Scotsman NME654 - Manuals - manualsarea.com

Page 2 - INTRODUCTION; What to Do Before Calling for Service

INTRODUCTION To the owner or user: This manual is intended toprovide you with the information needed to install,start up, clean, and maintain this ice system.This is a modular ice system that fits a variety ofScotsman ice storage bins. NME454, 654 & FME504, 804 January 2007 Page 1 Table of Conte...

Page 3 - FOR THE INSTALLER

FOR THE INSTALLER These machines fit the following Scotsmanproducts, check sales literature for other possiblecombinations: · SB480 and extensions (with bin top KBT18) · HTB555 or BH550 using bin top KBT14 orKBT20 · BH801 using bin top KBT28 · BH900 using bin top KBT24 NME Dispenser Applications The...

Page 4 - SAMPLE BIN AND MACHINE COMBINATIONS

NME454, 654 & FME504, 804 January 2007 Page 3 *Bin Top Kit Required SAMPLE BIN AND MACHINE COMBINATIONS FME804 ON BH550* NME654 ON BH801* FME804 ON BH900* The Nameplate is located on the back of the machine. A Serial Number Plate is located inside the cabinet, behind the front panel.

Page 6 - FOR THE INSTALLER: Location

NME454, 654 & FME504, 804 January 2007 Page 5 FOR THE INSTALLER: Location TWO UNITS ON ONE BIN ALLOW ROOM FOR AIR CIRCULATION AND SERVICE ACCESS ALLOW AIR SPACE ON BOTH SIDES Airflow Notice: Air flow is in the sides and out the back.

Page 7 - FOR THE PLUMBER; CONFORM TO ALL APPLICABLE CODES; Water Inlet

FOR THE PLUMBER CONFORM TO ALL APPLICABLE CODES Water Inlet Air Cooled Models: Use 3 8 " O.D. copper tubing to connect cold potable water to the 3 8 " male flare fitting at the back of the cabinet. Install a handvalve near the machine to control the water supply. Water Treatment: In most are...

Page 8 - FOR THE ELECTRICIAN; CONFORM TO ALL APPLICABLE

FOR THE ELECTRICIAN CONFORM TO ALL APPLICABLE CODES Connect the electrical power to the machine to thewires in the junction box at the rear of the machine.Check the nameplate (located on the back panel)for the voltage requirements, and for the minimumcircuit ampacity. The machine requires a solidcha...

Page 9 - INITIAL START UP; Start Up

NME454, 654 & FME504, 804 January 2007 Page 8 INITIAL START UP Pre-Start Inspection 1. Remove the front and side service panels. 2. Check that any shipping blocks have beenremoved. 3. Inspect the interior of the machine for loosescrews or wires. Check that no refrigerant lines are rubbing each o...

Page 10 - CLEANING & SANITIZING

CLEANING & SANITIZING A Scotsman Ice System represents a sizable investment of time and money in any company ’s business.In order to receive the best return for that investment, it MUST receive periodic maintenance.It is the USER’S RESPONSIBILITY to see that the unit is properly maintained. It i...

Page 11 - SENSOR MAINTENANCE

1. The bin control is a device that senses light,therefore it must be kept clean so it can “see”. Atleast twice a year, remove the bin control sensorsfrom the base of the ice chute, and wipe the insideclean, as illustrated . 2. The ice machine senses water level by a probelocated in the water reserv...

Page 12 - AIR COOLED MAINTENANCE

NME454, 654 & FME504, 804 January 2007 Page 11 Clean the air cooled condenser. The air flow on this model is from front to back, sothe inside of the machine will have to be availableto clean the air cooled condenser. Use a vacuumcleaner or coil cleaner if needed. Do NOT use awire brush.A. Discon...

Page 13 - BEARING MAINTENANCE; Off

The bearing in the breaker should also be checkedat least two times per year . A. Check the bearing by: · removing the ice chute cover · unscrewing the ice sweep · removing the water shed & unscrewing thebreaker cover (left hand threads). · unscrewing the auger stud Inspect the bearing. There sh...

Page 14 - AUGER MAINTENANCE

AUGER MAINTENANCE In some areas, the water supply to the ice makerwill contain a high concentration of minerals, andthat will result in an evaporator and augerbecoming coated with these minerals, requiring amore frequent removal than twice per year. If indoubt about the condition of the evaporator a...

Page 15 - REMOVAL AND REPLACEMENT: Bin Controls

BIN CONTROLS (Ice Level Sensors) 1. Disconnect electrical power.2. Remove front panel.3. Remove control box cover.4. Locate ice chute, at the base of the chute, infront of and behind it are two plastic bin controlmounts.5. Slide each bin control to the left, and in thecontrol box, disconnect the ele...