Ryobi D40- Manuals

5 SAVE THESE INSTRUCTIONS SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION The purpose of safety symbols...

6 KNOW YOUR DRILL-DRIVER See Figure 1. Before attempting to operate your drill, familiarize yourselfwith all operating features and safety requirements. WARNING: Carefully read through this entire operator's manualbefore using your new drill. Pay close attention to theSafety Rules, Warnings and Caut...

7 FEATURES PRODUCT SPECIFICATIONS: DRILL-DRIVER D40 Chuck Capacity 1/16 in. to 3/8 in. (1.6 mm to 10 mm) Rating 120 V, 60 Hz, AC only Input 4.5 Amperes Switch Variable Speed No Load Speed 0-1400 RPM APPLICATIONS (Use only for the purpose listed below) ■ Drilling in wood. ■ Drilling in ceramics, plas...

8 OPERATION REVERSIBLE See Figure 3. FORWARD Fig. 3 REVERSE This tool has the feature of being reversible. Thedirection of rotation is controlled by a selector locatedabove the switch trigger. With the drill held in normaloperating position, the direction of rotation selectorshould be positioned to ...

9 OPERATION WARNING: Make sure to insert drill bit straight into chuck jaws.Do not insert drill bit into chuck jaws at an angle andthen tighten, as shown in Figure 5. This could causedrill bit to be thrown from drill, resulting in possibleserious personal injury or damage to the chuck. REMOVING BITS...

10 OPERATION LEVEL DRILLING See Figures 6 and 7. Two levels are recessed in the motor housing of yourdrill. One is located on top, while the other is locatedon the end. They can be used to keep drill bits levelduring both horizontal and vertical drilling operations. Fig. 7 LEVEL Fig. 6 LEVEL CHUCK R...

11 MAINTENANCE GENERAL All parts represent an important part of the doubleinsulation system and should be serviced only at anauthorized service center. Avoid using solvents when cleaning plastic parts. Mostplastics are susceptible to damage from various typesof commercial solvents and may be damaged...

13 RYOBI 3/8 in. DRILL-DRIVER – MODEL NO. D40 The model number will be found on a plate attached to the motor housing. Always mention themodel number in all correspondence regarding your 3/8 in. DRILL-DRIVER or when ordering parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Key No. Par...

983000-032 OPERATOR'S MANUAL3/8 in. (10 mm) Drill-DriverModel No. D40 DOUBLE INSULATED • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts orservice, simply contact your nearest Ryobi Authorized Service Center. Be sure toprovide all pertinent facts when you cal...

5 SAVE THESE INSTRUCTIONS SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION The purpose of safety symbols...

6 KNOW YOUR DRILL-DRIVER See Figure 1. Before attempting to operate your drill, familiarize yourselfwith all operating features and safety requirements. WARNING: Carefully read through this entire operator's manualbefore using your new drill. Pay close attention to theSafety Rules, Warnings and Caut...

7 FEATURES PRODUCT SPECIFICATIONS: DRILL-DRIVER D40 Chuck Capacity 1/16 in. to 3/8 in. (1.6 mm to 10 mm) Rating 120 V, 60 Hz, AC only Input 4.5 Amperes Switch Variable Speed No Load Speed 0-1400 RPM APPLICATIONS (Use only for the purpose listed below) ■ Drilling in wood. ■ Drilling in ceramics, plas...

8 OPERATION REVERSIBLE See Figure 3. FORWARD Fig. 3 REVERSE This tool has the feature of being reversible. Thedirection of rotation is controlled by a selector locatedabove the switch trigger. With the drill held in normaloperating position, the direction of rotation selectorshould be positioned to ...

9 OPERATION WARNING: Make sure to insert drill bit straight into chuck jaws.Do not insert drill bit into chuck jaws at an angle andthen tighten, as shown in Figure 5. This could causedrill bit to be thrown from drill, resulting in possibleserious personal injury or damage to the chuck. REMOVING BITS...

10 OPERATION LEVEL DRILLING See Figures 6 and 7. Two levels are recessed in the motor housing of yourdrill. One is located on top, while the other is locatedon the end. They can be used to keep drill bits levelduring both horizontal and vertical drilling operations. Fig. 7 LEVEL Fig. 6 LEVEL CHUCK R...

11 MAINTENANCE GENERAL All parts represent an important part of the doubleinsulation system and should be serviced only at anauthorized service center. Avoid using solvents when cleaning plastic parts. Mostplastics are susceptible to damage from various typesof commercial solvents and may be damaged...

13 RYOBI 3/8 in. DRILL-DRIVER – MODEL NO. D40 The model number will be found on a plate attached to the motor housing. Always mention themodel number in all correspondence regarding your 3/8 in. DRILL-DRIVER or when ordering parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Key No. Par...

983000-032 OPERATOR'S MANUAL3/8 in. (10 mm) Drill-DriverModel No. D40 DOUBLE INSULATED • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts orservice, simply contact your nearest Ryobi Authorized Service Center. Be sure toprovide all pertinent facts when you cal...