Ryobi RTS08 - Manuals
User Manual Ryobi RTS08
Summary
3 - English WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “po...
4 - English GENERAL SAFETY RULES Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the wor...
5 - English TABLE SAW SAFETY RULES Provide auxiliary workpiece support to the rear and/or sides of the saw table for long and/or wide workpieces to keep them level. A long and/or wide workpiece has a tendency to pivot on the table’s edge, causing loss of control, saw blade binding and kickback. ...
7 - English SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Safety Alert Indicates a potential personal injury ha...
8 - English ELECTRICAL DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulate...
9 - English GLOSSARY OF TERMS Pilot Hole (drill presses and scroll saws) A small hole drilled in a workpiece that serves as a guide for drilling large holes accurately or for insertion of a scroll saw blade. Push Blocks (jointer planers) Device used to feed the workpiece over the jointer planer cutt...
10 - English FEATURES PRODUCT SPECIFICATIONS Blade Arbor .............................................................. 5/8 in.Blade Diameter ......................................................8-1/4 in.Blade Tilt ................................................................. 0˚ - 45˚ Rating .....
11 - English KNOW YOUR TABLE SAW See Figures 2 - 3. The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating featur...
12 - English FEATURES HEIGHT/BEVEL ADJUSTING HANDWHEEL - Located on the front of the saw, use this handwheel to lower and raise the blade for height adjustments or blade replacement. This handwheel also makes the adjustment for bevel angles easy. MITER GAUGE - The miter gauge aligns the wood for a c...
13 - English The following tools (not included or drawn to scale) are needed for assembly and making adjustments: TOOLS NEEDED Fig. 5 FRAMING SQUARE PHILLIPS SCREWDRIVER FLATHEAD SCREWDRIVER SOCKET WRENCH AND SOCKETS (8 mm and 13 mm) COMBINATION SQUARE C-CLAMPS 13mm WRENCH
LOOSE PARTS 14 - English The following items are included with your table saw: Fig. 6 A. Blade Guard with Anti-kickback Pawls.................... 1 B. Handle Assembly ..................................................... 1 C. Handle End Cap ....................................................... 1 D...
15 - English UNPACKING This product requires assembly. Carefully lift saw from the carton and place it on a level work surface. NOTE: This tool is heavy. To avoid back injury, keep your knees bent and lift with your legs, not your back, and get help when needed. WARNING: Do not use this product if...
16 - English ASSEMBLY MOUNTING HOLES See Figure 7. The table saw must be mounted to a firm supporting surface such as a workbench or leg stand. Four bolt holes have been provided in the saw’s base for this purpose. To mount the saw to a work bench, insert bolts that are of sufficient length to accom...
17 - English ASSEMBLY CHANGING RIVING KNIFE POSITIONS See Figure 10. This saw is shipped with a riving knife that should be placed in the “down” position for non-through cutting and must be placed in the “up” position for all other cutting operations. CAUTION: Use caution when reaching inside the th...
18 - English ASSEMBLY CHECKING SAW BLADE INSTALLATION See Figure 11. NOTICE: To work properly, the saw blade teeth must point down toward the front of the saw. Failure to heed this warning could cause damage to the saw blade, the saw, or the workpiece. Unplug the saw. Remove the blade wrench fro...
19 - English ASSEMBLY INSTALLING THE BLADE GUARD See Figures 12 - 13. WARNING: Always install the blade guard onto the riving knife in the “up” position to provide proper blade coverage. Installing the guarding components onto the riving knife in any other position will prevent them from working as ...
20 - English Fig. 14 ASSEMBLY TO CHECK AND ALIGN THE RIVING KNIFEAND SAW BLADE See Figures 14 - 15. To check alignment of the riving knife: Unplug the saw. Raise the saw blade by turning the height/bevel adjusting handwheel clockwise. Adjust the bevel angle to 0° and lock the bevel locking lev...
21 - English Fig. 17 ASSEMBLY RIP FENCE STORING TABLE SAW ACCESSORIES See Figures 16 - 19. When not in use the rip fence, riving knife, wrenches, blade guard, miter gauge, and push stick may be stored beneath the saw table. Fig. 19 Fig. 18 Fig. 16 BLADE GUARD STORAGE RIP FENCE STORAGE BLADE GUARD BL...
22 - English CAUSES OF KICKBACK Kickback can occur when the blade stalls or binds, kicking the workpiece back toward you with great force and speed. If your hands are near the saw blade, they may be jerked loose from the workpiece and may contact the blade. Obviously, kickback can cause serious inju...
23 - English OPERATION Clean the saw, blade guard, under the throat plate, and any areas where sawdust or scrap workpieces may gather. Keep blade guard, riving knife and ainti-kickback pawls in place and proper operation. The riving knife must be in alignment with the blade and the pawls must st...
24 - English OPERATION 3/4 in. 21 in. 3 1/2 in. WORKPIECE SUPPORTS See Figure 22. When cutting with your table saw, make sure that the workpiece you are cutting is properly supported. Properly supporting the workpiece throughout the cutting process not only improves the accuracy of the cut but also ...
25 - English HOW TO MOUNT A FEATHERBOARD See Figure 26. Completely lower the saw blade. Position the rip fence to the desired adjustment for the cut to be performed and lock. Place the workpiece against the fence and over the saw blade area. Adjust the featherboard to apply resistance to the workpie...
26 - English OPERATION BEVEL RIP CUT RIP CUT CROSS CUT MITER CUT COMPOUND (BEVEL) MITER CUT BEVEL CROSS CUT 1 TYPES OF CUTS See Figure 27. There are six basic cuts: 1) the cross cut, 2) the rip cut, 3) the miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and 6) the compound (bevel) miter cut...
27 - English OPERATION TO CHANGE BLADE DEPTH See Figure 28. The blade depth should be set so that the outer points of the blade are higher than the workpiece by approximately 1/8 in. to 1/4 in. but the lowest points (gullets) are below the top surface. Turn the bevel lock lever to the right. Rai...
28 - English OPERATION FRONT RAIL Fig. 33 Fig. 32 Fig. 31 RIP FENCE LOW FENCE RIP FENCE TO USE THE RIP FENCE See Figures 31 and 32. WARNING: To reduce the risk of injury, always make sure the rip fence is parallel to the blade before beginning any operation. NOTE: The rip fence included with your sa...
29 - English TO USE THE MITER GAUGE See Figure 34. The miter gauge provides greater accuracy in angled cuts. For very close tolerances, test cuts are recommended.The miter gauge can be turned 60° to the right or left. Loosen the lock knob. With the miter gauge in the miter gauge groove, rotate t...
30 - English If the distances are different: Remove the blade guard and riving knife. Raise the blade by turning the height/bevel adjusting handwheel clockwise. Loosen the locking bolts by turning towards the left. NOTE: The bolts are located above the height/bevel adjusting handwheel and under ...
31 - English OPERATION Always place the workpiece against the face of the miter gauge body when making cuts. To prevent the workpiece from moving, you can attach a piece of sandpaper to the miter gauge body face. NOTE: It is recommended that you place the piece to be saved on the same side of the bl...
32 - English OPERATION REPETITIVE CROSS CUT Fig. 40 STOP BLOCK To make repetitive cross cuts: A stop block can be used as a cut-off gauge to make repeti-tive cross cuts of the same length without having to mark the workpiece for each cut. The end of a stop block should always be in front of the blad...
33 - English Turn the saw on. Position the workpiece flat on the table with the edge flush against the rip fence. Let the blade build up to full speed before feeding the workpiece into the blade. Using a push stick and/or push blocks, slowly feed the workpiece toward the blade. Stand slightly ...
35 - English Fig. 46 BEVEL RIP CUT RIP FENCE SCALE BLADE ANGLED MAKING A BEVEL RIP CUT See Figure 46. WARNING: Make sure the blade guard assembly is installed and working properly to avoid serious personal injury. WARNING: The rip fence must be on the right side of the blade to avoid trapping the wo...
36 - English MAKING A COMPOUND (BEVEL) MITER CUT See Figure 47. WARNING: Make sure the blade guard assembly is installed and working properly to avoid possible serious injury. Remove the rip fence. Unlock the bevel locking lever. Adjust the bevel angle to the desired setting. Lock the bevel ...
37 - English Fig. 48 LARGE PANEL CUT MAKING A LARGE PANEL CUT See Figure 48. Make sure the saw is properly secured to a work surface to avoid tipping from the weight of a large panel. WARNING: Make sure the blade guard assembly is installed and working properly to avoid possible serious injury. WARN...
38 - English MAKING A NON-THROUGH CUT See Figure 49. WARNING: DO NOT install dado blades on this machine. The arbor shaft has insufficient threads to mount a dado blade. Mounting a dado blade could result in the risk of serious personal injury. Non-through cuts (made with a standard 8-1/4 in. blade)...
39 - English WARNING: Before performing any adjustment, make sure the tool is unplugged from the power supply and the top button on the switch is not depressed. Failure to heed this warning could result in serious personal injury. To avoid unnecessary set-ups and adjustments, a good practice is to c...
40 - English ADJUSTMENTS After installation, adjust the rip scale indicator to account for the kerf and thickness of the blade. Refer to To Set the Rip Fence Scale Indicator to the Blade in the Operation section of this manual. In cutting operations, the scale will be set to the side of the blade wh...
41 - English ADJUSTMENTS Repeat above steps to readjust and recheck blade angle as needed. Once blade is 45° to the table: Check bevel indicator. If indicator is not pointing to the 45º mark on the bevel scale, loosen the indicator adjusting screw and adjust indicator. Retighten screws. When...
42 - English WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1 during product operation. If operation is dusty, also wear a dust mas...
43 - English Look for these accessories where you purchased this product or call 1-800-525-2579: Stand Assembly ..........................................................................................................................................089240046001 WARNING: Current attachments and ac...
44 - English TROUBLESHOOTING PROBLEM CAUSE SOLUTION Cutting binds or burns work. Blade is dull.Blade is heeling. Work is fed too fast.Rip fence is misaligned.Workpiece is warped. Riving knife is out of alignment. Replace or sharpen blade.See Adjusting the Blade Parallel to the Miter Gauge Groove (Re...
3 − Français AVERTISSEMENT : Lire les avertissements de sécurité, les instructions et les précisions et consulter les illustrations fournis avec cet outil électrique. Le fait de ne pas se conformer à l’ensemble des consignes présentées ci-dessous risque d’entraîner des décharges électriques, un ince...
4 − Français RÈGLES DE SÉCURITÉ GÉNÉRALES personnes n’ayant pas reçu des instructions adéquates, les outils sont dangereux. Entretenir les outils motorisés et accessoires. Vérifier qu’aucune pièce mobile n’est mal alignée ou bloquée, qu’aucune pièce n’est brisée et s’assurer qu’aucun autre problèm...
5 − Français RÈGLES DE SÉCURITÉ SCIE À TABLE ainsi peut provoquer un contact accidentel avec la lame en mouvement. Assurer un soutien auxiliaire pour la pièce à travailler à l’arrière ou sur les côtés de la scie à table pour les morceaux longs ou larges pour qu’ils restent de niveau. Les pièces à ...
7 − Français SYMBOLES Certains des symboles ci-dessous peuvent être utilisés sur l’outil. Veiller à les étudier et à apprendre leur signification. Une interprétation correcte de ces symboles permettra d’utiliser l’outil plus efficacement et de réduire les risques. SYMBOLE NOM DÉSIGNATION / EXPLICATI...
8 − Français CARACTÉRISTIQUES ÉLECTRIQUES DOUBLE ISOLATION La double isolation est un dispositif de sécurité utilisé sur les outils à moteur électriques, éliminant le besoin de cordon d’alimentation habituel à trois fils avec terre. Toutes les pièces métalliques exposées sont isolées des composants ...
9 − Français GLOSSAIRE Trou pilote (perceuses à colonne et scie à découper) Petit trou pratiqué dans une pièce servant de guide pour assurer la précision d’un trou de plus grand diamètre ou pour l’insertion d’une lame de scie à découper. Blocs poussoirs (pour dégauchisseuses/raboteuses) Dispositifs ...
10 − Français CARACTÉRISTIQUES FICHE TECHNIQUE Axe de lame ................................................16 mm (5/8 po)Diamètre de la lame........................... 209,5 mm (8-1/4 po)Inclinaison de la lame .............................................. 0˚ - 45˚Tension ..............................
12 − Français CARACTÉRISTIQUES VOLANT DE RÉGLAGE DE HAUTEUR / BISEAU - Situé sur le devant de la scie, ce volant permet d’abaisser et relever la lame pour effectuer les réglages ou les remplacements. Il permet également de régler facilement l’angle de biseau. GUIDE D’ONGLET - Le guide d’onglet align...
13 − Français OUTILS NÉCESSAIRES Les outils suivants (non inclus ou dessiné pour escalader) sont nécessaires pour effectuer l’assemblage et les réglages : ÉQUERRE DE CHARPENTIER TOURNEVIS PHILLIPS TOURNEVIS PLAT CLÉ À DOUILLES ET DOUILLES (8 mm et 13 mm) ÉQUERRE COMBINÉE SERRE-JOINTS CLÉ (13mm) Fig....
PIÈCES DÉTACHÉES 14 − Français Les articles suivant sont inclus avec la scie à table : Fig. 6 A. Garde de lame avec griffes antiretour...................... 1 B. Ensemble de poignée .............................................. 1 C. Capuchon du bout de la poignée ............................ 1 D. C...
15 − Français DÉBALLAGE Ce produit doit être assemblé. Sortir la scie du carton avec précaution et la poser une un plan de travail stable. NOTE : Cet outil est lourd. Pour éviter des problèmes lombaires, garder les genous pliés, soulever avec les jambes, pas avec le dos et demander de l’aide lorsq...
16 − Français ASSEMBLAGE TROUS DE MONTAGE Voir la figure 7. La scie à table doit être montée solidement sur un plan de travail ferme, tel qu’un établi ou un stand. Pour ce faire, la cadre de la scie comporte quatre trous. Pour le montage sur un établi, les boulons doivent être assez longs pour trave...
17 − Français ASSEMBLAGE POUR CHANGER ENTRE UNE COUTEAU DIVISEUR Voir la figure 10. Cette scie est expédiée avec le couteau diviseur a placé dans la coupe de non traversante ou « en bas » la position et doit être en.« en haut » la position pour toutes autres opérations de coupe. ATTENTION : Faire pr...
19 − Français ASSEMBLAGE INSTALLATION DE PROTÈGE-LAME Voir les figures 12 et 13. AVERTISSEMENT : Toujours installer le protège-lame et les griffes antirebond sur le couteau diviseur vers le haut afin de protéger adéquatement la lame. L’installation de composants protecteurs sur le couteau diviseur d...
20 − Français ASSEMBLAGE VÉRIFICATION ET ALIGNEMENT DU COUTEAU DIVISEUR ET LA LAME Voir les figures 14 et 15. Vérification de l’alignement du couteau diviseur : Débrancher la scie. Élever la lame de scie en tournant le volant de réglage de hauteur / biseau vers la droite. Régler l’angle du bis...
22 − Français CAUSES DE REBONDS Un rebond peut se produire lorsque la lame se bloque ou se coince et propulse violemment la pièce à couper en direction de l’opérateur. Si les mains se trouvent près de lame, elles pourraient être éjectées de la pièce et entrer en contact avec la lame. Il est évident ...
23 − Français UTILISATION L’usage d’un cale-guide aidera la prise la pièce assurément contre la table de scie ou le guide. Nettoyer la scie, le protège-lame, sous la plaque à gorge, et n’importe quels sciure où n’importe quelle poussière de scie ou les pièces de fragment peuvent rassembler. Ma...
24 − Français UTILISATION SUPPORTS DE LA PIÈCE À TRAVAILLER Voir la figure 22. En coupant avec votre scie à table, veiller à ce que la pièce à couper soit correctement soutenue. Bien soutenir la pièce à travailler lors de la découpe permet non seulement d’améliorer la précision de coupe, mais aussi ...
25 − Français BLOC- POUSSOIR CALE-GUIDE LEVIER DE VERROUILLAGE DE LA COUPE EN BISEAU BÂTON POUSSOIR COMMENT INSTALLER UNE CALE-GUIDE Voir la figure 26. Abaisser complètement la lame. Placer le guide longitudinal à la distance voulue de la lame pour la coupe et le verrouiller. Placer la pièce à coupe...
26 − Français UTILISATION COUPE LONGITUDINALE EN BISEAU COUPE LONGITUDINALE COUPE TRANSVERSALE COUPE D’ONGLET COUPE D’ONGLET COMPOSÉ (EN BISEAU) COUPE TRANSVERSALE EN BISEAU 1 TYPES DE COUPE Voir la figure 27. Il y a six principaux types de coupe : 1) coupe transversale, 2) coupe longitudinale, 3) c...
27 − Français UTILISATION Retirer les noeuds décollés à l’aide d’un marteau avant d’effectuer la coupe. Toujours utiliser un support adéquat sous une planche à la sortie de la scie. RÉGLAGE DE LA PROFONDEUR DE LAME Voir la figure 28. La profondeur de coupe doit être réglée pour que les pointes e...
28 − Français UTILISATION UTILISATION DU GUIDE LONGITUDINAL Voir les figures 31 et 32. AVERTISSEMENT : Pour réduire le risque de blessures, toujours vérifier que le guide longitudinal est parallèle à la lame avant de commencer une coupe. NOTE : Le guide longitudinal fourni avec la scie possède un gu...
29 − Français UTILISATION DU GUIDE D’ONGLET Voir la figure 34. Le guide d’onglet permet d’effectuer des coupes en biais de grande précision. Il est recommandé d’effectuer des coupes d’essai lorsque les tolérances sont réduites.Le guide d’onglet peut être tourné de 60° à droite ou à gauche. Desserr...
30 − Français Si les distances mesurées sont différentes : Retirer la garde de lame, le couteau diviseur et griffes antirebond. Relever la lame au maximum en tournant le volant de réglage de hauteur / biseau vers la droite. Desserrer les boulons de verrouillage en tournant vers la gauche. NOTE :...
32 − Français UTILISATION Pour effectuer des coupes transversales répétitives : Un bloc d’arrêt peut servir comme guide d’arrêt pour réaliser des coupes transversales répétitives de même longueur sans avoir à marquer la pièce à travailler pour chaque coupe. L’extrémité d’un bloc d’arrêt doit toujour...
36 − Français COUPE D’ONGLET COMPOSÉ (EN BISEAU) Voir la figure 47. AVERTISSEMENT : Afin d’éviter le risque de blessures graves, s’assurer que la garde de lame est installée et fonctionne correctement. Retirer le guide longitudinal. Désengager le levier de verrouillage de biseau. Ajuster le gu...
37 − Français COUPE D’UNE PIÈCE DE GRANDE TAILLE Voir la figure 48. S’assurer que la scie est solidement assujettie sur le plan de travail, afin que le poids d’une grande planche ne risque pas de la faire basculer. AVERTISSEMENT : Afin d’éviter le risque de blessures graves, s’assurer q u e l a g a ...
38 − Français COUPE NON TRAVERSANTE Voir la figure 49. AVERTISSEMENT : NE PAS installation lames à rainer sur cette machine. L’ axe de lame a des filetage insuffisants pour installation une lame à rainer. Monter une lame à rainer pourrait avoir pour résultat le risque des blessures graves. Les coupe...
39 − Français AVERTISSEMENT : Avant d’effectuer tout réglage, s’assurer que l’outil est débranché et le bouton supérieur du commutateur n’est pas enfoncé. Le non-respect de cet avertissement pourrait entraîner des blessures graves. Pour éviter des ajustements inutiles, il est bon de vérifier les rég...
40 − Français RÉGLAGES Après l’installation, ajuster l’indicateur de l’échelle de refente pour tenir compte du trait et de l’épaisseur de la lame. Rapportez-vous à Pour régler l’échelle graduée sur la lame dans la section Utilisation dans ce manuel. Lors de la coupe, l’échelle doit être placée du cô...
42 − Français PLAQUES LEVIER DE BLOCAGE AVERTISSEMENT : Utiliser exclusivement des pièces d’origine pour les réparations. L’usage de toute autre pièce pourrait créer une situation dangereuse ou endommager l’outil. AVERTISSEMENT : Toujours porter une protection oculaire certifiée conforme à la norme ...
43 − Français ENTRETIEN Rechercher ces accessoires où vous avez acheté ce produit ou en appelant au 1-800-525-2579 : Ensemble de stand ...............................................................................................................................................089240046001 AVERTIS...
3 − Español ADVERTENCIA: Lea todas las advertencias, instrucciones, ilustraciones y especificaciones proporcionadas con esta herramienta eléctrica. No seguir las instrucciones indicadas a continuación puede provocar descargas eléctricas, incendios o lesiones graves. Guarde todas las advertencias e i...
4 − Español REGLAS DE SEGURIDAD GENERALES que la reparen antes de usarla. Numerosos accidentes son causados por herramientas eléctricas mal cuidadas. Mantenga las herramientas de corte afiladas y limpias. Las herramientas de corte bien cuidadas y con bordes bien afilados, tienen menos probabilidad...
5 − Español REGLAS DE SEGURIDAD SIERRA DE MESA Proporcione apoyo auxiliar para la pieza de trabajo en la parte trasera y los laterales de la mesa de la sierra cuando corte piezas largas o anchas, a fin de mantenerlas niveladas. Las piezas de trabajo largas o anchas tienden a pivotar con el borde d...
7 − Español SÍMBOLOS Es posible que se empleen en esta herramienta algunos de los siguientes símbolos. Le suplicamos estudiarlos y aprender su significado. Una correcta interpretación de estos símbolos le permitirá utilizar mejor y de manera más segura la herramienta. SÍMBOLO NOMBRE DENOMINACIÓN/EXP...
8 − Español ASPECTOS ELÉCTRICOS DOBLE AISLAMIENTO El doble aislamiento es una característica de seguridad de las herramientas eléctricas, la cual elimina la necesidad de usar el típico cordón eléctrico de tres conductores con conexión a tierra. Todas las partes metálicas expuestas están aisladas de ...
9 − Español GLOSARIO DE TÉRMINOS es un corte en el cual la hoja no corta la pieza de trabajo en dos pedazos. Agujero guía (taladradoras de columna y sierras caladoras) Es un agujero pequeño taladrado en una pieza de trabajo, el cual sirve como guía para taladrar con precisión agujeros más grandes o ...
10 − Español CARACTERÍSTICAS ESPECIFICACIONES DEL PRODUCTO Árbol de la hoja de corte ........................ 16 mm (5/8 pulg.)Diámetro de la hoja ....................... 209,5 mm (8-1/4 pulg.)Inclinación de la hoja ............................................... 0˚ - 45˚ Especificaciones eléctricas...
11 − Español FAMILIARÍCESE CON LA SIERRA DE MESA Vea las figuras 2 y 3. El uso seguro que este producto requiere la comprensión de la información impresa en la herramienta y en el manual del operador así como ciertos conocimientos sobre el proyecto a realizar. Antes de usar este producto, familiaríc...
12 − Español CARACTERÍSTICAS VOLANTE DE AJUSTE DE ALTURA Y BISEL - Este volante, situado en la parte delantera de la sierra, sirve para subir y bajar la hoja con el fin de efectuar ajustes a la altura de la misma, o reemplazarla. Este volante también facilita el ajuste del ángulo de biselado. GUÍA D...
13 − Español HERRAMIENTAS NECESARIAS ESCUADRA DE CARPINTERO LLAVE 13 mm DESTORNILLADOR DE PUNTA PLANA DESTORNILLADOR DE CABEZA PHILLIPS ESCUADRA DE COMBINACIÓN LLAVE DE CASQUILLO Y CUBOS CUADRADOS (8 mm y 13 mm) PRENSAS EN C Para armar la unidad y efectuar ajustes se necesitan las siguientes herrami...
PIEZAS SUELTAS 14 − Español Con la sierra de mesa vienen incluidos los siguientes artículos: Fig. 6 A. Protección de la hoja con trinquetes anticontragolpe ....................................... 1 B. Conjunto del mango ................................................ 1 C. Tapa del extremo del mango...
15 − Español DESEMPAQUETADO Este producto requiere armarse. Levante cuidadosamente de la caja la sierra y colóquela sobre una superficie de trabajo nivelada. NOTA: Esta herramienta es pesada. Para evitar lesionarse la espalda, mantenga dobladas las rodillas, levante con las piernas, no con la espa...
16 − Español ARMADO AGUJEROS DE MONTAJE Vea la figura 7. La sierra de mesa debe montarse en una superficie de soporte firme, como un banco de trabajo o un pedestal de patas. Hay cuatro agujeros para perno en la armazón de la sierra para este fin. Si se atornilla a un banco de trabajo, los pernos deb...
18 − Español ARMADO PARA REVISAR LA INSTALACIÓN DE LA HOJA DE LA SIERRA Vea la figura 11. AVISO: Para funcionar correctamente, los dientes de la hoja deben apuntar hacia la parte frontal de la sierra, hacia abajo. La inobservancia de esta advertencia podría causar daños a la hoja de la sierra, la si...
19 − Español ARMADO PARA INSTALAR EL PROTECCIÓN DE LA HOJA Vea las figuras 12 y 13. ADVERTENCIA: Instale siempre la protección de la hoja y las garras que no permiten el retroceso en la cuchilla separadora en la posición “ascendente” para suministrar una cobertura de hoja adecuada. Instalar los comp...
21 − Español PROTECCIÓN DE LA HOJA ARMADO ALMACENAMIENTO DE ACCESORIOS DE LA SIERRA DE MESA Vea las figuras 16 a 19. Cuando no estén en uso, la guía de corte al hilo, la cuchilla separadora, las llaves, la protección de la hoja, el medidor de inglete, y el palo empujador pueden guardarse debajo de l...
22 − Español CAUSAS DE LOS CONTRAGOLPES El contragolpe puede ocurrir cuando la hoja se atasca o dobla, lanzando la pieza de trabajo hacia atrás, hacia usted, con gran fuerza y velocidad. Si tiene las manos cerca de la hoja de la sierra, pueden soltarse de la pieza de trabajo y tocar la hoja. Obviame...
23 − Español FUNCIONAMIENTO Limpie el sierra, protección de la hoja, bajo el placa de la garanta, y bajo cualquier área donde sierra o pieza de trabajo o aserrín puede reunir Mantenga la protección de la hoja, la cuchilla separadora y los trinquetes anticontragolpe en su lugar y en un estado de ...
24 − Español FUNCIONAMIENTO SOPORTES DE LA PIEZA DE TRABAJO Vea la figura 22. Cuando corte con la sierra de mesa, asegúrese de que la pieza de trabajo esté bien sujetada. El soporte adecuado de la pieza de trabajo durante el proceso de corte no solo mejora la precisión del corte, sino que también pe...
25 − Español FORMA DE MONTAR UN PEINE DE SUJECIÓN Vea la figura 26. Baje completamente la hoja de la sierra. Coloque la guía de corte al hilo a la distancia requerida según requiera el corte deseado y asegúrela. Coloque la pieza de trabajo contra la guía, en el área de la hoja de corte. Ajuste el pe...
26 − Español FUNCIONAMIENTO TIPOS DE CORTES Vea la figura 27. Existen seis cortes básicos: 1) el corte transversal, 2) el corte al hilo, 3) el corte a inglete, 4) el corte transversal en bisel, 5) el corte al hilo en bisel y 6) el corte a inglete combinado (en bisel). Todos los otros cortes son comb...
27 − Español FUNCIONAMIENTO PARA CAMBIAR LA PROFUNDIDAD DE LA HOJA Vea la figura 28. Se debe ajustar la profundidad de la hoja de la sierra de manera que las puntas exteriores de la hoja queden más elevadas que la pieza de trabajo de 3,2 mm a 6,4 mm (1/8 pulg. a 1/4 pulg.) aproximadamente, pero los ...
28 − Español FUNCIONAMIENTO PARA USAR LA GUÍA DE CORTE AL HILO Vea las figuras 31 y 32. ADVERTENCIA: Para reducir el riesgo de sufrir lesiones, siempre asegúrese de que la guía de corte al hilo esté paralela a la hoja, antes de iniciar cualquier operación. NOTA: La guía de corte al hilo incluida con...
29 − Español PARA USAR LA GUIA DE INGLETES Vea la figura 34. La guía de ingletes brinda una gran precisión en los cortes en ángulo. Para efectuar cortes con tolerancias muy estrechas se recomienda efectuar cortes de prueba.El calibrador de ingletes puede girarse 60° a la derecha o izquierda. Afloj...
30 − Español Si ambas distancias medidas son diferentes: Retirar la protección de la hoja, el cuchilla separadora y trinquetes anti contragolpe. Eleve lo más posible la hoja con un giro de la volante de ajuste de altura y bisel. Afloje los pernos de seguridad girándolos hacia la izquierda. NOTA:...
31 − Español FUNCIONAMIENTO Coloque siempre la pieza de trabajo contra la cara del cuerpo del medidor de inglete al realizar cortes. Para evitar que la pieza de trabajo se mueva, puede colocar un pedazo de papel de lija en la cara del cuerpo del medidor de inglete. NOTA: Se recomienda colocar la pie...
32 − Español FUNCIONAMIENTO Para realizar cortes transversales repetitivos, siga estos pasos: Se puede usar un bloque de detención como indicador de corte para realizar cortes transversales repetitivos de la misma longitud sin tener que marcar la pieza de trabajo para hacer cada corte. El extremo de...
34 − Español CÓMO EFECTUAR CORTES A INGLETE Vea la figura 43. ADVERTENCIA: Asegúrese de que esté instalado y funcione adecuadamente el conjunto de protección de la hoja para evitar posibles lesiones graves. Desmonte la guía de corte al hilo. Ajuste la hoja a la profundidad correcta para la pieza...
35 − Español CÓMO EFECTUAR CORTES AL HILO EN BISEL Vea la figura 46. ADVERTENCIA: Asegúrese de que esté instalado y funcione adecuadamente el conjunto de protección de la hoja para evitar lesiones graves. ADVERTENCIA: La guía de corte al hilo debe estar del lado derecho de la hoja para evitar atrapa...
36 − Español CÓMO EFECTUAR CORTES A INGLETE COMBINADOS (EN BISEL) Vea la figura 47. ADVERTENCIA: Asegúrese de que esté instalado y funcione adecuadamente el conjunto de protección de la hoja para evitar posibles lesiones graves. Desmonte la guía de corte al hilo. Afloje la palanca de fijación de...
37 − Español CÓMO CORTAR UN PANEL GRANDE Vea la figura 48. Asegúrese de que la sierra esté debidamente asegurada a una superficie de trabajo para evitar cualquier volcamiento producido por un panel grande. ADVERTENCIA: Asegúrese de que esté instalado y funcione adecuadamente el conjunto de protecció...
38 − Español CÓMO EFECTUAR UN CORTE SIN TRASPASO Vea la figura 49. ADVERTENCIA: NO installar hojas de ranurar en esta máquina. El polea del árbol tiene rosca insuficientes para instalar una hoja de ranura. Montar una hoja de ranura podría tener como resultado el riesgo de puede lesiones serias. Pued...
39 − Español ADVERTENCIA: Antes de efectuar cualquier ajuste, asegúrese de que la herramienta esté desconectada del suministro de corriente y que el botón superior del interruptor no esté presionado. La falta de atención a esta advertencia podría causar lesiones corporales graves. Para evitar config...
40 − Español AJUSTES Después de la instalación, ajuste el indicador de escala de corte al hilo para adaptarlo al ancho de corte y el grosor de la hoja. Consulte el apartado Para ajustar a la hoja el indicador de la escala de la guía de corte al hilo en la sección Funcionamiento de este manual. En la...
42 − Español PALANCA PARA BLOQUEAR PLACAS CUCHILLA SEPARADORA ADVERTENCIA: Al dar servicio a la unidad, sólo utilice piezas de repuesto idénticas. El empleo de piezas diferentes puede causar un peligro o dañar el producto. ADVERTENCIA: Siempre póngase protección ocular con la marca de cumplimiento d...
43 − Español MANTENIMIENTO VERTEDERO DE ASERRÍN Vea la figura 58. Esta sierra incluye un vertedero de aserrín práctico para descargar el aserrín. Puede conectar una aspiradora común al vertedero de aserrín, ubicado debajo de la parte trasera de la sierra.Durante períodos de uso prolongado, el verted...
Ryobi Table Saws Manuals
-
Ryobi PBLTS01B
User Manual
-
Ryobi PBLTS01K
User Manual
-
Ryobi PBLTS01K-PBP004
User Manual
-
Ryobi PBLTS01K-PBT01B
User Manual
-
Ryobi PGC21B-A06F551
User Manual
-
Ryobi PGC21K
User Manual
-
Ryobi PGC21K-A06F551
User Manual
-
Ryobi RTS12
User Manual
-
Ryobi RTS23
User Manual
-
Ryobi RTS23-PBLDD01K
User Manual
-
Ryobi RTS23-RHTM25
User Manual