Sears 536.9183- Manuals

Page 2 - TABLE OF CONTENTS; m m s m m

A Look for this symbol. It means — ATTENTION! BECOME ALERT! A HAZARDTO OPERATOR, BYSTANDERS, PROPERTYOR UNIT MAY EXIST. A TABLE OF CONTENTS Page OWNERS INFORMATION ............................................................ 2 MAINTENANCE AGREEMENT ......................................................

Page 3 - OPERATIONAL PRECAUTIONS; MAINTENANCE AND STORAGE

A OPERATIONAL PRECAUTIONS It is imperative in operating and handling your Snow Thrower that certain normal precautions be observed to prevent the possibility of injury or damage. Please read the following operational precautions before you assemble or use your new Snow Thrower. A TRAINING 1. Wear sa...

Page 4 - CONTENTS OF SHIPPING CARTON; TOOLS REQUIRED FOR ASSEMBLY; A DANGER A; HANDLE ASSEMBLY; CONTROLS ASSEMBLY; ASSEMBLY

CONTENTS OF SHIPPING CARTON 1 - 24 inch Snow Thrower (completely assembled except for handles, controls and headlight). 1 - Can of Engine Oil 1 - Upper Chute Control Rod 1 - Left Hand Handle Assembly1 - Right Hand Handle Assembly (with clutch lever attached) 1 - Control Panel Assembly 1 - Bag of Ass...

Page 6 - SKID and GAGE WHEEL; OPERATION; CAUTION; OPERATING CONTROLS; DANGER

SKID and GAGE WHEEL (Height) ADJUSTMENT OPERATION A CAUTION A For packing purposes, the gage wheels on this unit were adjusted all the way up to lowest height position. Adjust height as instructed below before using snow thrower. This unit is equipped with a pair of skids mounted on the back side of...

Page 7 - SNOW THROWER OPERATION; BEFORE STARTING ENGINE

© Chute Control Rod - Used to change direction of snow discharge. Turn handle counterclockwise to turn chute to left. Turn handle clockwise to turn chute to right. All snow can be discharged to one side by changing chute direction when changing direction of travel. • Choke Lever - Set choke lever to...

Page 8 - TO START ENGINE; ADJUSTMENTS; DRIVE BELT ADJUSTMENT

4. Change crankcase oil after the first 2 hours of operation and after each 25 hours of operation thereafter, or at the beginning of each season, whichever comes first. 5. To drain the oil, see paragraph Lubrication in Maintenance section of this manual. 6. Fill gas tank with clean, fresh, unleaded ...

Page 9 - CHUTE DEFLECTOR CABLE

3. Check belt guides (figure 12) for proper clearances as follows: IMPORTANT; Never loosen both belt guides at same time. Adjust one belt guide, retighten, then adjust other guide. A. Place impeller/auger lever in ENGAGE position. B. Have someone hold power clutch lever down to engaged position. C. ...

Page 10 - Ys; CARBURETOR ADJUSTMENT; SPARK PLUG ADJUSTMENT; MAINTENANCE; DRIVE BELT REPLACEMENT

B. Leave wheel drive control lever in position where neutral was obtained and release power cutch lever. Shut off engine. C, Loosen screws in retaining bracket (figure 15) at top end of wheel drive control rod(under control panel), D. Slide retaining bracket and rod left or right until wheel drive c...

Page 12 - ENGINE SERVICE; STORAGE; ENGINE STORAGE; UNIT STORAGE

3. The transmission has been factory lubricated for life. If, for some reason, lubricant should leak out, have transmission checked by a competent repairman. ENGINE SERVICE Unless the operator is fully qualified to make engine adjustments and repairs, it is recommended that such work be done by tech...

Page 13 - LUBRICATION CHART

LUBRICATION CHART DISCHARGE CHUTE ALL FLANGE BEARINGS A 0 ROLLER CHAIN 0" GAGE WHEEL AUGER GEAR CASE © Add Sears S.A.E. 10W oil |or equivalent) every 2 hours and after each use. © Add Sears 5W-20 oil (or equivalent) as required. Check every 5 hours and before each use. Add Sears S.A.E. SOW oil (...

Page 22 - ENGINE REPAIR PARTS; ENGINE

ENGINE REPAIR PARTS CRAFTSMAN 4-CYCLE ENGINE model number 1 43.6961 02 -22-

Page 23 - CRAFTSMAN 4-CYCLE ENGINE; Paît

CRAFTSMAN 4-CYCLE ENGINE model number i 43.696102 Ref. No. Paît No. Part Name Ref. No. Part No. Part Name 1 32586B Cylinder Assy. (Incl. Nos. 2, 3 & 41 55 30205 Bracket, Governor adjusting 2 27652 Pin, Dowel 56 30826 Spring, Extension 3 27642 Plug, Sq. hd. pipe (Oil drain) 57 30824 Link, Governo...

Page 24 - Part

CRAFTSMAN 4-CYCLE ENGINE model number 143.696102 Ref. No. Part No. Part Name Ref. No. Part No. Part Name 134 33108A Control Assy., Remote speed (incl. 154 32576 Seal, Snow guard Nos. 56 Ef 134A) 162 29918 Lockwasher, No. 8 E.T. 134A 610973 Terminai Assy. 163 32125 Cup, Starter 135 650736 Screw, Pan ...

Page 25 - Part Name

CRAFTSMAN 4-CYCLE ENGINE model number 143.696102 CARBURETOR NUMBER 631920 6 //i 10 ^ \ l Ref. No. Part No, Part Name 631920 Carburetor 1 31834 Shaft & Lever Assy., Throttle 2 632016 Spring, Throttle return 3 631036 Shutter, Throttle 4 660506 Screw, 4-40 x 3/16 5 630766 Spring, Idle regulating sc...

Page 26 - TRANSMISSION REPAIR PARTS

TRANSMISSION REPAIR PARTS 5 SPEED TRANSMISSION MODEL NUMBER 143.735 Ref. No. Part No. Part Name Ref. No. Part No. Part Name 794254 Complete Transmission 19 778113 Bevel pinion, Input 1 770061 Case, Transmission 20 786049 Sprocket (8 teeth) 2 772070 Cover, Transmission 27 780105 Bushing, Flanged 3 77...

Page 28 - Sears; owner s; SEARS; is at; YOUR; HOW TO ORDER REPAIR PARTS

Sears owner s manual MODEL NO. 536.918300 SEARS SERVICE is at YOUR SERVICE HOW TO ORDER REPAIR PARTS The Model Number will be found on a plate attached to the main frame. Always mention the Model Number when re questing service or repair parts for your CRAFTSMAN SNOW THROWER. All parts listed herei...