Sharp CD-BA200 - Manuals

<P=004> (Continued) 1 2 3 ■ Removing the speaker grilles 1 Remove the lower part of the speaker grille first. 2 Remove the upper part of the speaker grille. ● Only the grills on the woofers are removable. Caution:When the speaker grilles are removed, the speaker diaphragmsare exposed. Make sur...

<P=005> (Continued) ■ Demo mode When the AC power cord is first connected, the unit will enterthe demonstration mode. To cancel the demonstration mode: When the unit is in the stand-by mode (demonstration mode),press the X-BASS/DEMO button. ● The demonstration mode will be cancelled and the un...

HK <P=001> SETTING THE CLOCK POWER ON/ STAND-BY CLOCK MEMORY/SET TUNING/TIME( ) AM 12:00 AM 0:00 0:00 2 3 4 7 6 5 8 9 In this example, the clock is set for the 12-hour (AM 12:00) sys-tem. 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Press the CLOCK button. 3 Within 5 seconds, p...

<P=002> SOUND CONTROL ■ Volume (Main unit operation) FLAT ROCK POPS JAZZ CLASSIC VOCAL 0 1 2 29 30 MAXIMUM ..... When the VOLUME control is turned clockwise, the volume willincrease. When it is turned counterclockwise, the volume willdecrease. (Remote control operation)Press the VOLUME button ...

<P=003> COMPACT DISC OPERATION ■ CD playback 1 Press the ON/STAND-BY button to turn the power on. 2 Press the CD button. 3 Press the OPEN/CLOSE button to open the disc tray. 4 Place the CD(s) on the disc tray, label side up. ● CDs can be placed on any open position on the disc tray. ● Be sure ...

<P=004> (Continued) ■ Disc number selection 1 When stopped, press the DISC SKIP button. 2 Press the 0/R ( 0R ) button. ● The next disc playback will begin, after which each followingdisc will be played sequentially. Notes: ● When t he DISC SKIP button is pressed during playback,playback will b...

HK <P=001> (Continued) ■ APMS (Automatic Programmable Music Selector) You can playback the tracks on the CDs in the disc 1 - 3 positionsin any order desired. By specifying the disc numbers from 1 to3, and the track numbers from 1 to 99, you can choose up to32 selections for playback in the ord...

<P=002> 2,3,5,6 1 4 RADIO OPERATION ■ Tuning 1 Press the ON/STAND-BY button to turn the power on. 2 Press the TUNER (BAND) button. 3 Press the TUNER (BAND) button to select the desired fre-quency band. (FM ST, FM or AM) 4 Press the TUNING/TIME ( X or W ) button to tune into the desired station...

<P=003> TAPE TAPE 1 TAPE 2 PUSH EJECT PUSH EJECT 1 2,5 6 4 3 1 6 6 3 4 2,5 (Continued) To recall a memorized station: Press the PRESET ( X or W ) button for less than 0.5 seconds to select the desired station. ● The stations (preset channel number, frequency andfrequency band) which have been ...

<P=004> RECORDING ● When recording important selections, be sure tomake a preliminary test to ensure that the desiredmaterial is being properly recorded. ● The VOLUME, X-BASS and EQUALIZER controlsmay be adjusted with no effect on the recorded sig-nal (Variable Sound Monitor). ● Metal and CrO ...

HK TIMER/ SLEEP Timer set indicator POWER ON/ STAND-BY MEMORY/SET TUNING/TIME( ) CD TUNER (BAND) TAPE (1 2) <P=001> HOW TO USE THE BUILT-IN TIMER 3 4 5 ■ Timer recording 1 Press the ON/STAND-BY button to turn the power on. ● Load a cassette for recording into the TAPE 2 cassette com-partment. ...

<P=002> USING EXTERNAL UNITS ■ Video/Auxiliary (Audio signal) input To listen to or record signals from external sourcesthrough this unit: 1 Use a separately available RCA cord to connect the desiredexternal unit to the VIDEO/AUX jacks.(red → right channel, white → left channel) ● When using v...

<P=003> MAINTENANCE ■ Internal care ● Dirty heads, capstans or pinch rollers can cause poor soundand tape jams. Clean these parts with a cotton swab mois-tened with commercial head/pinch roller cleaner or isopropylalcohol. ● After long use, the deck’s heads and capstans may becomemagnetized, c...

TINSE0276AWZZ Printed in MalaysiaB9911.HK CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agreesthat it wi...

– 5 – CD-BA200 OPERATION MANUAL RESETTING THE MICROCOMPUTER Reset the microcomputer under the following conditions: To erase all of the stored memory contents (clock and timer settings, and tuner and CD presets). If the display is not correct. If the operation is not correct. 1 Press the ON/STAND-BY...

CD-BA200 – 6 – MINI COMPONENT SYSTEM Quick Guide/Guía rápida CD-BA200 Remote control x 1 Controlador remoto x 1 2 “AA” batteries Dos pilas “AA” Remote Sensor Sensor remoto 2 Preparation for use / Preparación para su uso 1 Check the supplied accessories / Compruebe los accesorios suministrados FM/AM ...

– 7 – CD-BA200 DISASSEMBLY Caution on DisassemblyFollow the below-mentioned notes when disassemblingthe unit and reassembling it, to keep it safe and ensureexcellent performance:1. Take cassette tape and compact disc out of the unit.2. Be sure to remove the power supply plug from the wall outlet bef...

CD-BA200 – 8 – Figure 8-1 Figure 8-2 Figure 8-3 Figure 8-4 Figure 8-5 Figure 8-6 CLAMP LEVER CAM GEAR RIB (F1)x1ø3x6mm (G1)x2ø3x10mm (F1)x1ø3x10mm (F2)x3 (F2)x1 (E3)x1 (E4)x1 (E2)x2 Main PWB (E2)x1 PowerSupplyPWB PowerSupplyPWB (H1)x14ø3x10mm (H2)x1 (J1)x5ø3x10mm (K1)x1ø3x10mm (F3)x1 Display PWB Hea...

– 9 – CD-BA200 CP-BA200 1 Front Panel 1. Net .......................... (A1) x1 9-2 2. Rubber ................... (A2) x43. Screw ..................... (A3) x44. Tip .......................... (A4) x2 9-3 2 Woofer 1. Screw ..................... (B1) x4 9-3 3 Subwoofer 1. Screw .................... (...

CD-BA200 – 10 – REMOVING AND REINSTALLING THE MAIN PARTS TAPE MECHANISM SECTION Perform steps 1 to 7 and 9 of the disassembly method toremove the tape mechanism. How to remove the record/playback and eraseheads (TAPE 2) (See Fig. 10-1) 1. When you remove the screw (A1) x 2 pcs., the recording/ playb...

– 11 – CD-BA200 How to remove the pickup (See Fig. 11-2) 1. Remove the stop washer (B1) x 1 pc., to remove the gear (B2). 2. Remove the screws (B3) x 2 pcs., to remove the shaft (B4).3. Remove the pickup. Figure 11-2 CD MECHANISM SECTION Perform steps 1, 2, 3, 11 and 14 of the disassembly methodto r...

CD-BA200 – 12 – CD SECTION • AM IF/RF Signal generator: 400 Hz, 30%, AM modulated *1. Input: Antenna, Output: TP302 *2. Input: Antenna, Output: TP301 TUNER SECTION fL: Low-range frequencyfH: High-renge frequency AM IF 450 kHz 1,720 kHz T351 *1 AM Band — 530 kHz (fL): T306 *2 Coverage 1.1 ± 0.1 V AM ...

– 13 – CD-BA200 • The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chas-sis with no signal given.1. In the tuner section, ( ) indicates AM< > indicates FM stereo 2. In the main section, a tape is being played back.3. In the deck sec...

CD-BA200 – 14 – WAVEFORMS OF CD CIRCUIT T FDO TDO Stopped CH1=500mV DC 10:1 CH3=500mV DC 10:1 500ms/div (500ms/div) NORM:20kS/s 1 3 =Record Length= Smoothing : ON CH1 : 0.000VCH2 : 0.0V Main : 100KZoom : 2K Mode : AUTOType : EDGE CH1Delay : 0.0nsHold off : 0.2us CH3 : 0.000VCH4 : 0.00V BW : FULL =Tr...

CD-BA200 – 18 – Figure 18 SCHEMATIC DIAGRAM (1/10) A B C D E F G H 1 2 3 4 5 6 • NOTES ON SCHEMATIC DIAGRAM can be found on page 13. CD SIGNAL Vcc C Vref F B E A 2 5 3 1 7 6 4 4 3 2 1 7 6 5 R54 68K R53 68K R52 68K R51 68K CNP1 R56 68K R55 68K FIN2 FIN1 TIN2 TIN1 C6100/10 LDON EFBL FIN1 FIN2 REF1 TIN...

CD-BA200 – 20 – A B C D E F G H 1 2 3 4 5 6 • NOTES ON SCHEMATIC DIAGRAM can be found on page 13. Figure 20 SCHEMATIC DIAGRAM (3/10) FM SIGNAL PLAYBACK SIGNAL RECORD SIGNAL CD SIGNAL VIDEO SIGNAL CD_+B CD_GND L-CH A_GND R-CH 4 3 1 2 5 3 4 2 1 5 BI601 CNS601 AC_RLY CON VF1 VF2 -VF UN_SW 5V M_+10V +5V...

CD-BA200 – 28 – Figure 28 WIRING SIDE OF P.W.BOARD (1/8) A B C D E F G H 1 2 3 4 5 6 R608 IC601 IC301 C617 Q606 R609 C396 R391 R392 ZD351 L352 C370 C357 C358 X351 C371 C373 C374 C372 C368 R357 R370 IC303 CF351 C398 Q603 Q604 C613 Q605 C611 C607 C609 C604 C606 R616 R615 C623 C621 C627 C619 C625 C618 ...

– 37 – CD-BA200 Parts code 1. CD optical pickup Lens cleaner disc UDSKA0004AFZZ TROUBLE SHOOTING When the CD does not function When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Cleanthe objective lens, and check the playback op...

– 39 – CD-BA200 The tracking servo is not activated.Check the peripheral circuits at pins 18 and 19 on IC1, pin 23 onIC2, and CNS1A/B. If the waveform shown in Figure 39-1 appears and soon afterNO DISC appears. (2) Tracking system check Check the TE waveform at pin 18 on IC1. A normal jump operation...

– 41 – CD-BA200 FUNCTION TABLE OF IC Figure 41 BLOCK DIAGRAM OF IC IC1 VHiLA9235M/-1: Servo Amp. (LA9235M) IC2 VHiLC78641E-1: Servo/Signal Control (LC78641E) REF LA9235M REF REF REF REF REF REF REF REF AGCON ODRV AGCON ODRV REF REF LPF LPF APC ODRV REF REF REF REF LPF PH/BH PH BH 1 30 FIN1 VCC 2 29 ...

– 45 – CD-BA200 54 P120 PLAY SW_B Input PLAY SWITCH FOR T2 55 P119 FPA Input TAPE2 A-SIDE FULL PROOF 56 P118 FPB Input TAPE2 B-SIDE FULL PROOF 57 P117 MIC SW Input MIC SWITCH 58 P116 KARAOKE LATCH Output KARAOKE LATCH 59* P115 DIST_OUT/SW OUT Output DISTINATION OUTPUT/SWITCH OUTPUT 60* P112 SPN Inpu...

CD-BA200 – 46 – IC601 VHiLC75341/-1: Audio Processor (LC75341) Figure 46 BLOCK DIAGRAM OF IC 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 17 LVref RVref CONTROL CIRCUIT CONTROL CIRCUIT CONTROL CIRCUIT LOUT LBASS 0.1uF LIN LSEL0 L4 L3 L2 L1 R1 R2 R3 R4 RSEL0 R1N RTRE LTRE RBASS 0.1uF R...

– 47 – CD-BA200 FL701 VVKBJ744GNK-1: FL Display Figure 47 FL DISPLAY S1 1G (1G~8G) 2G 3G 4G 5G 6G 7G 8G S2 S3 S4 f a b k j h m g c n e r p Dp d 9G 9G 11G 14G 15G 13G 12G 10G PIN CONNECTION 58 57 56 55 54 53 52 51 50 38 49 48 47 46 45 44 43 42 41 40 39 37 36 35 34 33 32 31 20 19 18 17 16 15 14 13 12 ...

– 49 – CD-BA200 PARTS GUIDE NOTE: Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set. MODEL CD-BA200 “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and corr...

PRICE RANK DESCRIPTION NO. PARTS CODE NO. PARTS CODE PRICE RANK DESCRIPTION CD-BA200 – 1 – INTEGRATED CIRCUITS IC1 VHILA9235M/-1 J AQ Servo Amp.,LA9235M IC2 VHILC78641E-1 J AV Servo/Signal Control,LC78641E IC3 VHIM63001FP-1 J AX Focus/Tracking/Spin/Sled Driver, M63001FP IC101 VHIAN7345K/-1 J AM Play...

PRICE RANK DESCRIPTION NO. PARTS CODE NO. PARTS CODE PRICE RANK DESCRIPTION CD-BA200 C918,919 VCQYKA1HM104K J AB 0.1 µ F,50V,Mylar C920,921 VCEAZA1HW106M J AB 10 µ F,50V,Electrolytic C922,923 VCEAZA1HW107M J AC 100 µ F,50V,Electrolytic C924,925 VCKZPA1HF223Z J AA 0.022 µ F,50V C926,927 VCCSPA1HL221J...

NO. PRICE RANK DESCRIPTION PARTS CODE NO. PARTS CODE PRICE RANK DESCRIPTION CD-BA200 R582 VRD-MN2BD123J J AA 12 kohms,1/8W R583 VRD-MN2BD683J J AA 68 kohms,1/8W R584 VRD-ST2CD123J J AA 12 kohms,1/6W R585,586 VRD-MN2BD224J J AA 220 kohms,1/8W R587,588 VRD-MN2BD394J J AA 390 kohms,1/8W R589,590 VRD-MN...

PRICE RANK DESCRIPTION NO. PARTS CODE NO. PARTS CODE PRICE RANK DESCRIPTION CD-BA200 CNP11 92LCONE5P53254 J AB Plug,5Pin CNP12 92LCONEAP53254 J AD Plug,10Pin CNP101 QCNCM705CAFZZ J AA Plug,3Pin CNP102 QCNCM705GAFZZ J AB Plug,7Pin CNP301 92LCONE3P5268 J AC Plug,3Pin CNP701 QCNCWZX29AWZZ J AE Plug,29P...

NO. PRICE RANK DESCRIPTION PARTS CODE NO. PARTS CODE PRICE RANK DESCRIPTION CD-BA200 226 PRDAR0149AWFW J AP Heat Sink,Main 227 PRDAR0150AWFW J AS Heat Sink,Sub,A 228 PRDAR0151AWFW J AG Heat Sink,Sub,B ! 229 QACCD0022AWZZ J AM AC Power Supply Cord 230 QCNWN1615AWZZ J AC Lug Wire ! 231 QFSHD0001AWZZ J...

CD-BA200 A B C D E F G H 1 2 3 4 5 6 Figure 7 CD MECHANISM EXPLODED VIEW – 7 – CD-BA200 306-1 701 304 701 302 301 702 303 M1 703x4 305x2 SW4 M2 305 PWB-D 306-2 306-3 306 704

CD-BA200 A B C D E F G H 1 2 3 4 5 6 Figure 10 SPEAKER EXPLODED VIEW – 10 – CP-BA200 901,902 903,904 905,906 910 908x4 912x4 SP1,2 SP3,4 SP5,6 SP7,8 913x4 913x4 914x4 915x2 911 915x2 909x2 907 909 909 C1,2 Capacitor 3.3 µ F,100V C1,2Capacitor3.3 µ F,100V Electrolytic SP1,2 SUPER TWEETER SP3,4 TWEETE...

CD-BA200 PACKING OF THE SET (FOR U.S.A. ONLY) Setting position of switches and knobs Tape Mechanism STOP Not Replacement Item SPAKP0013AWZZ1Polyethylene Bag, Unit UNIT 92LBAG1460C1Polyethylene Bag, Accessories AM/FM Loop AntennaQuick GuideOperation ManualRemote Control SPAKC0881AWZZPacking Case FRON...