Shure Conference Phone - Manuals

Shure Conference Phone – Manual in PDF format online.

Manuals:

Manual

Manual Shure Conference Phone

Summary

Page 2 - CONTENT; User Guide; Conference; ONE; Discussion System with IntelliMix

English 1. READ these instructions.2. KEEP these instructions.3. HEED all warnings.4. FOLLOW all instructions.5. DO NOT use this apparatus near water.6. CLEAN ONLY with dry cloth.7. DO NOT block any ventilation openings. Install in accordance withthe manufacturer’s instructions.8. Do not install nea...

Page 3 - Introduction

1 Introduction The Shure’s Conference ONE ™i Discussion System is extremely easy to install and use. It was developed for use at conferences, meetings, platform discussions and other comparable applications. Due to its integrated loudspeakers, the Conference ONE ™i Discussion System also functions a...

Page 4 - Description

2 Description 2.1 Power Supply Unit C1-PS 60i The power supply unit C1-PS 60i supplies the consoles with power and serves as an interface to externaldevices. Front view 2 3 3 7 4 1 5 6 2 Daisy chain socket Minicon socket connecting the consoles viabus cables. Audio output The ON/OFF button activates...

Page 5 - Input level + Phantom power switch

IntelliMix ® Link input Socket for connection of a Shure SCMseries automatic mixer. Please note thatthe audio signal only flows from the SCMseries mixers into the Conference ONE ™ Discussion System and not from theDiscussion System into the connectedSCM series mixers. 7 2 4 Power socket Socket with ...

Page 8 - Headphone volume control; Headphone socket; Setting Up

3 7 Headphone volume control Adjusts the headphone volume. Headphone socket 1/8” stereo headphone socket. The console speaker switches off when youconnect headphones. CAUTION: Use only stereo plugs! Daisy chain sockets Minicon socket for connection and through-connection of the console bus. The sock...

Page 9 - Possible Configurations

3 8 3.2 Possible Configurations For small systems, up to 15 consoles can be connected directly to the Minicon socket on the front of thepower supply unit. The bus cable is connected from each console to the next. Larger systems with more than 15 consoles or in systems where the first console is more...

Page 10 - System Settings; Power Supply Unit

4 9 4 System Settings All adjustments to the settings of the conference system are made on the chairman console. The controlslocated on the power supply unit adjust signal input and output for external devices. 4.1 Power Supply Unit The slide switch beside the input socket on the rear of the powersu...

Page 11 - Chairman Console

4 10 4.2 Chairman Console The system is configured from the chairman's consolewith the aid of the LCD and the three buttons below it:SELECT, and . 4.2.1 Status Page In normal operating mode, the display shows the status page with the current settings. The display alwaysreturns automatically to this ...

Page 13 - Language Selection

4 12 4.3 Test Mode Activate test mode by pressing and holding both of the and buttons for approximately three seconds. The installed software version appears in the display andthe lighted rings on all delegate consoles illuminate inorder to permit simple detection of any cable breakage or defective ...

Page 14 - AEC / Telco Audio Interface; Interface Levels; External Interface Device Settings

English 5 AEC / Telco Audio Interface This interface provides a dedicated termination to connect the discussion system directly to most externaltelephone hybrids or videoconference codecs, enabling users of the system to communicate with remoteparties. When used in conjunction with a telephone hybri...

Page 15 - System Operation

English 6 System Operation The Conference ONE ™i Discussion System can be operated in either of the two operating modes described below. 6.1 Manual Mode In manual mode, each console microphone is activated by simply pressing the PTT button and deactivatedby pressing this button again. However, the n...

Page 16 - Operating Instructions

English 6 15 6.3 Operating Instructions To set the volume of the system: 1. Press or button to change the volume 2. Press SELECT to return to the Status Page To select Operating mode: 1. Press SELECT to access the Setup menu 2. Press or button until the Mode menu is underlined in the display 3. Pres...

Page 17 - Troubleshooting; Problem

English 7 16 Green Power LED is off • Is the power cable plugged in?• Is the power switch set to ON (I)?• Check the main fuse in the power socket. Red Protect LED illuminates • Check that the maximum permissible number of consoles has not been exceeded (60). • Disconnect all consoles and cables. If ...

Page 18 - Technical Data; Power supply unit C1-PS 60i

Output Clipping Level Impendance English 8 17 8 Technical Data Power supply unit C1-PS 60i Mains voltage C1-PS 60i A: 120 V AC, 50/60 Hz C1-PS 60i J: 100 V AC, 50/60 Hz C1-PS 60i E, C1-PS 60i UK : 220 - 240 V AC, 50/60 Hz Power rating: 330 VA Primary Fuses C1-PS 60i A: T4A C1-PS 60i J: T5A C1-PS 60i...

Page 19 - Consoles; Performance

Consoles Power rating Delegate console C1-Di: 1,7 W Chairman console C1-Ci: 5,3 W Microphone Microphone type: Electret-condenser (Microflex ® ) Directional characteristic: Supercardioid Headphone output Output impedance: 4 Ohm Socket: 1/8” stereo jack socket Performance Microphone to audio output Fr...

Page 21 - Appendix A – Connector Pin Assignments

English Pin Signal Cable Color Code 1 Audio 1 black 2 Control 2 blue 3 -24 V gray 4 GND brown 5 GND purple 6 GND red/gray 7 GND red 8 +24 V pink 9 Control 3 yellow 10 Control 1 green 11 Mic Bus white 12 Mode red/blue Pin Signal 1 n.c. 2 TXD 3 RXD 4 n.c. 5 GND 6 n.c. 7 n.c. 8 n.c. 9 n.c. 9 20 9 Appen...

Page 24 - Get commands

English 21 h 01 h to 1E h 22 h 01 h to 1E h 23 h 24 h 25 h XX h 10 23 Get commands Report from power supply 00 h 01 h 00 h 01 h Report the input level,01 h =mute 1E h =highest level Report the output level,01 h =mute 1E h =highest level Report: input switch is offReport: input switch is on Report: o...