Ryobi TR45- Manuals

Page 2 - RYOBI; WHAT THIS WARRANTY COVERS:; ADDITIONAL LIMITATIONS:

Page 2 Page 3 n Introduction ..................................................................................................................................................................... 2 � n Warranty .............................................................................................

Page 3 - GENERAL SAFETY RULES; SAVE THESE INSTRUCTIONS

Page 2 Page 3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS WORK AREA n Keep your work area clean and well lit. Cluttered benches and dark...

Page 4 - SERVICE; Save these instructions.

Page 4 Page 5 SERVICE n Tool service must be performed only by qualifiedrepair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. n When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this ma...

Page 5 - SYMBOLS; SYMBOL

Page 4 Page 5 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols will allow you to operate the tool better and safer. Read The Operator’s Manual Safety Alert No Hands Symbol No Hands Symbol No Hands Symbo...

Page 6 - AUTHORIZED SERVICE CENTER

Page 6 Page 7 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical replacement parts. WARN...

Page 7 - DOUBLE INSULATION; ELECTRICAL CONNECTION; power supply that is 120 volts, 60 Hz, AC; EXTENSION CORDS; WARNING; ELECTRICAL

Page 6 Page 7 DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools d...

Page 8 - FEATURES; PRODUCT SPECIFICATIONS

Page 8 Page 9 FEATURES Fig. 1 PRODUCT SPECIFICATIONS Maximum Cutter Diameter . . . . . . . . . . .1-1/8 in. (29 mm)Collet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 in. (6.35 mm)No Load Speed . . . . . . . . . . . . . . . . . . . . . . . . 25,000/min. Input . . . . . . . . . . . . ....

Page 10 - ASSEMBLY; INSTALLING/REMOVING CUTTERS

Page 10 Page 11 ASSEMBLY Fig. 2 INSTALLING/REMOVING CUTTERS See Figure 2. n Unplug the trimmer. n Place the trimmer upside down on a workbench to gain easy access to the spindle and collet nut. n Place the small end of one of the wrenches provided on the spindle flats. This will hold the spindle sta...

Page 11 - OPERATION; APPLICATIONS; OFF; HOW TO OPERATE THE TRIMMER; ON

Page 10 Page 11 OPERATION WARNING : Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is suf-ficient to inflict serious injury. WARNING : Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so ...

Page 12 - DIRECTION OF FEED AND THRUST; TRIMMER FEED

Page 12 Page 13 OPERATION DIRECTION OF FEED AND THRUST See Figures 6 and 7. The trimmer motor and cutter revolve in a clockwise direc-tion. This gives the tool a slight tendency to twist in your hands in a counterclockwise direction, especially when the motor starts.Feed the trimmer into the workpie...

Page 13 - PROPER RATE OF FEED; FORCE FEEDING; TOO SLOW; TOO SLOW FEEDING

Page 12 Page 13 OPERATION speed and is taking very small bites to produce tiny, cleanly-severed chips. If the trimmer is forced to move forward too fast, the speed of the cutter becomes slower than normal in relation to its forward movement. As a result, the cutter must take bigger bites as it revol...

Page 14 - DEPTH OF CUT

Page 14 Page 15 OPERATION Fig. 9 DEPTH OF CUT See Figure 9. Depth of cut affects the rate of feed and the quality of a cut. Using the proper depth of cut can lessen the possibility of damage to the trimmer motor and cutter.A deeper cut requires a slower feed than a shallow one. Mak-ing a cut that is...

Page 16 - ROUTING GROOVES IN A CIRCLE; WORKPIECE

Page 16 Page 17 OPERATION Fig. 12 USING THE WOODWORKING SUB-BASE WITH HANDLES The woodworking sub-base with handles is convenient when routing 4 in. (101.6 mm), 5 in. (127 mm), or 6 in. (152.4 mm) circular grooves. It can also be used when routing grooves parallel to the edge of the workpiece. The h...

Page 17 - ROUTING GROOVES PARALLEL TO AN EDGE; ROUT GROOVE FROM RIGHT TO LEFT

Page 16 Page 17 OPERATION ROUTING GROOVES PARALLEL TO AN EDGE See Figure 13. You can use the scale provided on the woodworking sub-base to cut a straight parallel line up to 1 in. (25.4 mm) from the edge of the workpiece. n The intersection of the horizontal and vertical lines at the center of the w...

Page 18 - MAINTENANCE; GENERAL MAINTENANCE

Page 18 Page 19 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation ...

Page 19 - BRUSH REPLACEMENT; Do not

Page 18 Page 19 Fig. 14 SCREWS TOP COVER BRUSH ASSEMBLY CLAMP SCREWS BRUSH TUBE CLAMPS BLACK LEAD RED LEAD BRUSH ASSEMBLY MAINTENANCE BRUSH REPLACEMENT See Figures 14 - 15. n Unplug the trimmer. n Remove screws from the top cover of the trimmer. n Remove the top cover. n Remove the clamp screws. n R...

Page 20 - • MODEL NUMBER

Page 20 983000-4291-17-06 (REV: 01) • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest...