Sharp MX-2314N - Manuals - manualsarea.com

Page 2 - A. Transportation space; Strictly observe the following specifications.; Power capacity; Current capacity; Power voltage; The frequency must be within the range of the specified frequency; Safety; Be sure to properly ground the machine.; Power plug; D. Floor strength and level; Do not install the machine near a heater, a cooler, or a humidifier.; Content

MX-3114N Transit, Installation (using) environment, Note - i MX-3114N 6HUYLFH0DQXDO Transit, Installation (using) environment, Note 1. Installing (use) conditions Before installing the machine, check that the following installing(use) conditions are satisfied. If the installing (use) conditions are ...

Page 3 - Operational environment; Contaminates; F. Note for handling PWB and electronic parts

MX-3114N Transit, Installation (using) environment, Note - ii Operational environment Temperature: 10 to 35 q C Humidity: 20 to 85% RH Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m) (2) Contaminates If dust enters the machine, it may cause dirty copy and a paperjam, resulting in a shor...

Page 4 - transfer unit handling; Drum unit; Transit and delivery; Model name

MX-3114N Transit, Installation (using) environment, Note - iii G. Note for proper drum, developing, fusing and transfer unit handling When handling the OPC drum, developing and transfer units,observe the following items. Drum unit • To prevent damage to the OPC drum, avoid working on the drum unit i...

Page 5 - Tray rotation plate lock release; Name

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 1 MX-3114N 6HUYLFH0DQXDO [2] MX-2314N/2614N/3114N (MAIN UNIT) 1. Unpacking A. Unpacking B. Fixing tape and protection material removal 26cpm/31cpm machine C. Packed items check * Depending on the country D. Lock release (1) Tray rotation plate lock relea...

Page 6 - A. Developer installation; Open the cover to remove.

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 2 2. Installation When an optional paper feed desk is connected to the machine,unpack and install the paper feed desk, then unpack the machine.Place the machine on the option desk securely, and perform theinstalling procedures of the machine.Place the ma...

Page 8 - After entering the simulation, close the front cabinet.

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 4 When installing the machine, there is no need to remove orinstall the OPC drum unit. If it must be removed or installed forany reason, follow the procedures below. When removing orinstalling the OPC drum unit, put your hand from below the unitand slide...

Page 9 - Color toner cartridge positions; Cleaning of LSU's dust-proof glass and PTC wire; Detach the LSU cleaning bar from the front cover.

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 5 9) Open the front cabinet, and insert each toner cartridge. Be sure to install the color cartridges to their proper positions.Avoid installation to a different color position. Do not forcibly insert the toner cartridge. Push it in until the cartridge i...

Page 10 - Close the front cabinet.; D. Paper feed tray setup; System setting; Pull out the paper tray.; Item

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 6 4) Move the PTC cleaning rod back and forth a few times to cleanthe PTC wire. After completion of cleaning, insert the cleaning rod completelyto the bottom. 5) Return the LSU cleaning rod to the front cabinet so that the feltfaces upward. Fit the boss,...

Page 11 - E. Specifications setup; Use simulation 26-6 to set the machines destination.; Image quality check; Execute the following items.

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 7 E. Specifications setup Use simulation 26-6 to set the machines destination. After completion of destination settings, change the set values tocustomize the following settings. 3. Image quality check A. Execution items Execute the following items. *1: ...

Page 13 - In this case, check each drive section and the process section.; Copy color balance and density check; * Execute the high density image correction (Process correction); Method 1; In addition, be sure to use the specified paper for color.

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 9 5) If the display of ALL_ROTATE is NG, turn all the LSU skewadjustment screws to adjust, and perform the procedures 2) to4). Repeat the procedures 2) to 5) until the display ofALL_ROTATE becomes OK. If the display of ALL_ROTATE isOK, go to the procedur...

Page 16 - Printer color balance/density check; Execute SIM 64-5 to print the print test pattern.; Method 2; The density level of each color must be almost at the same level.; PRINTER CALIBRATION

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 12 Method 2 Use SIM46-21 to print the color balance adjustment sheet, andcheck each process (CMY) black patch color balance and the blackpatch in order to confirm that the color balance adjustment isproper. If the color balance of each patch of the proce...

Page 18 - The half tone image correction is performed.

MX-3114N MX-2314N/2614N/3114N (MAIN UNIT) 2 – 14 6) Set the color patch image (adjustment pattern) printed in theprocedure 5) on the document table. Set the color patch image (adjustment pattern) printed in theprocedure 2) on the document table. Place the color patchimage so that the fine lines are ...