SCAG GC-STC-V - Manuals - manualsarea.com

Page 2 - WARNING; This manual covers the operating instructions; REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place.* Before performing any maintenance or service, stop the machine and remove the spark plug wire.* If a mechanism becomes clogged, stop the engine before cleaning.* Keep hands, feet and clothin...

Page 3 - DIRECTION REFERENCE; DANGER

1 1.1 INTRODUCTION This manual has been prepared to provide theinformation you need to correctly assemble, operate,and maintain this grass catcher. Read it carefully andkeep it for future reference. THE REPLACEMENT OF ANY PART ON THISPRODUCT BY OTHER THAN THEMANUFACTURER'S AUTHORIZEDREPLACEMENT PART...

Page 4 - Install the blower mounting bracket to the deck

2 3.1 ASSEMBLY INSTRUCTIONS FOR 48" AND 52" CUTTER DECK -NOTE- Use the illustrated parts list as a part numberreference when following the assemblyinstructions. 1. Remove all packaging materials. Lay out the mounting hardware and the catcher assemblyparts for easy access. Prepare the work ar...

Page 6 - Install the bag assemblies.

4 17. Using the weight support bar as a guide, identifythe four corresponding mounting holes, and theexisting hardware that will need to be removed inorder to secure the weight support bar to thefront of the machine as shown. See Figure 3-9. 18. Install one 7/16-14 x 1-3/4" hex head bolt intoeac...

Page 7 - Re-install the side discharge chute to the opening; Prepare the machine so there is easy and safe

5 WARNING WARNING DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHINGKIT, OR ENTIRE GRASS CATCHER INSTALLED 7. Re-install the side discharge chute to the opening on the cutter deck. Replace the two (2) outsidemounting bolts on the discharge chute with theclevis pins (p/n 04064-15) and rue cotter pins(p...

Page 8 - MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS; MAINTENANCE; HOURS; GREASE FITTING

6 5.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS * Perform these maintenance procedures more frequently under extreme dusty or dirty conditions. MAINTENANCE HOURS Break-In 8 20 40 100 200 500 Procedure Comments (First 10) X Check all hardware for tightness X Inspect hose and adapter X Check b...

Page 9 - NOTES

Page 13 - Lanyard

1 1 GC-STC-V 48" & 52" BLOWER MOUNTING COMPONENTS Ref. Part No. Number Description 1 483224 Belt Cover, GC-STC 2 04029-04 Wingnut, Plastic 3/8" Small 3 483223 Cap, Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461723 Adapter, Blower GC-STC, includes item #7 6 04040-14 Flatwasher...

Page 16 - FRAME

1 4 GC-STC BUCKET SUPPORT COMPONENTS (LOWER) STC 2008 BSC 1 2 11 14 15 16 17 18 19 20 21 22 23 24 4 13 5 4 6 7 8 4 3 8 12 6 7 4 4 5 FRAME 9 5 10 10A TO "A" 3 6 6 9 "A" 25 26

Page 17 - Part

1 5 GC-STC BUCKET SUPPORT COMPONENTS (LOWER) 1 04090-02 Pop Rivet, 3/16 x .652 2 482321 Seal, Hood 3 423262 Tube, Upright 4 04041-07 Flatwasher, 3/8-.391 x .938 x .105 5 04021-09 Nut, Elastic Stop 3/8-16 6 04020-04 Nut, 3/8-16 7 04021-05 Hex Lock Nut, 3/8-16 8 04067-07 Pin, Ring 1/2 x 2-1/4" 9 0...

Page 19 - LIMITED WARRANTY- COMMERCIAL ACCESSORY

LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer withoutcharge for parts and labor. The Sca...

Page 20 - PRINTED IN USA