page 20 - LUBRICATION

RegularMaintenance 16 Before beginning any repair stop the engine,remove the key, disconnect the spark plug wire,and wait for all moving parts to stop. WARNING Figure 10. Lubrication points Figure 11. Grease the Discharge Chute Ring LubricateFlange LUBRICATION NOTE: The drive pulley end of auger sha...

Page 21 - Troubleshooting; TROUBLESHOOTING

17 Troubleshooting & Service Figure 12. Chute Removal and InstallationA. ChuteB. Fasteners A B B B B CHUTE REMOVAL ANDINSTALLATION 1. Remove the fasteners (B, Figure 12) that secure the chute (A) to the top cover. 2. Remove the chute (A). 3. Installation is reverse of removal. TROUBLESHOOTING Pr...

Page 22 - Troubleshooting & Service

18 A C C C B B C A B B C C E D Figure 13. Top Cover and Belt CoverA. Screw, 1/4-20 x 5/8B. Screw, #10-24 x 1/2C. Screw, 1/4-14 x 3/4D. Top CoverE. Belt Cover COVER REMOVAL ANDINSTALLATION To access the drive system or the engine, the coversmust be removed as follows: REMOVE THE TOP COVER 1. Remove t...

Page 23 - REPLACE DRIVE BELT

REPLACE DRIVE BELT The drive belt is of special construction and must bereplaced with original factory replacement belt availablefrom your nearest dealer. 1. Remove the belt cover. See “Remove The Belt Cover”. 2. Remove the drive belt (E, Figure 14) from the idler pulley (G). 3. Move the belt guide ...

Page 24 - SERVICING THE SPARK PLUG

20 SERVICING THE SPARK PLUG 1. Remove engine key from switch. 2. Remove the oil access cover. 3. Disconnect the wire from the spark plug. 4. Inspect the spark plug and clean. If necessary, replace it with a new spark plug as recommended inthe engine Owner’s Manual. 5. Adjust the gap on the spark plu...

Page 25 - AUGER DRIVE CABLE ADJUSTMENT

AUGER DRIVE CABLE ADJUSTMENT The auger drive cable is adjusted at the factory and noadjustment should be necessary. If the cable becomesstretched or is sagging, adjustment will be necessary. Whenever the belt is adjusted or replaced, the cable willneed to be adjusted. 1. Remove the Z-hook (C, Figure...

Page 26 - Specifications

22 ENGINE: 5.25 Series Briggs & Stratton Make Briggs & Stratton Domestic Model / Type 09A413 / 0202E1 CE Model / Type 09A413 / 0203E1 Gross Torque* 5.25 ft. lbs. @ 3060 rpm Displacement 9.02 Cu. in (148 cc) CHASSIS: Spout Rotation 190 Degrees Auger Diameter 9” (22.9 cm) Tire Size 7” x 1.5” (...