Samsung AE160CXYDEK/EU - Manuals

5 English Safety Infor mation the refrigerant with other gases including air or unspecified refrigerant. Failure to do so may cause pressure increase resulting in an explosion, rupture or injury. • Do not cut or burn the refrigerant container or pipings.• Use only suitable and clean service equipmen...

6 Safety Information English Safety Infor mation Leakage detection and refrigerant recovery • The leakage detector shall be calibrated in a refrigerant-free area. • Make sure that the detector is not a potential source of ignition. • Leak detector shall be set at percentage of LFL of the refrigerant...

7 English H andling the bo x This chapter describes what needs to be done after the boxes with the outdoor and indoor units are delivered on-site. NOTE • Directly after delivery, the unit must be checked for (transport) damage. Any damage must be reported immediately to the applicable distributor of...

8 English Unit instal lation Preparing the installation of the outdoor unit Choose a sufficient space for carrying the unit to the installation location in advance.Do not choose a location where a lot of dust is created such as a construction work site. WARNING • The refrigerant inside the unit is A...

9 English Unit instal lation Safety Zone WARNING • In case of a leakage the refrigerant must not be able to enter the indoor under any circumstances. The Safety Zone shall not have any building openings such as: Windows, Doors, Light wells, Flat roof windows, Air Inlet / Outlet of ventilation system...

10 Unit installation English Unit instal lation When installing more than 1 outdoor unit (Unit : mm) 1,500 or more 1,000 or more 1,000 or more • Wall on discharge-side 300 or more 1,000 or more 1,000 or more 600 or more 300 or more • Suction-side obstacle (3 sides)• No top-side obstacle 1,000 or mor...

11 English Unit instal lation Installation guide at the seashore Make sure to follow the below guides when installing at the seashore. 1 Do not install the product in a place where it is directly exposed to sea water and sea breeze.• Make sure to install the product behind a structure (such as a bui...

12 Unit installation English Unit instal lation Moving the outdoor unit • Be sure that the moving route is safe by anticipating the weight of the outdoor unit in advance. • Do not slant the product more than 30˚when carrying it. (always keeping the unit upright) • The surface of the heat exchanger i...

13 English Unit instal lation Outdoor unit drain work General area While the air to water heat pump is operating in heating mode, ice can accumulate on the surface of the condenser.To prevent ice from growing, the system occasionally enters a defrost mode and the ice on the surface thaws off.Water d...

14 English Piping instal lation Piping installation About the piping work Water connections must be made in accordance with the Water Piping and Wiring diagram delivered with the unit, respecting the water inlet and outlet. If air, moisture or dust gets in the water circuit, problems may occur. Ther...

15 English Piping instal lation CAUTION • The operating range of leaving water temperature is 15~75˚C at heating conditions and 5~25˚C at cooling conditions. • The minimum required water flow for operation is 7 liters/ min. At all times the required water flow-rates should remain. Otherwise, the uni...

16 Piping installation English Piping instal lation Unit resistance and PHE resistance by glycol concentrate The unit is composed of water pipes and PHE basically.To ensure correct operation and predict the expected performance, Flow and Resistance table can be used and Flow and resistance character...

17 English Piping instal lation Outdoor water piping insulation The complete water circuit, inclusive all the piping, must be insulated to prevent condensation during cooling operation and reduction of the heating and cooling capacity as well as prevention of freezing of the outside water piping dur...

18 Electrical installation English El ectric al instal lation Electrical installation Electrical installation Precautions when connecting the electrical wiring WARNING • Make sure first the water piping is connected before the electrical wiring work. • When removing or relocating the equipment, powe...

19 English El ectric al instal lation Terminal block specification • 1 Phase (Unit: mm) AC power: M5 screw Communication: M4 screw N L 13 17 10.1 • 3 Phase (Unit: mm) AC power: M5 screw Communication: M4 screw N T S R 12 17 10.1 Outdoor wiring 1 Open the switch side cover. 11 13 22 1 2 3 2 Insert th...

20 Electrical installation English El ectric al instal lation To connect the power supply • Two cables must be connected to the outdoor unit – The communication cable between the indoor and outdoor unit. – The power cable between the outdoor unit and the auxiliary breaker. • Especially for the Russi...

21 English Sy st em c onfigur ation Setting the outdoor options via K-button tactile switches Setting the correct options for the outdoor unit for site specific conditions via K-button tactile switches and explanation of their functions. 7-segment display KEY (K1~K4) Setting the option 1 Press and h...

22 System configuration English Sy st em c onfigur ation Option SEG1 SEG2 SEG3 SEG4 Function of the option Base Heater 0 6 0 0 Disabled 0 1 Enabled (Factory default) Operation mode 0 7 0 0 Heat pump (Factory default) 0 1 Cooling only (Disabled) 0 2 Heating only Energy saving mode 0 8 0 0 Disabled (F...

23 English Char ging r efriger ant • Measure the quantity of the refrigerant according to the length of the liquid side pipe. Due to the small quantity of the R-290 charge, an accurate weighing of the R-290 charged in the system is mandatory to ensure proper performance. Important information: regul...

24 Troubleshooting English Troubleshooting Troubleshooting of error code Troubleshooting Troubleshooting Display Explanation Error Source E108 Setting Address Duplicate Error OUTDOOR UNIT/ Hydro Unit E120 Zone2 Indoor Room Temperature Sensor Short/Open Hydro Unit E121 Error of ROOM Temperature Senso...

25 English Technic al data Part Description CV Check Valve COMP Compressor HX_IC Heat Exchanger - Intercooler HX_M Heat Exchanger - Main (Outdoor unit) HX_PHE Heat Exchanger - PHE IPMC IPM Cooler OFM Outdoor Fan Motor AC Accumulator PS_H Pressure Sensor - High PS_L Pressure Sensor - Low PW_H1 Pressu...

27 English Technic al data P P FCU / RADIATOR HEATING UNDERFLOOR HEATING 5 ZONE 1 ZONE 2 c) OK + - OK + T P T P DHW COLD WATER CONNECTION 7 6 P TB- A Communication F1/F2 Ø 28 mm Ø 28 mm Ø 22 mm Ø 22 mm Wi-Fi 2 Ø 28 mm Ø 28 mm TB- C Power Supply a) 9 T T T 8 TB-C V1/V2 (12V Power) TB-C Communication ...

5 English Safety Infor mation the refrigerant with other gases including air or unspecified refrigerant. Failure to do so may cause pressure increase resulting in an explosion, rupture or injury. • Do not cut or burn the refrigerant container or pipings.• Use only suitable and clean service equipmen...

6 Safety Information English Safety Infor mation Leakage detection and refrigerant recovery • The leakage detector shall be calibrated in a refrigerant-free area. • Make sure that the detector is not a potential source of ignition. • Leak detector shall be set at percentage of LFL of the refrigerant...

7 English H andling the bo x This chapter describes what needs to be done after the boxes with the outdoor and indoor units are delivered on-site. NOTE • Directly after delivery, the unit must be checked for (transport) damage. Any damage must be reported immediately to the applicable distributor of...

8 English Unit instal lation Preparing the installation of the outdoor unit Choose a sufficient space for carrying the unit to the installation location in advance.Do not choose a location where a lot of dust is created such as a construction work site. WARNING • The refrigerant inside the unit is A...

9 English Unit instal lation Safety Zone WARNING • In case of a leakage the refrigerant must not be able to enter the indoor under any circumstances. The Safety Zone shall not have any building openings such as: Windows, Doors, Light wells, Flat roof windows, Air Inlet / Outlet of ventilation system...

10 Unit installation English Unit instal lation When installing more than 1 outdoor unit (Unit : mm) 1,500 or more 1,000 or more 1,000 or more • Wall on discharge-side 300 or more 1,000 or more 1,000 or more 600 or more 300 or more • Suction-side obstacle (3 sides)• No top-side obstacle 1,000 or mor...

11 English Unit instal lation Installation guide at the seashore Make sure to follow the below guides when installing at the seashore. 1 Do not install the product in a place where it is directly exposed to sea water and sea breeze.• Make sure to install the product behind a structure (such as a bui...

12 Unit installation English Unit instal lation Moving the outdoor unit • Be sure that the moving route is safe by anticipating the weight of the outdoor unit in advance. • Do not slant the product more than 30˚when carrying it. (always keeping the unit upright) • The surface of the heat exchanger i...

13 English Unit instal lation Outdoor unit drain work General area While the air to water heat pump is operating in heating mode, ice can accumulate on the surface of the condenser.To prevent ice from growing, the system occasionally enters a defrost mode and the ice on the surface thaws off.Water d...

14 English Piping instal lation Piping installation About the piping work Water connections must be made in accordance with the Water Piping and Wiring diagram delivered with the unit, respecting the water inlet and outlet. If air, moisture or dust gets in the water circuit, problems may occur. Ther...

15 English Piping instal lation CAUTION • The operating range of leaving water temperature is 15~75˚C at heating conditions and 5~25˚C at cooling conditions. • The minimum required water flow for operation is 7 liters/ min. At all times the required water flow-rates should remain. Otherwise, the uni...

16 Piping installation English Piping instal lation Unit resistance and PHE resistance by glycol concentrate The unit is composed of water pipes and PHE basically.To ensure correct operation and predict the expected performance, Flow and Resistance table can be used and Flow and resistance character...

17 English Piping instal lation Outdoor water piping insulation The complete water circuit, inclusive all the piping, must be insulated to prevent condensation during cooling operation and reduction of the heating and cooling capacity as well as prevention of freezing of the outside water piping dur...

18 Electrical installation English El ectric al instal lation Electrical installation Electrical installation Precautions when connecting the electrical wiring WARNING • Make sure first the water piping is connected before the electrical wiring work. • When removing or relocating the equipment, powe...

19 English El ectric al instal lation Terminal block specification • 1 Phase (Unit: mm) AC power: M5 screw Communication: M4 screw N L 13 17 10.1 • 3 Phase (Unit: mm) AC power: M5 screw Communication: M4 screw N T S R 12 17 10.1 Outdoor wiring 1 Open the switch side cover. 11 13 22 1 2 3 2 Insert th...

20 Electrical installation English El ectric al instal lation To connect the power supply • Two cables must be connected to the outdoor unit – The communication cable between the indoor and outdoor unit. – The power cable between the outdoor unit and the auxiliary breaker. • Especially for the Russi...

21 English Sy st em c onfigur ation Setting the outdoor options via K-button tactile switches Setting the correct options for the outdoor unit for site specific conditions via K-button tactile switches and explanation of their functions. 7-segment display KEY (K1~K4) Setting the option 1 Press and h...

22 System configuration English Sy st em c onfigur ation Option SEG1 SEG2 SEG3 SEG4 Function of the option Base Heater 0 6 0 0 Disabled 0 1 Enabled (Factory default) Operation mode 0 7 0 0 Heat pump (Factory default) 0 1 Cooling only (Disabled) 0 2 Heating only Energy saving mode 0 8 0 0 Disabled (F...

23 English Char ging r efriger ant • Measure the quantity of the refrigerant according to the length of the liquid side pipe. Due to the small quantity of the R-290 charge, an accurate weighing of the R-290 charged in the system is mandatory to ensure proper performance. Important information: regul...

24 Troubleshooting English Troubleshooting Troubleshooting of error code Troubleshooting Troubleshooting Display Explanation Error Source E108 Setting Address Duplicate Error OUTDOOR UNIT/ Hydro Unit E120 Zone2 Indoor Room Temperature Sensor Short/Open Hydro Unit E121 Error of ROOM Temperature Senso...

25 English Technic al data Part Description CV Check Valve COMP Compressor HX_IC Heat Exchanger - Intercooler HX_M Heat Exchanger - Main (Outdoor unit) HX_PHE Heat Exchanger - PHE IPMC IPM Cooler OFM Outdoor Fan Motor AC Accumulator PS_H Pressure Sensor - High PS_L Pressure Sensor - Low PW_H1 Pressu...

27 English Technic al data P P FCU / RADIATOR HEATING UNDERFLOOR HEATING 5 ZONE 1 ZONE 2 c) OK + - OK + T P T P DHW COLD WATER CONNECTION 7 6 P TB- A Communication F1/F2 Ø 28 mm Ø 28 mm Ø 22 mm Ø 22 mm Wi-Fi 2 Ø 28 mm Ø 28 mm TB- C Power Supply a) 9 T T T 8 TB-C V1/V2 (12V Power) TB-C Communication ...