Ryobi HP962- Manuals

Page 2 - TABLE OF CONTENTS; GENERAL SAFETY RULES; Read and understand all instructions.; SAVE THESE INSTRUCTIONS; Keep your work area clean and well lit; Electrical Safety; Use battery operated tool only with specifically; Personal Safety; Use safety equipment. Always wear eye protection.

Page 2 TABLE OF CONTENTS ■ General Safety Rule ................................................................................................................................................ 2-3 ■ Specific Safety Rules/Symbols ...........................................................................

Page 3 - Tool Use and Care; Do not use tool if switch does not turn it on or off.; Service; Do not place battery tools or their batteries near fire; SPECIFIC SAFETY RULES AND/OR SYMBOLS; Do not charge battery tool in a damp or wet location.

Page 3 Tool Use and Care ■ Use clamps or other practical way to secure andsupport the workpiece to a stable platform. Holding the work by hand or against your body is unstable andmay lead to loss of control. ■ Do not force tool. Use the correct tool for your appli-cation. The correct tool will do th...

Page 4 - Important Safety Instructions For Charger; To reduce risk of injury,

Page 4 SPECIFIC SAFETY RULES AND/OR SYMBOLS WARNING: Some dust created by power sanding, sawing, grinding,drilling, and other construction activities contains chemi-cals known to cause cancer, birth defects or other repro-ductive harm. Some examples of these chemicals are: • lead from lead-based pai...

Page 5 - SYMBOL; SYMBOLS

Page 5 SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current --- Direct Current Type or a characteristic of current n 0 No Load Speed Rotational speed, at no load .../min R...

Page 6 - IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES; both; DISPOSAL OF THE EXHAUSTED BATTERY; R E

Page 6 SPECIFICATIONS: HP962 HP1202M Chuck 3/8 in. Keyless 3/8 in. Keyless Motor DC Motor 9.6V DC Motor 12.0V Switch Variable Speed Variable Speed No Load Speed 0 - 550 RPM 0 - 550 RPM Clutch 24 Positions 24 Positions Charger Input 120V, 60 Hz, AC Only 120V, 60 Hz, AC Only Charge Rate 3-6 Hours 3-6 ...

Page 7 - OPERATION; KNOW YOUR DRILL-DRIVER; See

Page 7 5 1 0 OPERATION Fig. 1 KNOW YOUR DRILL-DRIVER See Figure 1. Before attempting to use any tool, familiarize yourself with alloperating features and safety requirements. WARNING: Do not allow familiarity with tools to make you careless.Remember that a careless fraction of a second issufficient ...

Page 8 - SWITCH; The switch trigger can be locked in the; OFF; TO INSTALL BATTERY PACK; Remove battery pack from your drill.

Page 8 5 10 5 1 0 3 OPERATION Fig. 4 Fig. 3 WARNING: If any parts are missing, do not operate tool until themissing parts are replaced. Failure to do so could resultin possible serious personal injury. SWITCH See Figure 3. Your drill starts and stops by depressing and releasing theswitch trigger. Yo...

Page 9 - RIGHT; REVERSIBLE; GRIP; INSTALLING BITS; WRONG

Page 9 5 10 5 10 5 1 0 OPERATION Fig. 5 Fig. 6 Note: Rotate the chuck body in the direction of the arrow marked GRIP to tighten the chuck jaws. DO NOT use a wrench to tighten or loosen the chuck jaws. WARNING: Do not insert drill bit into chuck jaws and tighten as shownin figure 7. This could cause ...

Page 10 - REMOVING BITS; RELEASE; TO ADJUST TORQUE

Page 10 2 0 20 5 10 5 10 OPERATION REMOVING BITS See Figure 6. ■ Place the direction of rotation selector in center position. See Figure 3. This will turn off the power to your drill. ■ Loosen the chuck jaws from drill bit . ■ To loosen: grasp and hold the collar of the chuck withone hand, while rot...

Page 11 - DRILLING; MAG TRAYTM

Page 11 20 15 OPERATION WARNING: Always wear safety goggles or safety glasses with sideshields when operating tool. Failure to do so could resultin objects being thrown into your eyes, resulting inpossible serious injury. DRILLING See Figure 11. When drilling hard, smooth surfaces, use a center punc...

Page 12 - CHUCK REMOVAL; TO RETIGHTEN A LOOSE CHUCK; MALLET

Page 12 5 10 5 10 5 10 OPERATION Fig. 13 Fig. 14 Fig. 15 CHUCK REMOVAL See Figures 13, 14, and 15. ■ Lock the switch trigger by placing the direction of rotationselector in center position. See Figure 3. ■ Insert a 5/16 inch or larger hex key into the chuck ofyour drill and tighten the chuck jaws se...

Page 13 - MAINTENANCE; DO NOT ABUSE POWER TOOLS.; Abusive practices can; Ryobi Authorized Service Center.; For; BATTERIES; DISPOSAL OF; . Do not disassemble the battery

Page 13 MAINTENANCE WARNING: When servicing use only identical Ryobi replacementparts. Use of any other parts may create a hazard or causeproduct damage. Avoid using solvents when cleaning plastic parts. Mostplastics are susceptible to damage from various types ofcommercial solvents and may be damag...

Page 14 - MODEL NUMBERS

OPERATOR'S MANUALCORDLESS DRILL-DRIVERMODEL NOS. HP962 / HP1202M 972000-873 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service,simply contact your nearest Ryobi Authorized Service Center. Be sure to provide allpertinent facts when you call or visit....