Ryobi HP1201M- Manuals

Page 2 - TABLE OF CONTENTS; TYPICAL APPLICATIONS

Page 2 TABLE OF CONTENTS ■ Table Of Contents/Typical Applications. ................................................................................ 2 ■ Rules For Safe Operation ................................................................................................... 3-5 A. Precautions On U...

Page 3 - RULES FOR SAFE OPERATION; READ ALL INSTRUCTIONS

Page 3 RULES FOR SAFE OPERATION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and theexplanations with them, deserve your careful attention and understanding. The safety warnings do not bythemselves eliminate any danger. The instructions or warni...

Page 5 - SAVE THESE INSTRUCTIONS

Page 5 RULES FOR SAFE OPERATION (Continued) ■ To reduce risk of damage to electric plug and cord,pull by the body rather than the cord whendisconnecting charger/charging assembly. ■ Make sure cord is located so that it will not bestepped on, tripped over, or otherwise subjectedto damage or stress. ■...

Page 6 - R E

Page 6 SPECIFICATIONS: Model HP1201M Chuck 3/8 in. Keyless Motor DC Motor 12.0V Switch Variable Speed No Load Speed 0 - 550 RPM Clutch 24 Positions Charger Input 120V, 60 Hz, AC Only Charge Rate 3-6 Hours IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES When using your drill-driver continuously, t...

Page 7 - OPERATION; KNOW YOUR DRILL-DRIVER

Page 7 OPERATION Fig. 1 KNOW YOUR DRILL-DRIVER See Figure 1. Before attempting to use any tool, familiarize yourself with alloperating features and safety requirements. WARNING: Do not allow familiarity with tools to make you careless.Remember that a careless fraction of a second issufficient to inf...

Page 8 - SWITCH

Page 8 2 4 6 10 8 6 2 3 10 4 8 OPERATION Fig. 4 Fig. 3 WARNING: If any parts are missing, do not operate tool until themissing parts are replaced. Failure to do so could resultin possible serious personal injury. SWITCH See Figure 3. Your drill starts and stops by depressing and releasing theswitch ...

Page 9 - RIGHT

Page 9 2 4 6 8 2 4 6 8 2 4 6 8 10 OPERATION Fig. 5 Fig. 6 Note: Rotate the chuck body in the direction of the arrowmarked GRIP to tighten the chuck jaws. DO NOT use awrench to tighten or loosen the chuck jaws. WARNING: Do not insert drill bit into chuck jaws and tighten as shownin figure 7. This cou...

Page 10 - REMOVING BITS; BIT STORAGE

Page 10 16 18 22 20 2 4 6 8 10 2 4 6 8 2 4 6 8 OPERATION REMOVING BITS See Figure 6. ■ Place the direction of rotation selector in center position.This will turn off the power to your drill. ■ Loosen the chuck jaws from drill bit . ■ To loosen: grasp and hold the collar of the chuck withone hand, wh...

Page 12 - CHUCK REMOVAL; TO RETIGHTEN A LOOSE CHUCK

Page 12 2 4 6 8 10 OPERATION Fig. 12 CHUCK REMOVAL See Figures 12, 13, and 14. ■ Lock the switch trigger by placing the direction of rotationselector in center position. ■ Insert a 5/16 inch or larger hex key wrench into the chuckof your drill and tighten the chuck jaws securely. ■ Tap the hex key w...

Page 13 - MAINTENANCE; BATTERIES

Page 13 MAINTENANCE WARNING: When servicing use only identical Ryobi replacementparts. Use of any other parts can create a hazard or causeproduct damage. Avoid using solvents when cleaning plastic parts. Mostplastics are susceptible to damage from various types ofcommercial solvents and may be damag...

Page 14 - • SERVICE; MODEL NUMBER

OPERATOR'S MANUALCORDLESS DRILL-DRIVERMODEL NO. HP1201M RYOBI TECHNOLOGIES INC. 1428 Pearman Dairy Road Anderson, SC 29625 Post Office Box 1207 Anderson, SC 29622-1207 Phone 1-800-525-2579 RYOBI TECHNOLOGIES INC. Post Office Box 910 Cambridge, Ontario N1R 6K2 Phone 1-800-265-6778 972000-758 8-00 • S...