Ryobi D41K- Manuals

− English Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper inter-pretation of these symbols will allow you to operate the product better and safer. Read The Operator’s Manual Safety Alert No Hands Symbol No Hands Symbol No Hands Symbol No H...

− English SyMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servic-ing, use only identical replacement parts. WARNING: T...

− English EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the...

− English FEATURES PRODUCT SPECIFICATIONS Chuck Capacity ....................................... 1/16 in. to 3/8 in. Switch ............................. VSR ( Variable Speed Reversible) No Load Speed .................................0-1,600 r/min. (RPM)Input ...................................... 1...

− English WARNING: If any parts are damaged or missing do not operate this product until the parts are replaced. Failure to heed this warning could result in serious personal injury. WARNING: Do not attempt to modify this product or create acces-sories not recommended for use with this product. Any ...

10 − English INSTALLING BITS See Figure 3 - 4.  Unplug the drill.  Open or close the chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws.  Insert the drill ...

11 − English uNlOck (ReleAse) DRIll B IT chuck JAWs chuck BODy lOck (TIGhTeN) RIGhT chuck cOllAR OPERATION WRONG REMOVING BITS See Figure 3.  Unplug the drill.  Rotate the chuck sleeve clockwise to open the chuck jaws. NOTE: Rotate the chuck body in the direction of the ar- row marked UNLOCK to lo...

1 − English OPERATION leVel leVel DRILLING See Figure 6 - 7. Levels are located on the top and end of the motor housing to help keep the drill bit level during use.  Depress and release the switch trigger to be sure the drill is in the OFF position before connecting it to a power supply.  Check th...

1 − English WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a ...

1 − English MAINTENANCE CHUCK REMOVAL See Figure 8. The chuck may be removed and replaced with a new one.  Unplug the drill.  Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely.  Tap sharply with a mallet in a counterclockwise direction. This will ...

983000-809-1-0 (REV:0) D41 • PaRts and sERVicE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate. • MOdEL nUMBER ____________________ • sERiaL nUMBER ____________________ • HOw tO OBtain REPLacEMEnt PaRts: Replacement ...

− English Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper inter-pretation of these symbols will allow you to operate the product better and safer. Read The Operator’s Manual Safety Alert No Hands Symbol No Hands Symbol No Hands Symbol No H...

− English SyMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servic-ing, use only identical replacement parts. WARNING: T...

− English EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the...

− English FEATURES PRODUCT SPECIFICATIONS Chuck Capacity ....................................... 1/16 in. to 3/8 in. Switch ............................. VSR ( Variable Speed Reversible) No Load Speed .................................0-1,600 r/min. (RPM)Input ...................................... 1...

− English WARNING: If any parts are damaged or missing do not operate this product until the parts are replaced. Failure to heed this warning could result in serious personal injury. WARNING: Do not attempt to modify this product or create acces-sories not recommended for use with this product. Any ...

10 − English INSTALLING BITS See Figure 3 - 4.  Unplug the drill.  Open or close the chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws.  Insert the drill ...

11 − English uNlOck (ReleAse) DRIll B IT chuck JAWs chuck BODy lOck (TIGhTeN) RIGhT chuck cOllAR OPERATION WRONG REMOVING BITS See Figure 3.  Unplug the drill.  Rotate the chuck sleeve clockwise to open the chuck jaws. NOTE: Rotate the chuck body in the direction of the ar- row marked UNLOCK to lo...

1 − English OPERATION leVel leVel DRILLING See Figure 6 - 7. Levels are located on the top and end of the motor housing to help keep the drill bit level during use.  Depress and release the switch trigger to be sure the drill is in the OFF position before connecting it to a power supply.  Check th...

1 − English WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a ...

1 − English MAINTENANCE CHUCK REMOVAL See Figure 8. The chuck may be removed and replaced with a new one.  Unplug the drill.  Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely.  Tap sharply with a mallet in a counterclockwise direction. This will ...

983000-809-1-0 (REV:0) D41 • PaRts and sERVicE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate. • MOdEL nUMBER ____________________ • sERiaL nUMBER ____________________ • HOw tO OBtain REPLacEMEnt PaRts: Replacement ...