Ryobi YN200BN- Manuals

6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts. WARNING: To avoid ...

7 GLOSSARY OF TERMS Activate (operating controls) To move an operating control so that it is in a position that allows the tool to be actuated or that satisfies one requirement for the tool to be actuated. Actuate (tool) To cause movement of the tool component(s) intended to drive a fastener. Air in...

8 FEATURES Fig. 1 PRODUCT SPECIFICATIONS Operating Pressure............................................. 70-10 psiFastener Type ...................................... 18 gauge brad nailsFastener Range ............................................. 5/8 in. to in.Magazine Capacity ........................

10 DANGER: Do not use oxygen, combustible gases or bottled gases as a power source for this tool. The tool will explode and cause death or serious injury. WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe ...

11 OPERATION WARNING: Always wear eye protection. Eye protection does not fit all operators in the same way. Make sure the eye protection chosen has side shields or provides protection from flying debris both from the front and sides. PREPARING THE TOOL FOR USE See Figure 2. Under normal use conditi...

1 OPERATION WARNING: Disconnect the tool from the air supply before leaving the work area, moving the tool to another location, or handing the tool to another person. Failure to do so could result in serious personal injury. CONNECTING THE TOOL TO AN AIR SUPPLY See Figure 5. DANGER: Do not use oxyge...

13 OPERATION LOADING THE TOOL WITH NAILS See Figures 6 - 7.  Connect the tool to the air supply. WARNING: The tool’s driving mechanism may cycle when the tool is first connected to the air supply. Always connect the tool to the air supply before loading nails to prevent injury from unintended cycli...

14 OPERATION Fig. 8 TRIggER woRKPIECE ConTaCT DRIVING A FASTENER See Figure 8. WARNING: Never wedge or hold back the workpiece contact mechanism during operation of the tool. Doing so could result in possible serious injury. SINGLE SEQUENTIAL ACTUATION Single sequential actuation provides accurate f...

15 SETTING THE AIR PRESSURE The amount of air pressure required will depend on the size of the nail and the workpiece material. Begin testing the depth of drive by driving a test nail into the same type of workpiece material used for the actual job. Drive a test nail with the air pressure set at 90-...

16 OPERATION CLEARING A JAMMED FASTENER See Figure 11. WARNING: Disconnect the tool from the air supply before clearing a jammed fastener. Failure to do so could result in serious personal injury. If a nail or fastener becomes jammed in the tool, disconnect the air hose and keep the tool pointed awa...

17 MAINTENANCE LUBRICATION Frequent, but not excessive, lubrication is required for best performance. Oil for pneumatic fastening tools added through the air line connection will lubricate the internal parts. Do not use detergent oil or additives as these lubricants will cause accelerated wear to t...

18 MAINTENANCE REQUIRED DAILY CHECKLIST  Disconnect the air supply from the tool and remove all fasteners.  Check all screws, nuts, bolts, and pins on the tool. If any of these are loose, they must be tightened with the appropriate size wrench.  Press the workpiece contact against a workpiece to ...

TROUBLESHOOTING Air leak near the top of the tool or in the trigger area PROBLEM POSSIBLE CAUSE SOLUTION Loose screwsWorn or damaged O-rings or seals Tool does nothing or operates sluggishly Tool jams frequently Tighten screwsInstall Overhaul Kit Inadequate air supplyInadequate lubricationWorn or da...

0 YN00BN 987000-1067-5-07 (REV:00) • PARTS AND SERVICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate. • MODEL NUMBER • SERIAL NUMBER • HOW TO OBTAIN REPLACEMENT PARTS: Replacement parts can be purchased online at w...