Sanyo VCB-3574IR - Manuals - manualsarea.com

Page 4 - Safety Guard; INFORMATION TO USER; For the customers in Canada

Safety Guard THIS SYMBOL INDICATES THAT THERE AREIMPORTANT OPERATING AND MAINTENANCEINSTRUCTIONS IN THE LITERATURE ACCOMPANYINGTHIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service ...

Page 5 - PRECAUTIONS

PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from theunit, or if it seems not to function correctly. Disconnect the powercord immediately, and consult your dealer (or a Sanyo AuthorizedService Centre). Do not open or modify Do not open the cabinet, as it may...

Page 6 - PARTS NAMES

PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Line phase adjustment volume (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources. Thisrolli...

Page 8 - Concerning auto-iris lenses

PARTS NAMES Concerning auto-iris lenses DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens isreferred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) VIDEO type auto-iris...

Page 9 - MOUNTING THE LENS; Checking the lens mount

MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “ L ” is more than 7 mm. If not, that may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS moun...

Page 10 - Rewiring the lens cable in the lens iris plug; Flange-back adjustment

MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. 2 Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to...

Page 11 - CONNECTIONS; Basic connection for monitoring or recording

CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Connect to 24 V AC UL listed class 2 power supply. CAUTION: • To preve...

Page 12 - SETTINGS; Electronic iris function setting; a b

SETTINGS Control name Position a Electronic iris (EI)/Backlight compensation(BLC) switch OFF b Auto-iris lens switch (A.I. LENS) DC c Lens iris level volume (LEVEL) about centre Electronic iris function setting Use a manual or fixed iris lens and set the lensaperture to the shortest F stop. Set the ...

Page 13 - Lens iris adjustment

SETTINGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR401) volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark roomand throug...

Page 14 - Line phase adjustment; TROUBLESHOOTING

SETTINGS Line phase adjustment When using a camera switcher to connect 2 cameras or more to onemonitor, there may be a vertical roll of the images when switched. Insuch a case, set as described below. Switch the display on the monitor from camera 1 to camera 2. Adjust the LINE PHASE volume on camera...

Page 15 - SPECIFICATIONS; SERVICE

SPECIFICATIONS Scanning system : EIA standard (525 TV lines, 30frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/2 inch solid state image device CCD Picture elements : 811 (H) x 508 (V) Effective picture elements : 768 (H) x 494 (V) Synchronizing system : Line lock/External sync (Automatic...