Schweigen BR522PAK - Manuals

Page 3 - Table of Contents

Page 3 Table of Contents 1. Welcome _____________________________________________________________________________________ 2 2. Your Safety Warning _______________________________________________________________________________________ 4 Before Installation ___________________________________________...

Page 4 - Before Installation; Electrical Cord

Page 4 2. Your Safety 1. This appliance is not intended for use by person/s (including children) with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge. Unless the person has been given supervision or instruction concerning the use of the appliance by a person ...

Page 5 - Motor Features; General Notes on Installation and Use; Recommended Installation Distance

Page 5 3. General This manual is for the installation of the motor systems use for bathroom and general extraction. Motor Features • Universal mounting all position with IPX4 degree of weather protection• Patented anti water intrusion system.• Acoustic dome with super quiet, long vane, backward curv...

Page 6 - Safety of Children

Page 6 3. General Minimum Mounting Height This fan unit is intended for mounting at a minimum height of 2.1 metres (measured to the lower part of the fan impeller) above floor/ground level. Avoidance of Back Flow Care should be taken to avoid the back flow of gases into the room. Safety of Children ...

Page 7 - Three options for mounting the unit

Page 7 4. Installation Roof Mount Option Mounting Flange 110mm PVC Pipe Dektite Bell-mouth adaptor Slot option 20 min 20 min Eave Mount OptionWall Mount Option Bell-mouth adaptor Min 90mm long PVC pipe To fan Vent Electrical connection between rangehood and remote fan module Figure 1 The three optio...

Page 9 - Eaves Installation

Page 9 4. Installation 2. Eaves Installation After ensuring sufficient clearance exists for the mounting flange and ducting (figure 1), cut a circular hole 165mm Ø, maintaining adequate clearances. The eave sheeting must be reinforced. Pre-drill mounting flange recess (figure 4). If access to the ea...

Page 11 - IMPORTANT; BR522 Duel Vent System or optional DVK500 Installation

Page 11 4. Installation To main power/switch Optional Y-branch Figure 2 Ventilation Option for Dual Vent Additional dual vent kit, Y-branch, 3 metre length flexi ducting and inlet grille with adjustable damper (Kit model no: BR500 or DKV500) For dual installation, bathroom, toilet or laundry, adjust...

Page 12 - Back Draft Shutter System; Back Draft Shutter System Fitment to Bell-mouth Adaptor; IMPORANT

Page 12 5. Back Draft Shutter System Vertical Installation Figure 7 shows an example of vertical installation. Back Draft Shutter System Fitment to Bell-mouth Adaptor This back draft shutter system cannot be installed in eave type installation. Figure 6 Figure 7 Back draft shutter system Bell-mouth ...

Page 14 - Shallow Roof Space

Page 14 6. Flexible Ducting Shallow Roof Space In shallow roof spaces, 90 degree elbow PVC joint can be used as a substitute for the bend.

Page 15 - Securing Flexible Duct

Page 15 Securing Flexible Duct Flexible duct must be installed with supports at maximum intervals of 1.5 metres. Flexible ductwork can be supported by using gaffer or electrical tape, provided that it does not restrict the internal diameter of the ducting. Ducting installed looped over hanging beams...

Page 17 - Vent

Page 17 Vent 8. Measurements H old d iffuser ag a in st bo ard an d p us h up w a rd s To gg le c lip s n ap s in to p la ce ho ld in g dif fu se r fi rm ly O pe ra tion o f tog gle c lip s A B C D E F G 185 232 265 147 73 95 16 Hold diffuser aga in st bo ard and p ush upwa rds To ggle clip sn aps i...

Page 19 - Faulty Installation

Page 19 WARRANTY (See insert for more information) Motor has a 5-Year replacement product warranty. This is a change over warranty. The consumer is responsible for any charges associated with removal of the faulty unit and installation of the new unit. The customer is also responsible for any freigh...