SCAG GC-STT-CSV - Manuals - manualsarea.com

Page 2 - WARNING; This manual covers the operating instructions

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place.* Before performing any maintenance or service, stop the machine and remove the spark plug wire.* If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a com...

Page 3 - DIRECTION REFERENCE; DANGER; GRASS CATCHING OPERATION

1 1.1 INTRODUCTION This manual has been prepared to provide theinformation you need to correctly assemble, operate,and maintain this grass catcher. Read it carefully andkeep it for future reference. The replacement of any part on this product by otherthan the manufacturer's authorized replacement pa...

Page 5 - ASSEMBLY INSTRUCTIONS; Remove all packaging materials. Lay out the; CUTTER DECK SHOWN; Remove the right side belt cover to gain access

3 3.1 ASSEMBLY INSTRUCTIONS -NOTE- Use the illustrated parts list as a part numberreference when following the assemblyinstructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assemblyparts for easy access. Prepare the work areamaking sure that it is a clean, sa...

Page 6 - VIEW FROM RIGHT SIDE; VIEW FROM RIGHT SIDE

4 P R O P E R L Y S E R V I C E E N G I N E W I T H OILA N D F U E L . DISCHARGE CHUTE OPENING FRONT OF CUTTER DECK REAR OF CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2-52"GC-STT install art CUTTER DECK BELL CRANK LIFT LINK SPACER SPACER NUT NUT WASHER BOLT, 3/8-16 x 1-1/2" BOLT,...

Page 7 - RIGHT SIDE OF; MOUNTING PIN

5 FIGURE 3-4 8. Install the blower assembly to the mounting bracket and secure with the mounting pin andhair pin. See Figure 3-4. 9. Align the blower assembly with the discharge opening of the cutter deck. Tighten thehardware for the mounting bracket. Install thequick pin through the rear hole in th...

Page 8 - Install the hose from the blower assembly to the; Install the weight support bar to the front of the

6 13. Install the hopper mounting brackets (p/n 451512 & p/n 451595) to the outside of the frame on therear of the machine using 3/8-16 x 1" hex headbolts (p/n 04001-19) and 3/8-16 elastic stop nuts(p/n 04021-09). See Figure 3-7, Page 7. 14. Install the catcher support bracket onto the rear ...

Page 9 - Frame

7 FIGURE 3-7 Liquid Cooled Only Note: Illustration is for reference only. Some parts have been removed for visual purposes and may vary depending on model. HopperAssembly Frame Item # Part # Description 1 04001-19 Bolt, Hex Head 3/8-16 x 1" 2 04021-09 Nut, Elastic Stop 3/8-16 3 04066-03 Quick Pi...

Page 11 - MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS; MAINTENANCE; HOURS; GREASE FITTING

9 5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS * Perform these maintenance procedures more frequently under extreme dusty or dirty conditions. MAINTENANCE HOURS Break-In 8 20 40 100 200 500 Procedure Comments (First 10) X Check all hardware for tightness X Inspect hose and adapter X Check b...

Page 19 - LIMITED WARRANTY- COMMERCIAL ACCESSORY

LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer withoutcharge for parts and labor. The Sca...

Page 20 - PRINTED IN USA