Sears 247.795860- Manuals

Page 2 - SAFETY RULES

SAFETY RULES A WARNING: TO REDUCE THE POTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. TRAINING • Read this owner’s manual carefully in its entirety before attempting to assemble or operate this machine. B...

Page 3 - PRODUCT SPECIFICATIONS; W AR R AN TY; ONE YEAR LIMITED WARRANTY ON CRAFTSMAN GAS CHIPPER-SHREDDER

CONGRATULATIONS on your purchase of a Sears Craftsman Chipper-Shredder. It has been designed, engi neered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest Sears Service Center/ Depa...

Page 5 - ASSEMBLY INSTRUCTIONS; TO REMOVE CHIPPER-SHREDDER FROM CARTON

ASSEMBLY INSTRUCTIONS co: Flat— Washer 5/16" I. iUQ) Hex Lock Nut 5/16-18 Thread Hex Bolt -5/16-18 X 8-3/8" Long IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see operation section of this manual for proper fuel and engine oil recommendations. NOTE: To determine ...

Page 7 - OPERATION; KNOW YOUR CHIPPER SHREDDER

To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the draw string, and pull on the drawstring until the bag is tight around the chute opening. Release plunger to lock it into position. See figure 5. OPERATION K...

Page 11 - CUSTOMER RESPONSIBILITIES; GENERAL RECOMMENDATIONS

CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS A WARNING: ALWAYS STOP THE ENGINE AND DISCONNECT THE SPARK PLUG WIRE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS. • Periodically check all fasteners and be sure they are tight. • Follow the Maintenance Schedule above. CHIPPER-SHREDDER LUBRICATIO...

Page 13 - STORAGE; ENGINE

STORAGE Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. A WARNING: NEVER STORE MACHINE WITH FUEL IN THE FUEL TANK INSIDE OF BUILDING WHERE FUMES MAY REACH AN OPEN FLAME OR SPARK, OR WHERE IGNITION SOURCES ARE PRESENT SUCH AS HOT...

Page 14 - SHARPENING OR REPLACING THE BLADES

SHARPENING OR REPLACING THE BLADES CHIPPER BLADES • Disconnect spark plug wire and move it away from spark plug. • Remove the flail screen as instructed in previous section. • Remove the chipper chute by removing three hex nuts and washers. A 1/2" wrench is required. See figure 19. NOTE: When re...

Page 16 - TROUBLE SHOOTING; HOW TO ORDER REPLACEMENT PARTS

TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION Engine fails to start • Fuel shut-off valve closed.• Fuel tank empty, or stale fuel. • Spark plug wire disconnected.• Faulty spark plug. • Open fuel shut-off valve.• Fill tank with clean, fresh fuel.• Connect wire to spark plug.• Clean, ad...

Page 17 - Repair Parts

SEARS CRAFTSMAN 8 H.P. CHIPPER-SHREDDER MODEL NOS. 247.795860 Repair Parts 247.795861 17

Page 20 - SX

BRIGGS AND STRATTON 8 H.P. ENGINE MODEL NOS. 190412-6143-01 _ ■ 190432-6117-01 Repair Parts ¿cQ, 3 * O 33 615 SX 616 614 R @ Assemblies include all parts shown in frames. R E F . N O . P A R T N O . D E S C R IP T IO N R E F . N O . P A R T N O . D E S C R IP T IO N 16 495884 Crankshaft (247.795860)...

Page 24 - LOCALIZACION DE FALLAS; COMO ORDENAR PIEZAS DE REPUESTO

LOCALIZACION DE FALLAS PROBLEMA CAUSA(S) POSIBLE ACCION CORRECTIVA El motor no se enciendet • Válvula de cierre de combustible cerrada. • El tanque de combustible está vacío, 0 combustible rancio. • El cable de la bujía está desconectado.• Bujía defectuosa. • Abra la válvula de cierre. • Llene el ta...