Ryobi HD500- Manuals

Page 8 OPERATION INSTALLING AUXILIARY HANDLE (Continued) 4. Align tabs on depth gage clamp with slots in threadedhole in motor housing. NOTE: Depth gage clamp canbe rotated 180 ° so that depth gage rod will fit on either side of motor housing. 5. Carefully start the fine screw threads (#3/8-24) into...

Page 9 RIGHT OPERATION WARNING: Your hammer drill should never be connected to powers u p p l y w h e n y o u a r e a s s e m b l i n g p a r t s , m a k i n gadjustments, installing or removing drill bits, or when notin use. Disconnecting your drill will prevent accidentalstarting that could cause ...

Page 10 WARNING: Always wear safety goggles or safety glasses with sideshields when operating hammer drill. Failure to do socould result in dust, shavings, or loose particles beingthrown into your eyes, resulting in possible serious injury. DRILLING See Figure 11. 1. Depress and release the switch t...

Page 11 CHUCK REMOVAL CHUCK REMOVAL See Figures 12, 13, and 14. Whenever necessary to remove the chuck for replacement,etc., use the following procedure for chuck removal: 1. UNPLUG YOUR HAMMER DRILL. WARNING: Failure to unplug your hammer drill could result inaccidental starting causing serious inj...

Page 12 MAINTENANCE GENERAL Avoid using solvents when cleaning plastic parts. Most plas-tics are susceptible to damage from various types of commer-cial solvents and may be damaged by their use. Use cleancloths to remove dirt, carbon dust, etc. WARNING: Do not at any time let brake fluids, gasoline,...

972000-401 8-97 Printed In U.S.A. OWNER'S OPERATING MANUAL 1/2 in. (13 mm) Hammer Drill - HD500 DOUBLE INSULATED • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service,simply contact your nearest Ryobi Factory Service Center or Authorized Service Organi...

Page 8 OPERATION INSTALLING AUXILIARY HANDLE (Continued) 4. Align tabs on depth gage clamp with slots in threadedhole in motor housing. NOTE: Depth gage clamp canbe rotated 180 ° so that depth gage rod will fit on either side of motor housing. 5. Carefully start the fine screw threads (#3/8-24) into...

Page 9 RIGHT OPERATION WARNING: Your hammer drill should never be connected to powers u p p l y w h e n y o u a r e a s s e m b l i n g p a r t s , m a k i n gadjustments, installing or removing drill bits, or when notin use. Disconnecting your drill will prevent accidentalstarting that could cause ...

Page 10 WARNING: Always wear safety goggles or safety glasses with sideshields when operating hammer drill. Failure to do socould result in dust, shavings, or loose particles beingthrown into your eyes, resulting in possible serious injury. DRILLING See Figure 11. 1. Depress and release the switch t...

Page 11 CHUCK REMOVAL CHUCK REMOVAL See Figures 12, 13, and 14. Whenever necessary to remove the chuck for replacement,etc., use the following procedure for chuck removal: 1. UNPLUG YOUR HAMMER DRILL. WARNING: Failure to unplug your hammer drill could result inaccidental starting causing serious inj...

Page 12 MAINTENANCE GENERAL Avoid using solvents when cleaning plastic parts. Most plas-tics are susceptible to damage from various types of commer-cial solvents and may be damaged by their use. Use cleancloths to remove dirt, carbon dust, etc. WARNING: Do not at any time let brake fluids, gasoline,...

972000-401 8-97 Printed In U.S.A. OWNER'S OPERATING MANUAL 1/2 in. (13 mm) Hammer Drill - HD500 DOUBLE INSULATED • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service,simply contact your nearest Ryobi Factory Service Center or Authorized Service Organi...