Samsung DW80R7060US/AA-00 - Manuals

Safety instructions English 5 SAVE THESE INSTRUCTIONS Make sure to use a new water supply line. Old lines are susceptible to breakage because they become hardened and may cause property damage due to a water leakage.The dishwasher must be connected to a hot water supply with a temperature between 12...

Installation English 6 Installation Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you are not at risk of injury when washing dishes. STEP 1 Check the parts and tools Before starting on the installation, prepare all the necessa...

Installation Installation English 8 Tools required Electric drill Safety glasses Gloves Flashlight Adjustable wrench Wire stripper Pliers Nipper Tape measure Pencil Phillips screwdriver Flat screwdriver Tubing cutter Cutting knife Hole saw Level Torx t20 Hex L-wrench DW8000R_DD68-00210A-00_EN.indd 8...

English 9 Installation NOTE New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibilit...

Installation Installation English 10 If this is a new installation, follow these steps: 1. Using a 2 1 / 2 inch hole saw, cut a hole into the side of the cabinet that holds the sink as shown in Figure 1-1 below. 2. If the base inside the sink cabinet is raised above the kitchen floor and is higher t...

Installation Installation English 12 Cabinet dimensions 24" (610 mm) minimum 34⅛-35⅓" (867-897 mm) 24" (610 mm) minimum NOTE This dishwasher is designed to be enclosed on the top and on both sides by a standard residential kitchen cabinet unit.The installation cabinet must be clean and f...

English 13 Installation STEP 3 Check water supply requirements and cautions • The hot water supply line pressure must be between 20~120 psi (140~830 kPa). • Adjust the water heater to deliver water between 120 °F (49 °C)~149 °F (65 °C). - The dishwasher must be connected to a hot water supply betwee...

Installation Installation English 14 STEP 4 Check the electrical requirements and cautions The electrical requirements for the dishwasher are as follows:• In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, install in...

English 15 Installation STEP 5 Unpacking and inspecting the dishwasher Unpack the dishwasher in an open area free of obstruction both around the packaging and overhead. We recommend that you retain all of the packing materials until the dishwasher is fully installed and operational to ensure you hav...

Installation Installation English 16 Inspecting Mechanical 1. Check the plastic base assembly to ensure that it is intact 2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can level and secure the dishwasher. 3. Check all the visible components on the bottom of th...

English 17 Installation STEP 6 Preparing the dishwasher 1. Attach the protective sticker (A) . - To prevent damage, put the protective sticker on the bottom of the counter top as shown in the picture. NOTE • Before putting the protective sticker, clean the counter top as shown in the picture.• For i...

Installation Installation English 20 STEP 7 Placing the dishwasher and connecting the hot water supply line 1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (See STEP 8 , Leveling the Dishwashe...

Installation Installation English 22 STEP 8 Leveling the dishwasher 1. Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level...

Installation Installation English 24 STEP 9 Securing the dishwasher You must secure the dishwasher to the countertop or cabinet side walls for additional stability and safety. To the countertop If the countertop is made of wood or the material will not be damaged by drilling, follow this. 1. Put a l...

English 27 Installation STEP 10 Securing 1. Check the parts on the sink to which the drain hose will be connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures. You must connect the drain hose in accordance with the w...

Installation Installation English 28 4. Slide a hose clamp over the end of the drain hose. Attach the drain hose to the sink connector, slide the hose clamp to the end of the hose, and then tighten the hose clamp. NOTE You must use a hose clamp. Failure to do so may cause water leakage. 5. To preven...

Installation Installation English 30 STEP 11 Wiring connections 1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is off. 2. In the junction box located at the front bottom right of the dishwasher, find the three power wires from the dishwasher including the groun...

Installation Installation English 32 STEP 12 Completing the installation 1. Open the door and remove all foam, paper packaging, and unnecessary parts. 2. Turn on the circuit breaker you turned off before you began the installation. 3. Open the water supply valve to supply water to the dishwasher. 4....

Speci fications English 34 Specifications Power supply 120 V, 15 A, 60 Hz AC Water pressure 20~120 psi (140 ~ 830 kPa) Dimensions (Width × Depth × Height) 23 7 / 8 x 25 x 33 7 / 8 in. (605 x 636 x 860 mm) Minimum inlet water temperature 120 °F (49 °C) NOTE Specifications are subject to change withou...

Memo DW8000R_DD68-00210A-00_EN.indd 35 4/25/2019 11:11:10 AM