Sharp AE-Z48LZ - Manuals

5 T h e a i r p u r i f y i n g f i l t e r s a r e p a c k e d a s accessory of this unit. During operation, the fi lters remove dust and tobacco smoke from the air and discharges clean air. 1 Take out the air fi lters. 1 Open the open panel. 2 Push the air filters up slightly to unlock them. 3 Pul...

6 1 Press the COOL, DRY or HEAT button . : HEAT : COOL : DRY • The red OPERATION lamp ( ) on the unit will light. 2 To c h a n g e t h e t e m p e r a t u r e s e t t i n g , press the THERMOSTAT button. HEAT/COOL MODE • The temperature can be set within the range of 18°C to 32°C. DRY MODE • The tem...

7 HORIZONTAL AIR FLOW DIRECTION 1 Press the SWING button( ). • The horizontal airfl ow louvres will swing. 2 Press the SWING button( ) again when the horizontal airfl ow louvres are at the desired position. NOTE: • The adjusted position will be memorized and will be automatically set to the same pos...

8 SPOT AIR The louvres are adjusted so that air fl ow is delivered to the desired area. 1 Press the SPOT AIR button to select the desired air fl ow direction. NOTE: • If you want the SPOT AIR setting in the FULL P O W E R m o d e , p r e s s t h e S P O T A I R b u t t o n during the FULL POWER oper...

9 The unit works at the maximum power and op-timum louvre direction to quickly cool or warm the room. 1 D u r i n g o p e r a t i o n , p r e s s t h e F U L L POWER button. • The remote control will display “ ” and AIR FLOW symbol will get longer. • The temperature display will go off. • The green ...

10 1.2.3.5h OFF TIMER When the 1.2.3.5h OFF TIMER is set, the unit will automatically turn off after the set time (hours). 1 Press the 1.2.3.5h OFF TIMER button to set the desired time. • The time setting will change as you press the button as follows. • The orange TIMER lamp ( ) on the unit will li...

11 TIMER ON 1 Press the TIMER ON ( ) button. 2 T h e T I M E R O N i n d i c a t o r w i l l b l i n k ; press the TIME ADVANCE or REVERSE button to set the desired time. (The time can be set in 10-minute increments.) 3 Press the TIMER SET (SET/C) button. • The orange TIMER lamp ( ) on the unit will...

12 PLASMACLUSTER OPERATION Plasmacluster ions released into the room will reduce some airborne mold and viruses. 1 During operation, press the PLASMACLUSTER button. • The remote control will display “ ”. • The blue PLASMACLUSTER lamp on the unit will light up. TO CANCEL Press the PLASMACLUSTER butto...

13 ADDITIONAL NOTES ON OPERATION OPERATING TEMPERATURE RANGE VACANCY OPERATION Heating operation with 10°C set temperature will be performed to protect your home and furniture from frost damage, even when you are out. 1 Press the HEAT button. 2 Press the VACANCY button. • The remote control will dis...

14 MAINTENANCE AFTER HEAT PUMP SEASON 1 Operate the unit in the SELF CLEAN operation to allow the mechanism to thoroughly dry. 2 Stop the operation and turn off the circuit breaker. 3 Clean the fi lters, then reinstall them. MAINTENANCE BEFORE HEAT PUMP SEASON 1 Make sure that the air fi lters are n...

15 The following conditions do not denote equip-ment malfunctions UNIT DOES NOT OPERATE T h e u n i t w i l l n o t o p e r a t e i f i t i s t u r n e d o n immediately after it is turned off. The unit will not operate immediately after the mode is changed. This is to protect the unit. Wait 3 minut...