Sharp R-501CW- Manuals

Page 2 - DISPLAY SIDE

LCD Modules LS013B4DN04 2 Application Note MECHANICAL SPECIFICATIONS External Dimensions PARAMETER SPECIFICATION UNIT Screen Size 1.3 Inch Viewing Area 24.192 (H) × 24.192 (V) mm Dot Configuration (Square panel) 96 (H) × 96 (V) Dots Dot Pitch 0.252 (H) × 0.252 (V) mm Pixel Array Stripe Array - Exter...

Page 3 - Connector Specifications; Connector Bending Specifications

LS013B4DN04 LCD Modules Application Note 3 Connector Specifications NOTES:1. EXTCOMIN is HIGH enabled. When LOW, the serial input flag is enabled. See Figure 14 and Figure 15 for recommended circuits.2. DISP enables/disables the display. All pixels will revert to Normal mode (reflective) when LOW. W...

Page 8 - SIGNAL DESCRIPTIONS

LCD Modules LS013B4DN04 8 Application Note SIGNAL DESCRIPTIONS Input signal characteristics are given in Table 2 and Table 3; refer to Figure 8 for timing diagrams. A l l m e a s u r e m e n t s a r e a t V D D A = + 5 . 0 V , VDD = +5.0 V, GND = 0 V, Ta = 25°C. NOTES:1. Dynamic Mode (continuously u...

Page 9 - Timing Diagrams; EXTCOMIN Signal

LS013B4DN04 LCD Modules Application Note 9 Timing Diagrams Figure 8. SCS, SI, SCLK, EXTCOMIN, and DISP Signals SCS SCS, SI, SCLK Signal EXTCOMIN Signal DISP Signal trSCS trSI tfSI twSCLKH twSCLKL twEXTCOMINH ƒEXTCOMIN tsSI trSCLK trDISP tfSCLK twSCSH twSCSL tfSCS thSCS tfDISP trEXTCOMIN EXTCOMIN DIS...

Page 12 - Static Mode

LCD Modules LS013B4DN04 12 Application Note Static Mode Static Mode is the module’s lowest-power mode, with data latches and other circuitry powered down.Static Mode can be held indefinitely; as long as thepanel has power and VCOM is toggled periodically. Sharp recommends keeping maximum time betwee...

Page 13 - VCOM Inversion

LS013B4DN04 LCD Modules Application Note 13 VCOM Inversion Periodic VCOM inversion impresses a periodic polarity inversion across the panel to keep a latentcharge from building up within the Liquid Crystal cell. Itcan be implemented either through software or throughhardware. In either implementatio...

Page 15 - DESIGN NOTES

LS013B4DN04 LCD Modules Application Note 15 DESIGN NOTES 1. This device is static sensitive. Handle it only in astatic-safe environment. 2. Do not press on the surface of the module, and donot stack modules in such a way that pressure willbe applied to the surfaces or to the connector area.The safes...

Page 16 - BACK SIDE

LCD Modules LS013B4DN04 16 Application Note HANDLING, STORAGE, AND PACKAGING 1. This module is not made to be disassembled.Doing so may cause permanent damage. 2. The liquid crystal material in this module is injurious tohumans. Do not allow it to get into the eyes or mouth.If any liquid crystal mat...

Page 17 - Packaging Diagrams

LS013B4DN04 LCD Modules Application Note 17 Packaging Diagrams Stack no more than 12 cartons high. Product is packed in lots of 800. Figure 22. Packaging Format LS013B4DN04-23 Figure 23. Package Labeling LS013B4DN04-24

Page 19 - LCD Modules; SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

LS013B4DN04 LCD Modules ©2011 by SHARP Corporation Reference Code SMA11008 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP’s product warranty....

Manuals:

User Manual Sharp R-501CW

Summary

Sharp Manuals