Sharp LED TV - Manuals

4 Introduction • Do not place vases or any other water-filled containers on thisproduct.The water may spill onto the productcausing fire or electric shock. • Stand — Do not place the product on an unstable cart, stand, tripodor table. Doing so can cause theproduct to fall, resulting in seriousperson...

5 Introduction 3D Glasses Prevention of accidental ingestion • Keep the accessory out of the reach of small children. Small children can accidentally swallow these parts. – If a child accidentally swallows any of these parts, seek immediate medical attention. Do not disassemble • Do not disassemble ...

6 Supplied accessories Introduction Remote control unit ( x 1) “AAA” size battery ( x 2) AV cable ( x 1) Pages 10 and 13 Page 10 Page 30 Optional accessories Some of the listed optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorised Dealer f...

7 Protection against overturning There is a danger of the product overturning in the case of a disaster or sudden collision. Carry out the following tip-resistant measurement for your safety. Anchoring the TV to the wall or a pillar 1 Affix the TV to the wall or a pillar usingextra strong ties and c...

8 Preparation Attaching the Stand • Before attaching (or detaching) the stand, unplug the AC cord.• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged. CAUTION • Be sure to follow the instructions. Incorrect installation of the stand...

9 Preparation Connecting the TV Notes on installing the TV • Avoid direct sunlight and place the TV in a well-ventilated location. • Place the TV in a level location.• Do not turn on the power of the TV before connecting the AC cord. p n o *  Plug the standard DIN45325 plug (IEC 169-2) 75-ohm coaxi...

10 Using the remote control unit Inserting the batteries Before using the TV for the first time, insert two supplied “AAA” size batteries. When the batteries become depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries. 1 Open the battery cover. 2...

11 TV (front view) 3D infrared emitter *1 Remote control sensor OPC sensor *2 POWER button MENU button INPUT button Channel buttons ( CH r / s ) Volume buttons ( VOL +/–) Center Icon Illumination *1 This panel emits infrared signal towards the 3D glasses you wear when viewing 3D images. Do not place...

12 TV (rear view) — continued C.I. SD/ SDHC USB 1 AUDIO(L/R) (DC 5V 900mA) ARC OUTPUT DIGITAL AUDIO OUTPUT USB 2 AUDIO IN (HDMI 2/PC) AV INAUDIO (L/R) INPUT 5 SD/SDHC card slot OUTPUT (Headphones/ AUDIO (L/R)) terminal* 1 USB 1 port HDMI 3 (HDMI/ARC) terminal (INPUT 3) HDMI 2 (HDMI) terminal (INPUT ...

13 Part names and functions Remote control unit EXT MEDIA TV INFO MENU GUIDE SLEEP 5 6 15 16 2 1112 8 9 10 7 1 27 28 13 4 17 * 18 14 25 26 2223 20 19 21 24 3 1 < (Standby/On) To switch the power on and off (Page 18). 2 EXT MEDIA buttons AQUOS LINKIf external equipment such as a AQUOS BD player is...

14 Quick guide Inserting the CA card into the CI module In order to receive coded digital stations, a common interface module (CI module) and a CA card must be inserted in the CI slot of the TV. 1 Carefully insert the CI module in the CI slot with the contact side forward. 2 The logo on the CI modul...

15 What is the HOME? You can easily launch to enjoy Internet connection and Home network function and to perform settings for the TV from this “HOME” screen.By connecting the TV to the internet you can enjoy a variety of broadband content. Internet browsing on a TV behaves differently to a PC (Perso...

16 Quick guide Using software keyboard Use the software keyboard when you need to input text. Char.Set Caps Cancel Done Delete Clear Cursor Left Caps Char.Set Cursor Right 1 Char. Set Changes character set into the alphabet, numbers, symbols, etc. 2 Caps Changes characters to capital/lower case. 3 D...

17 Initial auto installation When the TV is powered on for the first time after purchase, the initial auto installation wizard appears. Follow the menus and make the necessary settings one after another. Confirm the following before turning on the power E Is the antenna cable connected? E Is the AC ...

18 Daily operation Turning on/off the power – using the control panel of the TV Turning on/off the power 1 Turn on the power. Press < on the TV (after a few seconds, an image appears with sound). • Wait more than five seconds until you press < on the TV after inserting the power plug. 2 Turn o...

19 Watching TV (DTV only) Press > to change “DTV” or “ATV”. NOTE • When watching Digital Radio or Data broadcasting, the image is switched to DTV. • When watching external video source, the image is switched to ATV or DTV, which was watched lastly. CH list You can check the CH list and view detai...

20 Switching the digital audio format (DTV only) If multi sound modes are received, each time you press MPX the mode switches as follows. Audio (ENG) STEREO L/R L R LR CH A CH B CH AB Audio (ENG) CH A Audio (ENG) MONO Press c / d to select L or R sound when the STEREO or DUAL MONO screen is displaye...

21 Watching TV Favourite Channel Information Before installation This function allows you to group your favourite channels in a separate list. Pre-setting “My favourite” in advance allows you to select your favourite channels more conveniently. NOTE • “My Favourite” can only be used for DTV mode.• T...

22 Teletext What is teletext? Teletext broadcasts pages of information and entertainment to specially equipped TV. Your TV receives teletext signals broadcast by a TV network, and decodes them into graphical format for viewing. News, weather and sports information, stock exchange prices and programm...

23 View setting Initial teletext page (DTV only) If you set the language of the initial page (this page is displayed for the first time after pressing m ) for teletext in DTV mode, it will start from the selected language page. 1 Go to “HOME” > “TV Menu” > “Setup” > “Viewsetting” > “Indi...

24 Watching TV EPG (DTV only) EPG is a programme list that is displayed on the screen. With the EPG, you can check the schedule of DTV/RADIO/DATA, view detailed information about them, tune to an event currently on-air. Useful settings for using EPG Basic setting View setting EPG If you want to use ...

25 Selecting a programme using EPG (DTV only) Basic operation E Display the EPG screen Press GUIDE . GUIDE EPG 001 20 21 22 23 0 1 : Select : Enter : Back : Exit Programme info. Search by genre Search by date Timer list [Fri] 1/4 20:00 Today [Sat]2 [Sun]3 [Mon]4 [Tue]5 [Wed]6 [Thu]7 [Fri]8 EPG [DTV-...

26 4 Search a programme in a category 1 Press G . 2 Press a / b to select the desired genre, and then press ? . 3 Press a / b to select a programme you want to watch, and then press ? . EPG [DTV-TV] [Fri] 1/4 20:00 Today [Sat]2 [Sun]3 [Mon]4 [Tue]5 [Wed]6 [Thu]7 [Fri]8 Back to EPG : Select : Enter :...

27 Watching TV Timer setup using EPG The TV can be switched to a programme or start recording for USB-recording at the set time. 1 Press GUIDE . 2 Press a / b / c / d to select the programme you want to set, and then press ? . 3 Press c / d to select “Watch” or “Record”, and then press ? . • If you ...

28 E Before connecting ... • Be sure to turn off the TV and any devices before making any connections.• Firmly connect a cable to a terminal or terminals.• Carefully read the operation manual of each external device for possible connection types. This also helps you get the best possible audiovisual...

29 Connecting external devices Video connections HDMI connection Example of connectable devices E DVD player/recorder E Blu-ray player/recorder E Game console The HDMI connections permit digital video and audio transmission via a connection cable from a player/recorder. The digital picture and sound...

30 Connecting external devices Y P B ( C B) P R ( C R) Component connection Example of connectable devices E VCR E DVD player/recorder You will enjoy accurate colour reproduction and high quality images through the INPUT 6 terminal when connecting a DVD player/recorder or other device. 6 n o INPUT 6...

31 Audio connections Speaker/amplifier connection Connect an amplifier with external speakers as shown below. E Connecting an amplifier with digital/analogue audio inputs n o DIGITAL AUDIO OUTPUT AUDIO(L/R) OUTPUT  Optical audio cable (for digital audio) (commercially available)  Stereo conversion...

32 AQUOS LINK Controlling HDMI devices using AQUOS LINK E What is AQUOS LINK? Using the HDMI CEC protocol, with AQUOS LINK you can interactively operate compatible system devices (AV amplifier, DVD player/recorder, Blu-ray player/recorder) using a single remote control unit.By connecting AQUOS LINK-...

33 AQUOS LINK connection First connect the AQUOS AUDIO speaker system or an AQUOS BD player/AQUOS recorder that supports the HDMI CEC protocol. NOTE • Refer to the operation manual of the device to be connected for further details.• After unplugging connection cables or changing the connection patte...

34 AQUOS LINK Operating an AQUOS LINK device AQUOS LINK allows you to operate the HDMI-connected device with a single remote control unit. EXT MEDIA Use the following procedure to start playback. 1 Press I to start playback of a title. • See the section Top menu/title list if you want to start playb...

35 AQUOS LINK AQUOS LINK control Set to “On” to enable HDMI CEC functions. Auto power on If this is activated, the one touch play function is enabled. While the TV is in standby mode, it automatically turns on and plays back the image from the HDMI source. • The factory default for this item is “Off...

36 MENU MENU E Auto power on When an MHL-compatible device is connected to the TV, the TV turns on automatically. • This function operates when “AQUOS LINK control” is set to “On”. (See page 35.) E Auto input selection When an MHL-compatible device is connected while the TV is on, the input mode is ...

37 Picture settings Go to “HOME” > “TV Menu” > “Setup” > “Picture”. Setup AV mode Picture OPC [Off] Clear Picture Processing [Middle] [STANDARD] [STANDARD] CH list :Back :Enter Menu Backlight : Select NOTE • After selecting a menu such as “AV mode”, “Clear Picture Processing”, “OPC”, “Backl...

38 Picture Picture adjustments Adjusts the picture to your preference with the following picture settings. Adjustment items Selectable items c (Cursor) d (Cursor) Backlight The screen dims The screen brightens Contrast For less contrast For more contrast Brightness For less brightness For more brigh...

39 Active contrast Automatically adjusts the contrast of an image according to the scene. (“Advanced”, “Standard”, “Off”). NOTE • “Active contrast” is not available in case of 4K input. DNR (Digital Noise Reduction) “DNR” produces a clearer image (“Auto”, “High”, “Middle”, “Low”, “Off”). NOTE • This...

40 Audio Surround This function produces a surround effect from the speakers. Item 3D Stadium Reproducing lifelike experience of excitements such that live sports or concert performances in a stadium create. 3D Hall Reproduces a concert hall experience with realistic live surround sound based on rev...

41 Power save settings Go to “HOME” > “TV Menu” > “Setup” > “ECO”. Setup No signal off ECO picture control ECO Energy save CH list Menu No operation off [Disable] [Disable] [Off] [On] :Back :Enter : Select NOTE • You can also select “ECO” by pressing ECO . ECO ECO picture control This funct...

42 Channel settings Go to “HOME” > “TV Menu” > “Setup” > “View setting”. Setup Network setup Auto installation View setting Channel settings CH list Menu Bluetooth setup :Back :Enter : Select View setting Auto installation The TV automatically detects and stores all available services in yo...

43 Basic adjustment Buttons for “Manual adjust” operation Lock Press R button. When the service is locked, you must enter your password whenever you tune to the service. CH skip Press G button. Services with a ✔ mark are passed over when pressing CH r / s on the TV or remote control unit. Delete Pre...

44 Label When a TV channel sends its network name, the “Auto installation” detects the information and assigns a name to it. However, you can change channel names individually. Select each character of the new name for the channel with using the software keyboard (see page 16). NOTE • The name can b...

45 Individual setting – Password View setting Password Allows you to use a password to protect certain settings from being accidentally changed. Go to “HOME” > “TV Menu” > “Setup” > “View setting” > “Individual setting” > “Password” . E Setting a password Register a four-digit passwor...

46 Individual setting – Time View setting Clock setup Go to “HOME” > “TV Menu” > “Setup” > “View setting” > “Individual setting” > “Clock setup”. Time adjustment This function allows you to set the clock manually. NOTE • If you select “No”, the TV will try to get the time for the broa...

47 Optional features settings Go to “HOME” > “TV Menu” > “Setup” > “Option”. Setup Option for view Option 3D setup CH list Menu Terminal setting EPG setup :Back :Enter : Select Selecting the picture size manually Option Wide mode You can select the picture size. Selectable picture size vari...

48 Option 4:3 mode (DTV only) The 4:3 mode allows you to select between “Full” and “Normal”. Go to “HOME” > “TV Menu” > “Setup” > “Option” > “4:3 mode”. Item Full Wide image without side bars. Normal Normal range keeping 4:3 or 16:9 aspect ratio. 4:3 screen types 4:3 mode “Full” 4:3 mode...

49 Option Input label You can label each input source with a custom description. 1 Press b to select the desired input source from the “INPUT” menu, and then press ? . 2 Go to “HOME” > “TV Menu” > “Setup” > “Option”> “Terminal setting” > “Input label”. 3 Press ? to display the softwar...

50 Option Headphone out setting You can select the headphone/speaker audio output when using the headphones. Go to “HOME” > “TV Menu” > “Setup” > “Option” > “Terminal setting” > “Headphone out setting”. Item Headphone Audio output from headphones only. Dual Audio output from headphone...

51 Option Wallpaper setting This function is available only when “Quick start” is set to “On (Wallpaper)”.Activating the function will display still images when the TV is in standby mode. Go to “HOME” > “TV Menu” > “Setup” > “Option” > “Wallpaper setting”. Data source For the wallpaper, ...

52 Option Key lock This function allows you to lock the buttons on the TV or remote control unit in order to prohibit children from changing the channel or volume. Go to “Home” > “TV Menu” > “Setup” > “Option” > “Key lock”. Item Off Unlocks the buttons. RC control lock Locks all buttons ...

53 Miracast setup By Miracast technology you can enjoy the contents ofMiracast compatible smartphone or tablet to this TV. Using the Miracast device When you connect a device such as a Miracastcompatible smartphone or tablet to this TV, you canenjoy video and audio from the device on the TV'slarge s...

54 Playing Back Files from a Portable Device or PC With the remote playback function, you can use your portable device to playback pictures, video and music on the home network server. • The TV has obtained DLNA’s Digital Media Renderer (DMR) certification. • To use the remote playback function, you...

55 E How to connect Router ETHERNET terminal LAN n  ETHERNET cable (commercially available) 1 Switch on the router (commercially available). Refer to the router’s operation manual for switching on. 2 Connect the ETHERNET terminal on the TV to the router (commercially available) with an ETHERNET cab...

56 When using Manual setup function E Refer to “How to connect” . 2 Go to “HOME” > “TV Menu” > “Setup” > “View setting” > “Network setup” > “LAN setting” > “Manual setup” > select “Yes” > “Connection type”. 3 Press c / d to select “Wireless”, and then press ? . 4 Select “OK” ...

57 Network function Specifications (Wireless LAN) Standard IEEE 802.11a/b/g/n Frequency band 2412 f 2484 MHz 5150 f 5850 MHz Security Static WEP (64/128 bit, key index 1 only)WPA-PSK (TKIP)WPA2-PSK (AES) Modulation DBPSK@1 MbpsDQPSK@2 [email protected]/11 MbpsBPSK@6/9 MbpsQPSK@12/18 Mbps16-QAM@24 Mbps64-Q...

58 Network function Using AQUOS.NET By connecting the TV to the Internet, you can enjoy a variety of broadband content. 1 Press HOME to display the “HOME” screen. 2 Press a / b / c / d to select “AQUOS.NET” service, and then press ? . Network Setup Skype TM Home netwo AQUOS.NET Multimedia 1/7 Menu s...

59 Clear browser setting You can clear browser setting, which includes cookies, bookmarks and caches. Go to “HOME” > “TV Menu” > “Setup” > “View setting” > “Clear browser setting”. NOTE • Password input is required when executing “Clear browser setting” if Password is set. CAUTION • If y...

60 Network function DISCLAIMERS This Sharp device facilitates the access to content and services provided by third parties. The content and services accessible via this device belong to and may be proprietary to third parties. Therefore, any use of such third party content and services must be in ac...

61 Other useful features USB-recording You can enjoy DTV recording or playback by connecting a commercially available USB HDD to the TV. • USB-recording does not work for ATV, external inputs, data broadcasts, radio broadcasts or network applications. Connecting a USB HDD Connect a commercially avai...

62 Other useful features How to operate USB-recording You can enjoy DTV recording or playback by connecting a commercially available USB HDD to the TV. CAUTION • Do not unplug the AC cord or turn off the MAIN POWER switch during USB-recording timer setting or USB-recording. • When the AC cord is unp...

63 USB-recording You can record the programme you are watching to the registered USB HDD. Starting USB-recording Press REC E . • The TV starts USB-recording. NOTE • You can also operate from the control panel by pressing CONTROL . • You cannot switch the channel or the input source during USB-record...

64 Time shift playback Playback recorded scenes of the programme being recorded. Press d during recording. • Press H to return the scene that is broadcasting. NOTE • You can also operate from the control panel by pressing CONTROL . • Time shift playback may take a few moments to start.• Time shift p...

65 View setting Device format You can format all data on the USB HDD. Go to “HOME” > “TV Menu” > “Setup” > “View setting” > “USB-REC setting” > “Device format”. NOTE • Once formatting has been completed, data cannot be restored. Multimedia/Home network Multimedia/Home network In both ...

66 Photo mode Viewing thumbnails /Demo Multimedia Select photo [File name order] Flash Disk > Demo Only compatible file formats are displayed. :Back :Display photo :Select :Select/deselect slide show Image :To top menu :Slide show :Multimedia menu * This screen image is for the Multimedia mode. I...

67 Slide show E Selecting the BGM Setup the slide show BGM from “Select slide show BGM” by pressing B when selecting photo thumbnails. This function is available only for the Multimedia mode. Buttons for slide show BGM select operation Buttons Description ? When selecting a music file: Play music. a...

68 Video mode 16 Files 8 Files 15 Files 15 Files 10 Files Buttons for file selecting operations(When using Multimedia mode) Buttons Description ? When selecting a folder icon: Enter this directory.When selecting a video file: Play the video. a / b / c / d (Cursor) Select a desired item. C Return to ...

69 Other useful features EXAMPLE Item Auto Keeps the original aspect ratio in an enlarged screen display. Original Keeps the original aspect ratio and size. Full An image fully fills the screen. View setting DivX(R) setup This is the function to confirm your registration code. You need to register t...

70 Connecting a PC HDMI connection PC HDMI 1, 2, 3 or 4 terminals n  HDMI-certified cable PC HDMI 2 terminal* o p  DVI/HDMI cable  3.5 mm stereo minijack cable * When using the HDMI 2 terminal, you must select the proper item in the “Audio select” menu depending on the type of HDMI cable connecte...

71 Adjusting the PC image automatically Option Auto sync. This function enables the screen to be automatically adjusted to its best possible condition when the analogue terminals of the TV and PC are connected with a commercially available DVI/RGB conversion cable, etc. 1 Press b to select “PC” from...

72 PC control of the TV • When a programme is set, the TV can be controlled from the PC using the RS-232C or IP. The input signal (PC/video) can be selected, the volume can be adjusted and various other adjustments and settings can be made, enabling automatic programmed playing. • Use an RS-232C ser...

73 Command list CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS POWER SETTING P O W R 0 _ _ _ POWER OFF (STANDBY) INPUT SELECTION I T G D _ _ _ _ INPUT SWITCHING (TOGGLE) I T V D _ _ _ _ TV (CHANNEL FIXED) I D T V _ _ _ _ DTV (CHANNEL FIXED) I A V D * _ _ _ HDMI 1 f 4 (1 f 4), INPUT 5 f 6 (5 f 6), P...

74 You can enjoy 3D-supported images on this TV when you wear 3D glasses.To produce 3D images, liquid crystal shutters in the 3D glasses alternately open and close imperceptibly fast to exactly match alternating left and right video images displayed by the TV. NOTE • Refer to the operation manual of...

76 Enjoying 3D image viewing Using the 3D glasses Before using the 3D Glasses Before using the 3D glasses for the first time, remove the insulating sheet attached to them. Attaching the Nose Pad Attach either of the supplied nose pads as needed (such as when the glasses do not fit properly). The gla...

78 Enjoying 3D image viewing Cautions for 3D image viewing 3D glasses lenses • Do not apply pressure to the lenses of the 3D glasses. Also, do not drop or bend the 3D glasses.• Do not scratch the surface of the lenses of the 3D glasses with a pointed instrument or other object. Doing so may damage t...

79 Viewing 3D images MENU MENU NOTE • The TV screen may temporarily become black when the TV is trying to detect a 3D image signal and when switching from 3D to 2D mode. Receiving a 3D image signal that can be detected automatically The image signal may contain a 3D identification signal. You can en...

80 Enjoying 3D image viewing Watching 2D images in 3D You can convert normal 2D images into 3D images. 1 Press 3D . 2 Press c / d to select “2D s 3D”, and then press ? . 3 Turn on the power of the 3D glasses, and then wear the 3D glasses. NOTE • The confirmation message to select either 3D or 2D mod...

81 3D setup E Basic operation Go to “HOME” > “TV Menu” > “Setup” > “Option” > “3D setup” > select the menu you want to set. 3D auto change This function allows the TV to switch to 3D mode automatically when a 3D identification signal is detected. Item Mode 1 3D mode is selected automa...

82 Specifications — 3D glasses Product 3D Glasses Lens type Liquid cr ystal shutter Power supply DC3V Battery Lithium button batter y (CR2025 x 1) Battery life Approx. 100 hours of continuous use Dimension (W x H x D) 171 × 42.6 × 165.3 mm Weight Approx. 31.0 g (including the lithium battery) Operat...

83 Enjoying 3D image viewing Troubleshooting — 3D Images Problem Possible solution • 3D images are not displayed. • Is “3D auto change” set to “Off”? Press 3D to switch to 3D mode (Page 81). • If “3D auto change” is set to “Mode1” or “Mode2” but no 3D images are displayed, check the display format o...

84 Troubleshooting Problem Possible solution • No power. • Is the AC cord disconnected?• Check if you pressed < on the TV. • When the power switch does not work, remove the power plug and insert it again, and press < on the TV after waiting more than five seconds. • The TV cannot be operated. ...

85 Reset If complex adjustments are made so that the settings cannot be restored to normal, you can reset the settings to the factory preset values. 1 Go to “HOME” > “TV Menu” > “Setup” > “View setting” > “Reset”. 2 If you have already set the password, enter it here. 3 Press c / d to se...

86 Getting information Information Picture / Audio test When external equipment is connected with the TV powered on and there is no audio/video output, the TV may determine which equipment could cause a problem between the TV and the external equipment. Go to “HOME” > “TV Menu” > “Setup” > ...

87 Appendix Information on the software licence for this product Software licence You can read the software licences in this menu. Go to “HOME” > “TV Menu” > “Setup” > “Information” > “Software licence”. E Software composition The software included in this product is comprised of various...

88 Trademarks Manufactured under license from Dolby Laboratories.Dolby and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and ...

89 Specifications Item LC-90LE760X Resolution 1,920 x 1,080 Video colour system PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 TV function TV-standard Analogue PAL (B/G, D/K, I), SECAM ( B/G, D/K, K/K1), NTSC:(M) Digital DVB - T/DVB - T2 Receiving channel VHF/UHF 44.25-863.25 MHz TV tuning system Auto preset ...

90 Appendix Removing the stand • Before detaching (or attaching) the stand, make sure to turn off the TV and unplug the AC cord. CAUTION • Do not remove the stand from the TV unless using an optional wall mount bracket to mount it. Unfasten the four screws used to secure the stand in place. Detach t...

92 Appendix The wall mount kit (sold separately) allows you to mount the TV on the wall.For detailed information on installing the wall mount, see the instructions provided with the product. We recommend you to contact a technician for assistance when installing it. SHARP is not responsible for any ...

93 Dimensional drawings 1992.96 *1 2054 1243 1211 32 737 649 400 200 600 389 461 172 68 *2 116 94 445 484 1121.04 *1 *1 Active area *2 Thinnest part (except of terminal height) NOTE • Dimensions do not include protrusions such as screws and some parts. Appendix LC90LE760X_EN_book.indb 93 LC90LE760X_...

94 CLEARING THE PASSWORD 1 Go to “HOME” > “TV Menu” > “Setup” > “View setting” > “Individual setting” > “Password”. 2 The password input screen displays. 3 Press and hold both CH r and Y + on the TV simultaneously until the message appears on the screen. NOTE • To set the password aga...

Note LC90LE760X_EN_book.indb 95 LC90LE760X_EN_book.indb 95 4/4/2014 3:10:15 PM 4/4/2014 3:10:15 PM

FOR LOCATION ENQUIRIES WITHIN NEW ZEALAND REGARDING YOUR LOCAL SHARP CORPORATION OF NEW ZEALAND LIMITED VISIT OUR WEBSITE AT SHARP CUSTOMER SERVICES TELEPHONE: 09 573 0111 FACSIMILE: 09 573 0113 FOR LOCATION ENQUIRIES WITHIN AUSTRALIA REGARDING YOUR LOCAL SHARP APPROVED SERVICE CENTRE VISIT OUR WEBS...