Sears KENMORE 661.62442- Manuals

Page 3 - INSTALLATION; TOOLS AND SUPPLIES YOU WILL; RULES FOR YOUR SAFETY; W ARNING; DATA; Model

INSTALLATION TOOLS AND SUPPLIES YOU WILL NEED ® Pliers® Screwdrivers ® Adjustable Wrenches ® Tubing Cutter ® 5/32 Hex Key Wrench 9 Electric Driii ® Drill Bits ® Hammer ® Duct Caulking ® 10 Sheet Metal Screws ® Wiring Supplies, as Required by Local Electrical Code ® Level RULES FOR YOUR SAFETY 1 . W ...

Page 4 - COOLER; FIGURE; ROOF KIT MOUNT; W m m Q

INSTALLATION LOCATING YOUR COOLER Your cooler has been shipped ready for installation in a down discharge position. It can easily be changed to side discharge. The cooler must be securely fastened to a frame or pad mount A roof kit is available from Sears, A duct must be attached to the cooler outl...

Page 5 - YOU RflAY WANT TO CONVERT YOUR COOLER TO SIDE DISCHARGE (Figure 3); FIGURE 3

INSTALLATION YOU RflAY WANT TO CONVERT YOUR COOLER TO SIDE DISCHARGE (Figure 3) CONVERTING COOLER TO SIDE AIR DISCHARGE (FIG.4) 0 Remove both louvers and set them where they will not fall See pg. 11^ "Taking Off Louver" (D Remove four grille clips on side opposite motor @ Remove a reservoir ...

Page 6 - LIFTING COOLER; Lift at cabinet corners

INSTALLATION LIFTING COOLER CAUTION: DO NOT LIFT ON THE LOUVERS. REMOVE THE LOUVERS BEFORE LIFTING. DO NOT LIFT ON THE CENTER OF THE CABINET FLANGES Lift at cabinet corners The cooler may be lifted by putting a bar or strap through the panel hole and lifting by means of the bar or strap ¡Fig 6) MOUN...

Page 7 - IMSTALLATION; ELECTRICAL CONNECTIONS; G s a l; SNAP COVER INIOWATEn; WAIEfl SFOU1; COMlNiESSiON; ■ fu

IMSTALLATION ELECTRICAL CONNECTIONS The wiring must comply with local codes. If you are not familiar with the codes or wiring practices, get professional help. Use only a Sears 32-6251 wall mounted switch. This new cooler does not require prewetting the pads before starting cooling and does not hav...

Page 8 - PUT FLOAT VALVE IN COOLER; TURN THE FLOAT; CONNECT WATER LINE; ADJUST WATER LEVEL; еяоммет; PUT LOUVEPS ON COOLER

IMST ä LLÄTION FINAL ASSEMBLY AND ADJUSTMENT PUT FLOAT VALVE IN COOLER Put the float valve through the spout hole and cabinet hole Tighten the ring nut. Be sure the float moves straight up and down TURN THE FLOAT UNTIL A NARROW SIDE IS UP. Snap the Splash Guard Covet into the Water Spout as shown Th...

Page 9 - NOTE: ALL DUCT CONNECTED; box; STARTUP SNSPECTION; e All louver clips are snapped tight; STARTUP CHECK LtST; Blower

INSTALLATION MOTOR PULLEY ADJUSTMENT (Figure 13) NOTE: ALL DUCT CONNECTED COOLERS MUST BE ADJUSTED Long or small afr ducts have excessive air resistance which decreases air output and motor amperage. You may compensate for this by adjusting the motor pulley. Use-a clamptype ammeter to check the moto...

Page 10 - HOW TO USE YOUR COOLER; HOW YOUR COOLER WORKS; Your cooler evaporates water to cool air.

HOW TO USE YOUR COOLER HOW YOUR COOLER WORKS Your cooler evaporates water to cool air. Evaporative air cooiing is the same natural cooling that happerts when a breeze springs up after a summer shower. You feel cool because the rain water evaporates and carries away heat- Your new cooler has a motor ...

Page 11 - CARE OF YOUR COOLER; UNPLUG YOUR COOLER BEFORE YOU WORK

CARE OF YOUR COOLER CAUTION- always UNPLUG YOUR COOLER BEFORE YOU WORK ON IT YOU COULD BE HURT IFTHE COOLER IS TURNED ON WHEN YOUR HANDS ARE INSIDE THE COOLER SPRING CARE: Clean your cooler (See page 12)Oil your cooler (See page 13)Put a new pad in if the old pad is plugged with dirt or water hardne...

Page 12 - CÄFIE OF YOUR COOLER; DISCONNECT THE ELECTRIC POWER AT

CÄFIE OF YOUR COOLER TAKING OFF PAD (Fl@. 19) 1. Lift up the $ma!! roller ends to unsnap the two center rollers. Pull out the two small rollers. 2. Pull out and turn the top roller bearing arm to line up the slot 3 . Lift edge of pad from under the guide and pull out the top roll end, 4. Take out th...

Page 13 - CARE; or YOUR; SEARS REPLACEMENT PADS; Fill the two blower shaft bearing cups @; If you can easily move the belt over 1 inch, it

CARE or YOUR COOLER PUTTING ON NiEW PAD (Pig. 21) SEARS REPLACEMENT PADS THE PADS NEED NO PREWETTING C£ Put the lower roller in pad 0 Fit the lower roller into the botton slots in the frame 0 Push the top roller through the pad Fit the roll end over the pad motor shaft drive block 0 Push the top rol...

Page 14 - REPAIR PARTS; KENMORE CONVERTIBLE DOWN/FRONT OUTLET EVAPORATIVE AIR COOLER

REPAIR PARTS KENMORE CONVERTIBLE DOWN/FRONT OUTLET EVAPORATIVE AIR COOLER MODEL I^OS, S61.823920, 861,624420, 681.624630, 861.624630, 661.624670

Page 15 - KEY; WHEN ORDERING REPAIR PARTS ALWAYS; If

REPAIR PARTS KENMORE CONVERTIBLE DOWN/FRONT OUTLET EVAPORATIVE AIR COOLER MODEL NOS. 661.623920, 661.624420 661-624S30 ,661.624630, 661.624670 NOTICE: Order by PART NUMBER, not by Key Number Refer to the back cover of this rtianuai for parts ordering information KEY PAIRT NUMBERS FOR MODEL NUMBERS r...

Page 16 - KEMMORE CONVERTIBLE DOWN/FRONT OUTLET EVAPORATIVE AIR COOLER; Model Isiumliers; The Mode! Number of your Evaporative Air Cooier wiil be; HOW TO ORDER REPAIR PARTS; AM parts listed herein may be ordered from arsy; SEARS; Distribution Center for handling

KEMMORE CONVERTIBLE DOWN/FRONT OUTLET EVAPORATIVE AIR COOLER MODEL NOS. 661.623920, 661.624420 661-624530 ,661.624630, 661.624670 Key PART NUMBERS FOR MODEL NUMBERS DESCRIPTION No. 661.623920 661.624420 661.624530 661.624630 661.624670 44 501243 501243 501243 501243 501243 Collar 45 30433 30433 3043...