Ryobi R10633- Manuals

Page 6 ■ To reduce the risk of damage to charger body andcord, pull by charger plug rather than cord whendisconnecting charger. Following this rule will reduce the risk of serious personal injury. ■ Make sure cord is located to that it will not be steppedon, tripped over, or otherwise subjected to d...

Page 7 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, andthe explanations with them, deserve your careful attention and understanding. The safety warnings donot by themselves eliminate any danger. The instructions or warnings they give are not sub...

Page 8 KNOW YOUR CORDLESS CIRCULAR SAW See Figure 1. Before attempting to use any tool, familiarize yourself withall operating features and safety requirements. Features include easily operated bevel cut and depth of cutadjustment mechanisms; positive 0 ° bevel stop; spindle lock; and blade wrench s...

Page 9 LED FUNCTION OF CHARGER See Figure 2. LED WILL BE LIGHTED TO INDICATE STATUS OFCHARGER AND BATTERY PACK: ■ Red LED lighted = Fast Charging Mode ■ Green LED lighted = Fully Charged Battery Pack ■ Yellow and Green LED Lighted = Control Charge or Defective Battery Pack. CHARGING BATTERY PACK The...

Page 10 WARNING: Always remove battery pack from your saw when youare assembling parts, making adjustments, assemblingor removing blades, cleaning, or when not in use.Removing battery pack will prevent accidental startingthat could cause serious personal injury. TO REMOVE BATTERY PACK ■ Locate latch...

Page 11 45 4 5 50 5 0 30 30 22 22 1 1 2 3 0 45 Fig. 6 BLADE SCREW BLADE WRENCH SPINDLE LOCK BUTTON ■ Fit saw blade inside lower blade guard and onto spindle. NOTE: The saw teeth point upward at the front of saw as shown in figure 5. ■ Replace outer blade washer. ■ Depress spindle lock button, then r...

Page 12 KICKBACK See Figure 8. The best guard against kickback is to avoid dangerouspractices. Kickback occurs when the blade stalls rapidly and the saw isdriven back towards you. Blade stalling is caused by anyaction which pinches the blade in the wood. WARNING: To avoid kickback, release switch im...

Page 13 ■ When making a cut use steady, even pressure. Neverforce cuts. ■ Do not cut warped or wet lumber. ■ Always hold your saw firmly with both hands and keepyour body in a balanced position so as to resist the forcesof kickback should it occur. When using your saw, always stay alert and exercise...

Page 14 TO HELP MAINTAIN CONTROL: ■ Always support your workpiece near the cut. ■ Support your workpiece so the cut will be on your left. ■ Clamp your workpiece so it will not move during the cut. Place your workpiece with its good side down. NOTE: The good side is the side on which appearance is im...

Page 15 TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cutwith the outer blade guide notch on the saw base asshown in figure 17. Since blade thicknesses vary, always make a trial cut inscrap material along a guideline to determine how much, ifany, the guideline must b...

Page 16 TO BEVEL CUT The angle of cut of your saw may be adjusted to any desiredsetting between zero and 50 ° . NOTE: When making cuts at 50 ° , blade should be set at full depth of cut. When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut....

Page 17 1 2 45 0 0 15 22 30 45 50 45 4 5 50 5 0 30 30 22 22 POSITIVE 0 ° BEVEL STOP See Figure 21. Your saw has a positive 0 ° bevel stop, that has been factory adjusted to assure 0 ° angle of your saw blade when making 90 ° cuts. However, misalignment can occur during shipping. TO CHECK ■ Remove ba...

Page 19 WARNING: When servicing, use only identical replacement parts.Use of any other part may create a hazard or causeproduct damage. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contactwith plastic parts. They contain chemicals t...

983000-192 7-03 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson, SC 29622 Post Office Box 1207 Anderson, SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service,simply contact your nearest R...

Page 6 ■ To reduce the risk of damage to charger body andcord, pull by charger plug rather than cord whendisconnecting charger. Following this rule will reduce the risk of serious personal injury. ■ Make sure cord is located to that it will not be steppedon, tripped over, or otherwise subjected to d...

Page 7 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, andthe explanations with them, deserve your careful attention and understanding. The safety warnings donot by themselves eliminate any danger. The instructions or warnings they give are not sub...

Page 8 KNOW YOUR CORDLESS CIRCULAR SAW See Figure 1. Before attempting to use any tool, familiarize yourself withall operating features and safety requirements. Features include easily operated bevel cut and depth of cutadjustment mechanisms; positive 0 ° bevel stop; spindle lock; and blade wrench s...

Page 9 LED FUNCTION OF CHARGER See Figure 2. LED WILL BE LIGHTED TO INDICATE STATUS OFCHARGER AND BATTERY PACK: ■ Red LED lighted = Fast Charging Mode ■ Green LED lighted = Fully Charged Battery Pack ■ Yellow and Green LED Lighted = Control Charge or Defective Battery Pack. CHARGING BATTERY PACK The...

Page 10 WARNING: Always remove battery pack from your saw when youare assembling parts, making adjustments, assemblingor removing blades, cleaning, or when not in use.Removing battery pack will prevent accidental startingthat could cause serious personal injury. TO REMOVE BATTERY PACK ■ Locate latch...

Page 11 45 4 5 50 5 0 30 30 22 22 1 1 2 3 0 45 Fig. 6 BLADE SCREW BLADE WRENCH SPINDLE LOCK BUTTON ■ Fit saw blade inside lower blade guard and onto spindle. NOTE: The saw teeth point upward at the front of saw as shown in figure 5. ■ Replace outer blade washer. ■ Depress spindle lock button, then r...

Page 12 KICKBACK See Figure 8. The best guard against kickback is to avoid dangerouspractices. Kickback occurs when the blade stalls rapidly and the saw isdriven back towards you. Blade stalling is caused by anyaction which pinches the blade in the wood. WARNING: To avoid kickback, release switch im...

Page 13 ■ When making a cut use steady, even pressure. Neverforce cuts. ■ Do not cut warped or wet lumber. ■ Always hold your saw firmly with both hands and keepyour body in a balanced position so as to resist the forcesof kickback should it occur. When using your saw, always stay alert and exercise...

Page 14 TO HELP MAINTAIN CONTROL: ■ Always support your workpiece near the cut. ■ Support your workpiece so the cut will be on your left. ■ Clamp your workpiece so it will not move during the cut. Place your workpiece with its good side down. NOTE: The good side is the side on which appearance is im...

Page 15 TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cutwith the outer blade guide notch on the saw base asshown in figure 17. Since blade thicknesses vary, always make a trial cut inscrap material along a guideline to determine how much, ifany, the guideline must b...

Page 16 TO BEVEL CUT The angle of cut of your saw may be adjusted to any desiredsetting between zero and 50 ° . NOTE: When making cuts at 50 ° , blade should be set at full depth of cut. When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut....

Page 17 1 2 45 0 0 15 22 30 45 50 45 4 5 50 5 0 30 30 22 22 POSITIVE 0 ° BEVEL STOP See Figure 21. Your saw has a positive 0 ° bevel stop, that has been factory adjusted to assure 0 ° angle of your saw blade when making 90 ° cuts. However, misalignment can occur during shipping. TO CHECK ■ Remove ba...

Page 19 WARNING: When servicing, use only identical replacement parts.Use of any other part may create a hazard or causeproduct damage. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contactwith plastic parts. They contain chemicals t...

983000-192 7-03 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson, SC 29622 Post Office Box 1207 Anderson, SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service,simply contact your nearest R...