Page 3 - WARNING
− 2 − CONTENTS SAFETY PRECAUTIONS ···································································································· 2 SPECIFICATION ················································································································· 4 BEFORE USING THE REAR VIEW BACK U...
Page 4 - CAUTION
− 3 − • When installing this Rear View Back up Camera System to a vehicle equipped with air bags (The name differs depending on the manufacturer, such as SRS dual air bag, SRS side air bag, SRS curtain air bag), do not install this Rear View Back up Camera System or route its wiring where it affects...
Page 5 - SPECIFICATION
− 4 − • Route wiring properly according to the instructions. An incorrect connection might cause a fire or accident. • Be careful and prevent the wiring harness from being pinched between the vehicle body, screws, or moving parts such as the seat rails. It could cause an accident, electrocution, or ...
Page 8 - Display mode; height alignment; Offset Calibration
− 7 − REAR VIEW BACK UP CAMERA SYSTEM OUTLINE Display mode Including the standard rear view image captured by the camera, a digitally corrected rear view, view-from-top, and standard rear view can be selected. Guide lines are indicated in order to assist the driver and assure safety when backing up....
Page 9 - which some navigation systems are equipped with.
− 8 − CAUTIONS FOR CONNECTION • Before connecting, disconnect the negative battery terminal. Connect the negative battery terminal after all other connections are completed. • Connection terminals and cables are differentiated by color. Make connections to the same colors. Make sure connectors are s...
Page 10 - CONNECTION; manual provided with the unit.; Notes
− 9 − CONNECTION • Installation and wiring require technical exper tise and experience. To ensure proper installation and safety, consult the dealer where the product was purchased. CAUTION • Always use the same type of fuse with the same current rating when replacing it. • When connecting to a na...
Page 11 - Rear View Back up Camera System Installation Cautions; then install it permanently.
− 10 − BEFORE INSTALLATION Rear View Back up Camera System Installation Cautions • Bundle cables with tape or string so that they do not obstruct driving. Cables that become entangled in the steering wheel, shift selector lever or brake pedal could cause an accident. • Peel off the paper backing fro...
Page 12 - Determination of Camera Installation Position (example); Note
− 11 − Determination of Camera Installation Position (example) • Temporarily adhering the camera with the tape, locate a suitable installation position by adjusting the camera angle so that the rear of the vehicle (bumper and other areas) is visible in the monitor. • Install the camera in a position...
Page 13 - INSTALLATION; Installing system on rear spoiler; Mount the camera level with the; Position the lens axis of the camera; OK
− 12 − INSTALLATION Installing system on rear spoiler 1. Clean the location where the camera is to be installed. Wipe off oil, wax, moisture, dirt and dust using a cleaner and a clean cloth. 2. Peel off the paper backing from the tape on the camera bracket and firmly attach the bracket to a flat sur...
Page 14 - Avoid installing near the ventilators for the; There are separate surfaces for each piece
− 13 − 4. Adjust the camera angle so that the extreme rear end of the vehicle (bumper, rear window, and liftgate.) is displayed at the bottom of the monitor. • After adjusting the angle, tighten the screws with them seated at the lower end of the oblong holes in the bracket on each side. 5. Locate a...
Page 15 - How to use self-lock conductor; Do not install the control switch in a
− 14 − 7. Install the control switch in a position where it is easy to operate. Peel off the paper backing on the back of the control switch and attach it to a suitable position. How to use self-lock conductor 1. Insert the reverse signal cable of the vehicle into the self-lock conductor. 2. Fold th...
Page 16 - CABLE ROUTING; the cable as far as possible from a TV antenna, if equipped.
− 15 − CABLE ROUTING The following is an example when installing the camera on the rear spoiler. 1. Route the camera cable along the top of the liftgate and secure the cable with the cable clamps included with the Rear View Back up Camera System. Straighten the cable along the top of the spoiler (or...
Page 17 - • Connecting Video Cable
− 16 − 3. Route the camera cable to the ECU box positioned inside the vehicle and clamp it using the cable clamps. Insert the cable into the slit provided in the waterproof pad and attach the waterproof pad to the weather strip on the vehicle at the point where the cable enters the vehicle. 4. Route...
Page 18 - Preparation before performing alignment procedure
− 17 − GUIDE LINE ADJUSTMENT AFTER REAR VIEW CAMERA INSTALLATION The guide lines on the screen need to be aligned with the image taken from the rear view camera (and other reference items) so that the system is correctly matched to the vehicle. There are seven reference items to align including, (1)...
Page 19 - Alignment Mode; Alignment; turns the image off and the set parameters will NOT be stored.
− 18 − Alignment Mode Turn the ignition switch to the ACC ON position while depressing the control switch. • Press and hold the control switch until the screen appears. View-from-top alignment screen appears. (Seven rectangles at top left indicate seven items to align.) If adjustment mode cannot be ...
Page 20 - angle alignment
− 19 − 1. View-from-top angle alignment (flashing white rectangle) 1-1. Each time the control switch is pressed, the angle increases. Continuously pressing the control switch returns the alignment to the original angle. Set the parking space lines parallel to the lines on the screen. 1-2. Press and ...
Page 22 - Right guide line alignment
− 21 − 5. Right guide line alignment (flashing green rectangle) 5-1. Each time the control switch is pressed, the right guide line moves towards the center. Continuously pressing the control switch moves the guide line to its maximum right position. Set the right guide line to match the right-side m...
Page 23 - The 6 ft. guide line may not display as a
− 22 − 7. 1.5 ft. guide line alignment (flashing blue rectangle) 7-1. Each time the control switch is pressed, the 1.5 ft. guide line moves farther from the vehicle. Continuously pressing the control switch moves the line farther away until it exceeds a certain range and the line returns to the posi...
Page 24 - Preparation prior to use; corrected rear view is displayed on the screen first.
− 23 − REAR VIEW BACK UP CAMERA DISPLAY AND SWITCHING DISPLAY MODES Preparation prior to use Make sure the ignition switch is in the ON or ACC position. 1. Turn the monitor on and select the input mode switch to view the image from the rear view camera on the screen. (Refer to the instruction manual...