Ryobi P400- Manuals

6 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols will allow you to operate the tool better and safer. V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes ...

8 FEATURES Fig. 1 PRODUCT SPECIFICATIONS Motor ......................................................................................................................................................................18 Volt DCOrbits Per Minute ..............................................................

9 FEATURES KNOW YOUR CORNER CAT™ FINISH SANDER See Figure 1. The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operati...

10 OPERATION NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. CHARGING A COOL BATTERY PACK If battery pack is within normal temperature range, the red LED on charger will come on. NOT...

11 Fig. 3 OPERATION CHARGING A HOT BATTERY PACK When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will ...

12 OPERATION Fig. 4 Fig. 5 SANDING SHEET WARNING: Battery tools are always in operating condition. There-fore, switch should always be locked when not in use or carrying at your side. SANDING SHEET AND PAD SELECTION Selecting the correct size grit and type sandpaper is an extremely important step in...

13 OPERATION Fig. 6 WORKPIECE OPERATING THE SANDER See Figure 6 - 7.  Secure the workpiece to prevent it from moving under the sander. WARNING: Unsecured workpieces could be thrown towards the operator, causing injury. WARNING: Keep your head away from the sander and the sanding area. Your hair cou...

15 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, als...

16 983000-62210-25-06 (REV:02) P400 OPERATOR’S MANUAL 18 VOLT CORNER CAT™FINISH SANDER P400 ONE WORLD TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Phone 1-800-525-2579 www.ryobitools.com • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or s...

6 7 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols will allow you to operate the tool better and safer. Read The Operator’s Manual Safety Alert No Hands Symbol No Hands Symbol No Hands Symbol No Hands...

6 7 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical replacement parts. WARNING: SAVE ...

8 9 FEATURES Fig. 1 PRODUCT SPECIFICATIONS Motor ......................................................................................................................................................................18 Volt DCOrbits Per Minute ............................................................

8 9 FEATURES KNOW YOUR CORNER CAT™ FINISH SANDER See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. ON (I) / OFF (O) SWITCH The ON (I) / OFF (O) slide switch is located on the front of the tool. ORBITAL SANDING ACTION The oscillati...

10 11 OPERATION NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. CHARGING A COOL BATTERY PACK If battery pack is within normal temperature range, the red LED on charger will come on. ...

10 11 Fig. 3 OPERATION CHARGING A HOT BATTERY PACK When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this wi...

12 13 OPERATION Fig. 4 Fig. 5 SANDING SHEET WARNING: Battery tools are always in operating condition. There-fore, switch should always be locked when not in use orcarrying at your side. SANDING SHEET AND PAD SELECTION Selecting the correct size grit and type sandpaper is an extremely important step ...

12 13 OPERATION Fig. 6 WORKPIECE OPERATING THE SANDER See Figure 6 - 7. n Secure the workpiece to prevent it from moving under the sander. WARNING: Unsecured workpieces could be thrown towards the operator, causing injury. WARNING: Keep your head away from the sander and the sanding area. Your hair ...

14 15 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, ...

16 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Post Office Box 1207, Anderson, SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com 983000-622 6-05 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nea...