Simplicity 1694439 - Manuals

5 Identification Tags When contacting your authorized dealer for replace-ment parts, service, or information you MUST havethese numbers. Record your model name/number, manufacturer’s identi-fication numbers, and engine serial numbers in thespace provided for easy access. These numbers can befound in...

6 Safety Decals Part No. 1722674 Discharge Chute Danger Decal Part No. 1722641 Discharge Chute Danger Decal Part No. 1722642 Auger Danger Decal Part No. 1722643 WARNING / Main Dash Decal, North American Models Part No. 1722639 WARNING / Main Dash Decal, CE Models Part No. 1722640 Auger Control Decal...

Warning: Read Operator’s Manual. Read and understand the Operator’sManual before using this machine. 7 Safety Icons Danger: Thrown Objects. This machine is capable of throwingobjects and debris. Keep bystandersaway. Warning: Remove Key BeforeServicing. Remove the key, disconnect sparkplug wire, and ...

9 Features & Controls Fuel Fuel tank filler cap (see illustration). The fuel shut offvalve is located under the fuel tank. Close the valvewhen the snowthrower is not in use. Open the valvebefore stating. Starter Handle Used to pull-start the engine. Primer Button Primes carburetor for faster col...

10 Engine Controls STARTING CONTROLS See Figure 1 for the following instructions. Units with Optional Electric Start A. Electric Start Button - The Electric Start Button (A) activates an electric starter mounted to theengine, eliminating the need to pull the starter han-dle. The Electric Start Butto...

11 Controls Figure 2. Operator's Control PositionA. Speed Selector C. Auger Control B. Traction Control D. Chute Direction Control Figure 3. Snowthrower ControlsA. Speed Selector E. Chute Deflector B. Traction Drive Control F. Chute Deflector Knob C. Auger Control G. Skid Shoes D. Chute Control H. T...

12 Operation GENERAL OPERATION CHECKS BEFORE EACH START-UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check the engine oil level. See your engine Owner’s Manual for procedure and specifications. 3. Check to make sure spark plug wire is attached and spark...

13 Operation STARTING THE ENGINE Refer to Figure 4. 1. Turn the fuel valve (B) to the ON position. 2. Insert the engine key (F) into the engine key slot. 3. Move the throttle lever (E) to the FAST position. 4. Fully close the choke (G) if engine is cold (a warm engine may not require choking). 5. Pu...

14 Operation OPERATING THE SNOWTHROWER 1. Rotate the discharge chute to the desired direction. 2. Set the speed selector to the desired forward speed. 3. Fully press and hold the auger control (C, Figure 5) on the right-hand grip to begin auger rotation. To dis-engage the auger, completely release t...

15 Operation DEFLECTOR The distance of the discharged snow is mainly controlledby the position of the deflector (Figure 7). (Engine speedalso affects distance of discharge.) The more the deflector is tilted UP, the farther snow willbe thrown. Loosen the deflector knob, tilt the deflectorUP or DOWN, ...

16 Operation Figure 9. Traction Drive Lock - Disengaged FREE-WHEELING ANDTRACTION DRIVE LOCK For easy turning when pushing the snowthrower, youcan disengage the traction drive at one or both wheelsby using the Traction Lock Pins (See Figures 9 & 10). 1. Turn the unit off, remove the Engine Key, ...

17 Maintenance SCHEDULE CHECK AUGER GEAR CASE LUBRICATION 1. Place the snowthrower on a level surface. 2. Remove the fill plug (Figure 12). 3. Check the lubricant level. It should be level with the lower edge of the plug opening. If not, add SimplicityWinter Weight Worm Gear Oil (available from your...

18 Maintenance Figure 17. Lubricate Deflector Hinges Remove wheels and grease axles once each year. There are two grease fittings on the auger shaft. Wipethe fittings clean and apply grease, using a grease gun.Also apply grease on other points indicated. Apply medium weight (10W) oil to points shown...

19 Storage TEMPORARY STORAGE (30 DAYS OR LESS) Remember, the fuel tank will still contain some gasoline, sonever store the unit indoors or in any other area where fuelvapor could travel to any ignition source. Fuel vapor is alsotoxic if inhaled, so never store the unit in any structure usedfor human...

20 Troubleshooting,Adjustments, & Service WARNING B e f o r e p e r f o r m i n g a n y a d j u s t m e n t o r s e r v i c e t osnowthrower, stop the engine and wait for movingparts to stop. Remove the key. To prevent accidentalstarting, disconnect the spark plug wire and fastenaway from the pl...

21 Troubleshooting PROBLEM POSSIBLE CAUSE REMEDY Auger rotates, but snow is notthrown far enough 1. Chute Deflector too low. 2. Engine speed too slow. 3. Ground speed too fast. 4. Snowthrower discharge chute clogged. 5. Auger belt loose or worn. 1. Adjust deflector as necessary. 2. Set speed to full...

22 Adjustments TRACTION DRIVE SYSTEMADJUSTMENT Speed Selector Pivot Adjustment The Speed Selector is factory set for optimal perfor-mance at each forward and reverse speed setting.However, if drive system components have beenreplaced, adjustment may be necessary. Adjust as follows: 1. Move the groun...

23 Adjustments AUGER DRIVE SYSTEMADJUSTMENTS Auger Drive Clutch Rod Adjustment All auger drive adjustment is accomplished through theauger drive clutch rod. The rod must be adjusted so thatthere is 1/32” clearance between the spring hook and theauger lever (see Figure 20). Proper adjustment allowsth...

24 Adjustment DISCHARGE CHUTE PINIONADJUSTMENT If the discharge chute is difficult to operate, first lubricatethe pinion gear (A, Figure 21) and ring gear (F). If it isstill difficult to operate, adjust as follows: 1. Loosen the nut (G, Figure 21) which holds the pinion gear bracket in the slotted h...

25 Service Figure 25. Belts and PulleysA. Capscrews F. Auger Pulley B. Belt Guides G. Idler Pulley, Auger C. Traction Drive Belt H. Traction Pulley D. Auger Drive Belt I. Idler Pulley, Traction E. Engine Pulley Figure 24. Auger Pulley Belt Stops (shown with bottom cover removed) A. Nuts C. Auger Pul...

26 Service Figure 26. Belt Pattern (as viewed from front ofsnowthrower)A. Engine Pulley C. Idler Pulley B. Drive Belt D. Driven Pulley Figure 27. Shear Pins SHEAR PIN REPLACEMENT Under most circumstances, if the auger strikes an objectwhich could cause damage to the unit, the shear pin willbreak. Th...

27 Specifications Specifications are correct at the time of printing and are subject to change without notice. ENGINE: 8 HP* Tecumseh Make Tecumseh Model Snow King Horsepower 8 @ 3600 rpm Displacement 19.43 Cu. in (318.3 cc) Oil Capacity See Engine Owner’s Manual 9 HP* Briggs & Stratton Make Bri...

28 Replacement Parts & Accessories REPLACEMENT PARTS Replacement parts are available from your authorizeddealer. Always use genuine Simplicity Service Parts. TECHNICAL MANUALS Additional copies of this manual are available, as well asfully illustrated parts lists. These manuals show all of thepr...