Samsung AE071ANMPEH/EU - Manuals

5 English Safety Inf ormation CAUTION Install your appliance on a level and hard floor that can support its weight. • Failing to do so may result in abnormal vibrations, noise, or problems with the product. Install the draining hose properly so that water is drained correctly. • Failing to do so may...

6 English Safety Information Safety Inf ormation FOR USING WARNING If the appliance is flooded, please contact your nearest service centre. • Failing to do so may result in electric shock or fire. If the appliance generates a strange noise, a burning smell or smoke, unplug the power plug immediately...

7 English Safety Inf ormation After unpacking the air conditioner, keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children. • If a child places a bag over its head, it may result in suffocation. Do not touch the front panel with your hands ...

8 English Safety Information Safety Inf ormation CAUTION Do not place objects or devices under the indoor unit. • Water dripping from the indoor unit may result in fire or property damage. Check that the installation frame of the outdoor unit is not broken at least once a year. • Failing to do so ma...

9 English Safety Inf ormation This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsi...

10 English A t a Glanc e Indoor Unit Overview At a Glance Congratulations on the purchase of the air conditioner. We hope you enjoy the features of your air conditioner and stay cool or warm with optimal efficiency. Please read the user manual to get started and to make the best use of the air condi...

11 English Cleaning and Maint enanc e Cleaning the Air Conditioner Cleaning and Maintenance Cleaning the air filter For the best performance from your air conditioner, clean it periodically. When cleaning, make sure to unplug from the unit for user’s safety.When cleaning the filter, make sure to unp...

15 English Cleaning and Maint enanc e Maintaining the Air Conditioner If the air conditioner will not be used for an extended period of time, dry the air conditioner to maintain in best conditions. 1. Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect the pow...

17 English Appendix Refer to the following chart if the air conditioner operates abnormally. This may save time and unnecessary expense. Problem Solution The air conditioner does not operate at all. • Check if the power plug is properly connected.• Check whether the auxiliary power switch (MCCB, ELB...

21 English Appendix Operating temperature and humidity Mode Outdoor temperature Indoor temperature Indoor humidity Cool mode -5°C to 48°C 18°C to 32°C 80% or less Heat mode -20°C to 24°C 27°C or less - Dry mode -5°C to 48°C 18°C to 32°C - NOTE • The standardized temperature for heating is 7˚C. If th...

22 English Appendix Type Model Net weight (kg) Net dimension (W x D x H) (mm) Indoor unit AE022ANLDEH/EU 15.3 700 x 440 x 199 AE028ANLDEH/EU 15.3 700 x 440 x 199 AE036ANLDEH/EU 15.7 700 x 440 x 199 AE056ANLDEH/EU 18.9 900 x 440 x 199 AE071ANMPEH/EU 27.9 850 x 700 x 250 AE090ANMPEH/EU 35.4 1200 x 700...

ENGLISH-5 01 PREPAR ATION f f Servicing shall be performed following the controlled procedure to minimize the risk of flammable refrigerant or gases . f f Do not install where there is a risk of combustible gas leakage . f f Do not place heat sources . f f Be cautious not to generate a spark as foll...

ENGLISH-6 Safety precautions Leakage detection methods f f The leakage detector shall be calibrated in a refrigerant-free area . f f Make sure that the detector is not a potential source of ignition . f f The leakage detector shall be set to the LFL (lower flammability limit) . f f The use of deterg...

ENGLISH-7 01 PREPAR ATION Installation location requirements f f The unit shall be installed in an open space that is always ventilated . f f The local gas regulations shall be observed . f f For installation inside a building (this applies either to indoor or outdoor units installed inside) a minim...

ENGLISH-8 Product specifications Product compatibility Line-up Heat pump units Chassis Model Name Split AE040RXED** AE060RXED** AE090RXED** - Mono AE050RXYD** AE080RXYD** AE120RXYD** AE160RXYD** Indoor units Tank Integrated Hydro Units Model Name Split AE200RNWSEG AE260RNWSEG AE200RNWSEG AE260RNWSEG...

ENGLISH-9 01 PREPAR ATION Accessories Installation Manual (2) Zone sensor (1x10m, WH) (2) Temperature Sensor for Mixing Valve (1x15m, BLU) (1) Sensor holder of zone sensor and mixing valve (3) Sensor clip of zone sensor and mixing valve (3) Cable-tie for zone sensor and mixing valve (6) Aluminum tap...

ENGLISH-10 Product specifications Specifications Model Name AE200RNWSEG AE260RNWSEG AE260RNWSGG AE200RNWMEG AE260RNWMEG AE260RNWMGG Type Split Mono Power source V/Hz 1Φ, 220-240V~, 50Hz 1Φ, 220-240V~, 50Hz 1Φ, 220-240V~, 50Hz 3Φ, 380-415V~, 50Hz 1Φ, 220-240V~, 50Hz 1Φ, 220-240V~, 50Hz 1Φ, 220-240V~,...

ENGLISH-11 01 PREPAR ATION Typical application examples • The application examples given below are for illustration purposes only .• When the SAMSUNG Air-to-Water Heat Pump system is used in series with another heat source (e .g . gas boiler), ensure that the return water temperature not exceed 65 °...

ENGLISH-13 01 PREPAR ATION Main components ❋ ❋ Split ① ② ③ ④ ⑤ ⑥ ⑦⑨⑩ ⑪ ㉑ ⑮ ㉓ ㉕ ㉖ ⑧ ⑲ ⑱ ⑳ ⑰ ⑯ ⑭㉒ ㉔ ㉗ ㉘ ㉙ ㉚ ㉛㉜㉝ ⑬ ⑫ No. Part name Note ① Refrigerant pipe ø15 .88 (5/8"), Flare nut ② Refrigerant pipe ø6 .35 (1/4"), Flare nut ③ Hot water outlet ø22, Straight pipe ④ Secondary return ø22, Straight...

ENGLISH-17 01 PREPAR ATION Functional diagram ❋ ❋ Split 3 G3 KIT 3-Way V/V Backup heater(2kW) PWM Pump HX_PHE Expansion Vessel(8L) Flow sensor Pressure Relief v/v Air Vent Manometer Water in Water out Temperature & pressure relief valve Drain(Tundish) T_tank T_w3 T_w2 T_w1 Heating T_eva out T_ev...

ENGLISH-18 Dimensional drawing ①② ③ ④ ⑤⑥⑦ 595 700 85 85 85 85 70 70 1844 42 No Split Size type ① Refrigertant (Gas) Ø15 .88 Flare nut ② Refrigertant (Liquid) Ø6 .35 Flare nut ③ Hot water outlet Ø22, T1 .0 Straight pipe ④ Secondary return (260L option) Ø22, T1 .0 Straight pipe ⑤ Cold water inlet Ø22,...

ENGLISH-19 02 INSTALLATION Installing the unit Installation of the indoor unit The indoor unit should be installed indoors and meet the following conditions . f f Installation site should be sheltered from frost . f f In area with suitable space for servicing . f f A place with adequate ventilation ...

ENGLISH-20 Installing the unit Moving the Indoor unit f f Select the moving route in advance . f f Be sure that moving route is safe from weight of the indoor unit . Moving the Indoor unit with a fork lift f f Insert the fork into the wooden pallet at the bottom of the indoor unit carefully . Be car...

ENGLISH-21 02 INSTALLATION Base construction and installation of the Tank hydro unit Manufacturer is not responsible for the damage occurred by not following the installation standards .1 . Considering the vibration and weight of the Tank hydro unit, strength of the base ground must be strong enough...

ENGLISH-22 Pipe work Refrigerant pipe work For all guide lines, specifications regarding refrigerant pipe work between the indoor unit and the outdoor unit, please follow the outdoor unit installation manual . Gas pipe (O .D .) Liquid pipe (O .D .) Indoor unit 15 .88 mm (5/8 inch) 6 .35 mm (1/4 inch...

ENGLISH-23 02 INSTALLATION Water pipe work The hydro unit is equipped with components listed on the table below .The hot and cold water supply connections are clearly marked on the unit with labels . And service valves are provided .Whole water plumbing system including Hydro unit shall be installed...

ENGLISH-24 Pipe work Flushing and air-purging When filling water, the following start-up procedure should be followed . 1 . All system components and pipes must be tested for the presence of leaks .2 . Make-up water assembly or Flushing unit is recommended for installation and service .3 . Before co...

ENGLISH-26 Pipe work PWM characteristic curve PWM input signal(%) Max . Speed The additional pump should be the same type of product as the above graph .RecommendationGRUNDFOS UPMM 25-95 (Heating Type) Case 2) AC pump The maximum number of additional pump installation is one AC pumps (Input power 10...

ENGLISH-27 02 INSTALLATION Setting the pre-pressure of the expansion vessel When it is required to change the default pre-pressure of the expansion vessel(1 bar), keep in mind the following guidelines: f f Use only dry nitrogen to set the expansion vessel pre-pressure . f f Inappropriate setting of ...

ENGLISH-28 Pipe work Charging water Liquid Pipe Gas Pipe Cap Water Inlet Air-vent valve Water Outlet DHW Inlet Recirculation Inlet (Only 260 Liter Model) DHW Outlet After installation is completed the following procedures shall be used to charge water into the hydro unit . f f Connect water lines to...

ENGLISH-29 02 INSTALLATION Wiring work • Field-supplied electrical components such as power switch, circuit breakers, wires, terminal blocks, etc must be properly chosen with compliance with national legislation or regulation . • Switch off the power supply before making any connections .• All field...

ENGLISH-36 Wiring work Selecting solderless ring terminal f f Select a solderless ring terminal of a connecting power cable based on a nominal dimensions for cable . f f Cover a solderless ring terminal and a connector part of the power cable and then connect it . Nominal dimensions for cable (mm 2 ...

ENGLISH-37 02 INSTALLATION Torque requirements CONTROL-KIT PBA M3 M3 M3.5 M3.5 M4 Screw size Tightening torque (N·m) Part Terminal code Remarks M3 0 .5~0 .75 Control Kit PBA 2P Terminal Block PV/Peak power control SIGNAL Dry contact input R-32 ALARM Dry contact output WATER PUMP PWM signal output M3...

ENGLISH-39 02 INSTALLATION Types of allowable current Conductors of supply cord shall have a nominal cross-sectional area not less than that shown in the table below . Minimum cross-sectional area of conductors Rated current of appliance (A) Nominal cross-sectional area (mm2) ≤0 .2 Tinsel cord a) ≤0...

ENGLISH-40 Wiring work Checking correct grounding If the power distribution circuit does not have a grounding or the grounding does not comply with specifications, an grounding electrode must be installed . The corresponding accessories are not supplied with the Air to Water Heat pump .1 . Select an...

ENGLISH-43 02 INSTALLATION Connecting the power terminal f f Connect the cables to the terminal board using the solderless ring terminal . f f Use certified and reliable cables . f f Connect the cables with the torque chart as below . f f If the terminal is loose, fire may occur caused by arc . If t...

ENGLISH-44 Wiring work 1 phase 3 phase Booster heater (DHW, assembly in factory) 1 Phase ELCB 1 Phase ELCB 3 Phase ELCB DHW Tank Connection of the thermostat Description No. of wires Max. current Thickness Supply Scope Room Thermostat 4 22mA > 0 .75 mm 2 , H05RN-F or H07RH-F Field supply (220-240...

ENGLISH-47 02 INSTALLATION Connection of the 3-way valve Description No. of wires Mini. / Max. current Thickness Supply Scope Diverting type 3way valve 4 10mA / 50mA > 0 .75 mm 2 , H05RN-F or H07RN-F Field supply (220-240V~, Input) B17 : 3WAY (L1) B18 : 3WAY (L2) B16 : Live (L) B15 : Neutral (N) ...

ENGLISH-48 Wiring work Connection of the back-up boiler Description No. of wires Mini. / Max. current Thickness Supply Scope Back-up Boiler 2+ground 10mA / 50mA 0 .75mm 2 H05RN-F or H07RN-F Field supply (220-240V~, Input) L N L N When it set back up boiler on the hydro unit (relay off ) Boiler B4 : ...

ENGLISH-49 02 INSTALLATION Connecting for smart grid ready control 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Connection terminal for SG READY Signal 1 Connection terminal for SG READY Signal 2 SG READY Signal 2 SG READY Signal 1 SG READY Signal 1 SG READY Signal 2 Product operation Short Op...

ENGLISH-50 Self-test mode of wired remote controller Use of self-test mode 0 Please enter your PASSWORD Service mode Service mode Reset All Service Mode Power Master Reset ODU K3 Reset Field Setting Value Self-Test Mode Indoor Unit Option 1 . If you want to use the various additional functions for y...

ENGLISH-51 03 O THERS Troubleshooting If the unit has some problem to work properly, the LED on hydro unit will flash and some error codes will be displayed on the controller .The following table described the explanation of error codes on the LCD display . Thermistor f f Check its resistance . 10ko...

ENGLISH-52 Troubleshooting Communication Display Explanation Communication error between remote controller and the Hydro unit Tracking error between remote controller and the Hydro unit Memory(EEPROM) Read/Write Error(Wired remote controller data error) E601, E604 E654 MEMORY(EEPROM) Read/Write Erro...

ENGLISH-53 03 INSTALLATION Water pump & Flow Sensor Display Explanation Low flow rate error• in case of low flow rate in 30 sec during water pump signals is ON(Starting)• in case of low flow rate in 15 sec during water pump signals is ON(After starting)Normal flow rate error• in case of normal f...

ENGLISH-54 DHW tank Piping diagram • The product must be installed without any water leakage .• Please verify that the DHW tank and other components are properly installed and reinstall them if necessary . - Use certified components and the correct tools . - Keep adequate space for the installing . ...

ENGLISH-55 03 INSTALLATION No. Note No. Note ① Service valve ⑦ T-Joint ② 3 way diverting valve ⑧ Expansion relief Valve ③ Drain Valve ⑨ T-Joint ④ T-Joint ⑩ Pressure reducing valve with integrated check valve and strainer ⑤ Tundish Tank Temp Temperature sensor for DHW tank ⑥ Expansion vessel ❋ ❋ The ...

ENGLISH-56 DHW tank Switch box layout DHW Tank Temp . CNS042(YEL) • When you set the hot water supply temperature to 55°C or less, do not use the booster heater . - The heatpump and the booster heater operate until the initial set temperature is reached . After that, only the booster heater may oper...

ENGLISH-57 03 INSTALLATION Electrical connections Procedure • Switch off the power supply before making any connections .• Use a thermal grease in thermistor pocket after installing electric connections . WARNING Connections to be made in the electrical box of DHW tank 1 . Connect the booster heater...

ENGLISH-59 03 INSTALLATION Mixing Valve Installation of mixing valve Under Floor Radiator TW4 Balancing Vessel (Mixing tank) When two different zones are used with different temperature, adjust the temperature of discharge water to high temperature water and control the amount of bypass to provide l...

ENGLISH-60 Mixing Valve ❋ ❋ The mixing valve is controlled based on the FCU WL value . ❋ ❋ As the #4044 value increases and the #4045 value decreases, the control speed increases . (Temperature hunting may occur if the control speed increases depending on the load .) ❋ ❋ The additional pump and mixi...

ENGLISH-61 03 INSTALLATION 2-Zone Control Using Remote Controller 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Tw2_z2 M Tw2_z1 Zone2 19/20 17/18 B14/B15 B10/B11 B2/B3/B5 Radiator Zone1 Under Floor Balancing Vessel Mixing Senser(Default, 15 m) CNS045(BLU) You can operate the 2-zone control usin...

ENGLISH-62 Temperature sensor work Example of sensor installation Weld the sensor holder on the selected location of the pipe and then insulate it . When the pipe is a copper pipe When the pipe is not a copper pipe Pipe Sensor holder Pipe Sensor Sensor clip Sensor Aluminum tape Sensor Rubber tape Se...

ENGLISH-63 03 INSTALLATION Setting the EHS converter Mode Selection switch Micro SD card Left position: Field Setting Value (FSV) mode Right position: Operating Data Backup mode Left position Right position f f Micro SD card is a separate purchase, using 8 ~ 32GB It's possible .

ENGLISH-64 Temperature sensor work Reading and writing FSV How to upload or download field settings (example) 1 . Insert an SD card into the Sub PBA SD Card slot on the Hydro unit . Micro SD card 2 . Select Field Setting Value in Service mode .3 . Press Up/Down button to select FSV Upload or Downloa...

ENGLISH-65 03 INSTALLATION How to download to a microSD card 1 . Download the wired remote controller image, change the file name to “IMAGE .BIN,” and then download to microSD Card .2 . Download the wired remote controller program, change the file name to “MICOM .BIN,” and then download to microSD C...

ENGLISH-66 Temperature sensor work When the microSD Card is removed during download 1 . When you remove the microSD Card during download, the “INSERT MICROSD CARD AND SYSTEM RESET” screen appears and the download is stopped . 2 . When you insert the microSD Card and press the and buttons for system ...

ENGLISH-67 03 INSTALLATION Concrete curing function When pipes of floor heating are installed, operation for reinforcing concrete curing is applied . (Period of operation: 23 days) Entering procedure 1 . After turning off the DIP switch K3 of indoor unit (Default ON), power off and on the indoor uni...

ENGLISH-68 Concrete curing function NOTE • Definition of Dip switch function Dip S/W S/W #1 S/W #2 S/W #3 S/W #4 ON (default) • None • None • None • Turn off when an E101 error occurs OFF • Emergency heating • Emergency hot water supply • Concrete curing • E101 error does not turn off reference item...

ENGLISH-69 03 INSTALLATION Installation option setting f f Set the indoor unit installation option with remote controller option . The procedure of option setting High Temp Button High Fan Button Mode change Low Temp Button Low Fan Button Entering mode for option setting Option setting mode Entering...

ENGLISH-70 Installation option setting Changing a particular option You can change each digit of set option . Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 Explanation PAGE MODE The option mode you want to change The tens’ digit of an option SEG you will change The unit digit of an option SEG you will change...

ENGLISH-71 03 INSTALLATION Optional : Extending the power cable 1 . Prepare the following tools . Tools Spec Shape Crimping pliers MH-14 Connection sleeve (mm) 20xØ6 .5 (HxOD) Insulation tape Width 19 mm Contraction tube (mm) 70xØ8 .0 (LxOD) 2 . As shown in the figure, peel off the shields from the ...