Ryobi ZRRY41002- Manuals

Page 6 The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous...

Page 7 MOTOR Motor Type ......................................................................................................................................................... 120 V ACOperating RPM........................................................................................................

Page 8 Fig. 1 TOP-MOUNTED MOTOR The top-mounted motor improves balance and is lo-cated away from the dust and debris of the cutting area. CORD RETAINER The cord retainer helps prevent accidental unplugging of the extension cord. DUAL LINE The dual line permits more efficient and aggressive cutting. ...

Page 9 Fig. 3 Fig. 2 CONNECTING THE ATTACHMENT TO THE UPPER SHAFT See Figure 2. The coupler connects the attachment to the upper shaft. Follow these steps to connect the attachment to the up-per shaft. n Loosen the knob by turning it counterclockwise. n Remove the end cap from the attachment shaft. ...

Page 10 Fig. 4 ATTACHING THE GRASS DEFLECTOR See Figure 4. WARNING: The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury. Follow these steps to attach the grass deflector. n Slide the grass deflector onto...

Page 11 WARNING: The product may throw objects during operation, caus-ing injury to the operator or to bystanders. Always wear suitable eye protection, boots, gloves, and long, heavy pants while operating the product. STARTING AND STOPPING THE TRIMMER See Figure 7. n To start the trimmer: Press the ...

Page 12 Fig. 9 Fig. 10 RETAINING CAP RETAINING CAP LINE n The tip of the cutting line will wear during use; this reduces the cutting swath. If the line is not advanced occasionally, it will wear down to the eyelet. When the trimmer stops, the line tends to relax and may retract into the trimmer head...

Page 13 CUT OFF BLADE This trimmer is equipped with a cut-off blade on the grass deflector. For best cutting, advance string until it is trimmed to length by the cut-off blade. Advance string whenever you hear the engine running faster than normal. This will maintain best performance and keep string...

Page 14 WARNING: Use only identical Ryobi replacement parts when ser-vicing this product. Use of any other parts may create a hazard or cause product damage. CLEANING THE TRIMMER Release the trigger, allow the trimmer to coast to a stop, and unplug the trimmer before cleaning. n Clean the exterior o...

Page 15 n Wind the line counterclockwise around the spool fol-lowing arrows on spool. Do not overfill. NOTE: After winding the line, there should be about 6 in. (152 mm) between the wound line and the outside edge of the spool. n Secure the line temporarily by pushing it into one of the slotted tabs...

Page 16 1. Lubricate with a silicone spray.2. Install more line (Refer to “Replacing the Cut- ting Line” earlier in this manual). 3. Pull lines while alternately pressing down on and releasing spool retainer. 4. Remove line from spool and rewind (Refer to “Replacing the Cutting Line” earlier in this...

Page 17 WARNING: The use of attachments or accessories not listed above could result in serious personal injury. REPLACEMENT PARTS String Head (RH Thread) .080 in. (2 mm) ......................................................................................................... DA03001ASpool & Lin...

Page 18 WARRANTY LIMITED WARRANTY STATEMENT Ryobi Technologies, Inc. warrants to the original retail purchaser that this Ryobi Technologies, Inc. product is free from defect in material and workmanship and agrees to repair or replace, at Ryobi Technologies, Inc.’s discretion, any defective product f...

• SERVICE Now that you have purchased your product, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Authorized Service Center. • MOD...