Shure SE30-2 - Manuals - manualsarea.com

Page 2 - Table of Contents; W A R N I N G; T o r e d u c e t h e r i s k o f f i r e o r e l e c t r i c s h o c k , d o n o t

Table of Contents W A R N I N G T o r e d u c e t h e r i s k o f f i r e o r e l e c t r i c s h o c k , d o n o t e x p o s e t h i s a p p l i a n c e t o r a i n o r e x t r e m e m o i s t u r e .

Page 3 - SPECIFICATIONS

DESCRIPTION The Shure Model SE30* Gated Compressor/Mixer is a high-quality gated memory compressor combined with a s e l f - c o n t a i n e d , p o r t a b l e , t h r e e - i n p u t m i x e r a n d r e m o t ea m p l i f i e r d e s i g n e d s p e c i f i c a l l y f o r p r o f e s s i o n a l ...

Page 7 - GENERAL OPERATION; Automatic Switchover:

(25) AC Power Receptacle: Special internationally ac- cepted connector for detachable ac line cord, three-wire with safety ground pin. (26) 30 Volts DC Jacks: May be used for powering the unit from an external 30 ± 20% dc source, or for powering external equipment (up to 5 ma) from the batteries or ...

Page 8 - TYPICAL SET-UP AND OPERATION; OPERATING CONSIDERATIONS; LARGE CHANGES IN INPUT LEVEL

GENERAL OPERATION (Cont’d) The “Tip” connection of the headphone plug will be in phase with Pin 3 of all Input (13) and Output (16) connec- tors, and with the tip of the Mix Bus jack (12). TYPICAL SET-UP AND OPERATION A typical set-up and operation procedure is described for remote amplifier applica...

Page 9 - THEORY OF OPERATION

OPERATING CONSIDERATIONS (Cont’d) conference or conversation situation, with several micro- phones “live” but only one speaker talking at a time, eachInput control should be set so that each speaker results in approximately the same amount of compression, observingthat the overall level is correct f...

Page 11 - GATED MEMORY

THEORY OF OPERATION (Cont’d) maximum of 30 dB, the second potentiometer section acts as a conventional voltage divider output attenuator for lowcontrol settings. The input transformers increase the signal voltage by 21 dB. Input 1 has a second line input, phone jack J12, which operates only in the L...

Page 16 - SCHEMATIC DIAGRAM; P I N C O N N E C T I O N S -

SCHEMATIC DIAGRAM INTEGRATED CIRCUIT MC201 AND MC301 FIGURE 4E REPLACEMENT PARTS FOR SE30-TABLE 1 P I N C O N N E C T I O N S - TOP VIEW NOTE: THE COMMECIAL ALTERNATES SHOWN ABOVE ARE NOT NECESSARILY EQUIVALENTS, BUT MAY BE USED IN THE EVENT THAT DIRECT FACTORY REPLACEMENTS ARE NOT IMMEDIATELY AVAIL...

Page 20 - NOTES TO SCHEMATIC DIAGRAM AND

TEST VOLTAGES, INTEGRATED CIRCUITS TABLE 1C NOTES TO SCHEMATIC DIAGRAM AND TEST VOLTAGES (Figure 4, Table 2) 1. All capacitors shown in microfarads and 50 volts or more unless otherwise indicated. Electrolytic capac- itors shown in mF X volts. pF = picofarad. 2. All fixed resistors ±10%, ¼ watt unle...

Page 25 - SERVICE INSTRUCTIONS; COVER REMOVAL AND REPLACEMENT

SERVICE INSTRUCTIONS The SE30 Gated Compressor/Mixer uses components of the highest quality, operating well within their ratings to assure long life and excellent stability. No routine main-tenance is necessary with the exception of battery re- placement. CAUTION: There are no user serviceable parts...

Page 26 - board; CALIBRATION

S E R V I C E I N S T R U C T I O N S ( C o n t ’ d ) 3 . 4 . 5. 6 . 7. 8 . 2 6 push-on retainers so that it may be raised above the chassis for service without complete removal. With all power turned off, depress retainer locking tab, if any, and pry each corner of the board from its retainers. Lif...

Page 27 - GATED MEMORY CALIBRATION:

S E R V I C E I N S T R U C T I O N S ( C o n t ’ d ) PROCEDURE: First, the meter (7) must be mechanically set to zero. Turn the Power switch (11) OFF and wait one minute. The meter pointer should rest over the mark at the left-hand end of the scale, left of the -20 VU and 0 dB Compressionline. Usin...

Page 28 - STEREO SYNCHRONIZATION

SERVICE INSTRUCTIONS (Cont’d) C. Set the Meter switch (8) to VU and the VU Range switch (4) to +4. Adjust VU CAL trimmer poten- tiometer (R529) for a 0 VU meter reading. Cali- bration is complete. STEREO SYNCHRONIZATION Two SE30’s may be synchronized to operate together for two-channel stereo applic...

Page 29 - MODIFICATIONS

MODIFICATIONS Noise Improvement for Single Inputs: The overall signal-to-noise ratio of the SE30 may be im- proved for single-input applications by disabling the two unused input channels. This automatically reduces the noise level of the mixing circuitry without changing the gain or other character...

Page 30 - M O D E L A 1 0 0 A C A R R Y I N G H A N D L E A S S E M B L Y; To position; MODEL A100B RACK PANEL; FIGURE 2; CARRYING HANDLE ASSEMBLY; FIGURE 1

M O D E L A 1 0 0 A C A R R Y I N G H A N D L E A S S E M B L Y The Shure Model A100A Carrying Handle Assembly provides a means for conveniently carrying the Shure M o d e l S E 3 0 G a t e d C o m p r e s s o r / M i x e r . T h e M o d e l A100A serves as a handle for carrying the SE30, as a cover...