SCAG GC-STWC-CS61V - Manuals

Page 2 - WARNING; This manual covers the operating instructions

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place.* Before performing any maintenance or service, stop the machine and remove the spark plug wire.* If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a com...

Page 3 - GRASS CATCHING OPERATION; DANGER; DIRECTION REFERENCE

1 1. With the hopper door closed, engage the deck drive. 2. Proceed to mow until the hopper is full. A replacement manual is available from yourauthorized Scag Service Dealer or by contacting:Scag Power Equipment, Service Department at P.O.Box 152, Mayville, WI 53050. You may also contactus through ...

Page 4 - LOCK

2 A . Disengage the deck drive, apply the parkingbrake and allow all moving parts to come toa complete stop. B. Pull downward on the hopper door handle toallow the hopper sweeper to remove thematerial from inside the hopper. See Figure2-1. C. Once the material has been completelyremoved from the hop...

Page 5 - Install the blower mounting bracket to the deck

3 3.1 ASSEMBLY INSTRUCTIONS FOR 61" CUTTER DECK -NOTE- Use the illustrated parts list as a part numberreference when following the assemblyinstructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assemblyparts for easy access. Prepare the work areamaking sur...

Page 6 - Ring Pins

4 12. Install the hopper mounting brackets to the outside of the frame on the rear of the machine.See Figure 3-5. FIGURE 3-5 13. With help from an assistant, install the hopper assembly to the machine by installing themounting post into the hopper mounting bracketsand secure with the ring pins. Tigh...

Page 7 - Install the hose from the blower assembly

5 14. Install the hose from the blower assembly adapter to the hopper hood and secure using the8-1/2" clamps. 15. Using the weight support bar (p/n 451517) as a guide, identify the four corresponding mountingholes, and the existing hardware that will needto be removed in order to secure the weig...

Page 8 - Re-install the side discharge chute to the opening

6 4.1 GRASS CATCHER REMOVAL INSTRUCTIONS 2005 GC-STC removal art 2-A LoosenLockingBolts RemoveMountingPins RemoveMountingPins LoosenLockingBolts 1. Prepare the machine so there is easy and safe access to the work area. Remove the key andmaintain all safety related work procedures.Always wear eye and...

Page 9 - MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS; MAINTENANCE; HOURS; GREASE FITTING

7 5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS * Perform these maintenance procedures more frequently under extreme dusty or dirty conditions. MAINTENANCE HOURS Break-In 8 20 40 100 200 500 Procedure Comments (First 10) X Check all hardware for tightness X Inspect hose and adapter X Check b...

Page 13 - Lanyard

1 1 GC-STWC-CS61V BLOWER MOUNTING COMPONENTS Ref. Part No. Number Description 1 483227 Belt Cover, GC-61V 2 04029-04 Wingnut, Plastic 3/8" Small 3 483223 Cap, Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461723 Adapter, Blower includes item #7 6 04040-14 Flatwasher, 1/4-.312 x .750 x .065 ...

Page 17 - LIMITED WARRANTY- COMMERCIAL ACCESSORY

LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer withoutcharge for parts and labor. The Sca...

Page 18 - PRINTED IN USA