Shure E3 - Manuals - manualsarea.com

Page 2 - USING THIS SYSTEM AT EXCESSIVE VOLUMES; hour; 20 dB SPL - avoid or hearing damage may occur

©2006, Shure Incorporated 1 Printed in U.S.A 27D8791 (Rev. 9) ENGLISH It is difficult to measure the exact Sound Pressure Levels (SPL) present at the eardrum, since the SPL in the ear is affected by ambient sound from floor wedges or other devices in addition to the volume setting on the PSM. The is...

Page 3 - EARPHONE FEATURES

2 ENGLISH EARPHONE FEATURES The Shure E Series earphones are designed for use with Shure Personal Monitor Systems. They are also ideally suited for use with CD players, MP3 players, notebook computers and any other listening device that has a 3.5 mm ( 1 / 8 -inch) stereo output. 4 = Model has listed...

Page 4 - EARPHONE COMPONENTS; Sleeve Varieties

3 ENGLISH EARPHONE COMPONENTS The earphone components are illustrated below, using the E2 model as an example. Ear-phone shapes vary, depending on the model. Earphones: When properly inserted in the ear, the Shure logo will appear right-side up on the outside of the earphone with the cable exit poin...

Page 5 - INSERTING THE EARPHONES; Flex sleeves

4 ENGLISH INSERTING THE EARPHONES The quality of both the frequency response and the sound isolation depend on how well the earphone sleeve seals the ear canal. If the earphone seems to be lacking in low frequency response, try one of the other sleeve options to obtain a better seal. 2. E2 and E3: w...

Page 6 - ENGLISH; CONNECTING TO A BODY PACK; Slowly raise the volume to a comfortable listening level.; SLEEVE VARIETIES; Wax Guard; Always turn the volume down before plugging the earphones into a

5 ENGLISH CONNECTING TO A BODY PACK 1. Turn down the volume of your listening device.2. Connect the 3.5 mm ( 1 / 8 -inch) plug into the earphone output jack. 3. Insert earphones into your ears (see previous page). 4. Slowly raise the volume to a comfortable listening level. SLEEVE VARIETIES Your ear...

Page 7 - CHANGING SLEEVES

6 ENGLISH CHANGING SLEEVES The sleeves at the end of the earphones can be replaced by sliding them off and on. A com-bination of twisting and pulling is recommended for sleeve removal. NOTE: On each foam sleeve there is a rough side and a smooth side. For greater com- fort, Shure recommends that you...

Page 8 - CARE AND CLEANING; Follow these tips to prevent service costs and ear infections:

7 ENGLISH CARE AND CLEANING Follow these tips to prevent service costs and ear infections: • Avoid getting moisture in the nozzle, as this can adversely affect sound quality. Sweat entering the nozzle may cause the earphone to temporarily stop working. However, normal operation often returns after t...

Page 10 - To place a wax guard on one of your E2 earphones:; FIGURE 2: E2 Wax Guard Installation; Do not place wax guards on sleeves! Wax guards are

9 ENGLISH WAX GUARD You should place wax guards on the nozzle of your E2 earphones before using them. These protective rings are found on an adhesive strip in the fit kit that comes with your earphones. To place a wax guard on one of your E2 earphones: 1. Remove the sleeve from the earphone nozzle.2...

Page 11 - SPECIFICATIONS; Transducer Type; Dynamic; Output Connector

10 ENGLISH SPECIFICATIONS CERTIFICATION Eligible to bear CE marking. Conforms to European EMC Directive 89/336/EEC. Meets ap-plicable tests and performance criteria in European Standard EN 55103 (1996) Parts 1 and 2, for residential (E1) and light industrial (E2) environments. FURNISHED ACCESSORIES ...

Page 12 - OPTIONAL ACCESSORIES

11 ENGLISH OPTIONAL ACCESSORIES E3/E5 Earphones: Bag of 20 foam sleeves.............................................................................PA750Bag of 500 foam sleeves...........................................................................PA754Bag of 10 clear flex sleeves (small) ..........

Page 13 - CUSTOM EAR MOLDS

12 ENGLISH CUSTOM EAR MOLDS A Hearing Health Care Professional can make custom-fit ear molds for the E3 from im-pressions of your ears. Custom-made ear molds can provide better comfort and ambient noise isolation for some users. The E3 fits in a custom ear mold as shown in the following illustration...