Ryobi CSB133L- Manuals

7 SyMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servic-ing, use only identical replacement parts. WARNING: To avoid ...

8 EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the char...

9 FEATURES PRODUCT SPECIFICATIONS  Blade Diameter ................................................. 7-1/4 in.  Blade Arbor ...........................................................5/8 in.  Cutting Depth at 0° ........................................... -3/8 in.  Cutting Depth at 45° .............

11 ASSEMBLy ATTACHING BLADE See Figures 2 - 4.  Unplug the saw.   Depress and hold spindle lock button.  Remove blade screw by turning it counterclockwise with the blade wrench, while keeping the spindle lock button depressed.  Remove spring washer and outer blade washer (“D” washer).  Wipe a ...

1 WARNING: Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in obje...

13 OPERATION   Inspect the workpiece for knots or nails before cutting. Never saw into a knot or nail.  Make straight cuts. Always use a straight edge guide when rip cutting. This helps prevent twisting the blade.  Use clean, sharp, and properly set blades. Never make cuts with dull blades.  Su...

14 OPERATION If at any time the lower blade guard does not snap closed, unplug the saw from the power supply. Exercise the lower guard by moving it rapidly back and forth from the full open position to the closed position several times. Normally this will restore the guard to its normal operating co...

15 OPERATION USING THE LASER GUIDES See Figure 12. WARNING: Do not stare into the laser beams or turn the lasers on when the tool is not in use. Failure to heed this warning could result in possible serious personal injury. The laser guide will generate a red laser beam on the work surface in front ...

16 OPERATION OPERATING THE SAW See Figures 13 - 15. It is important to understand the correct method for operat-ing the saw. Refer to the figures in this section to learn the correct and incorrect ways for handling the saw. WARNING: To make sawing easier and safer, always maintain proper control of ...

17 OPERATION LENGTH OF CUT SCALE See Figure 16. The saw is equipped with a length of cut scale on its base. It is parallel with the saw blade and can be used to measure the distance into the material the blade cuts. NOTE: Six inches is the maximum length of cut that you can measure. Also, it is accu...

18 OPERATION WARNING: Attempting a bevel cut without having the bevel ad-justment knob securely tightened can result in serious injury. TO BEVEL CUT See Figure 21.  Hold the saw firmly with both hands as shown.  Rest the front edge of the base on the workpiece.  Start the saw and let the blade re...

19 OPERATION 45 51.5 30 15 Fig. POCKeT CUT LOwer BLaDe GUarD LOwer BLaDe GUarD HaNDLe POCkET CUTTING See Figure 22. WARNING: Always adjust bevel setting to zero before making a pocket cut. Attempting a pocket cut at any other setting can result in loss of control of the saw possibly causing serious ...

0 Fig. 3 BeVeL aDJUSTMeNT KNOB BLaDe COMBINaTION SQUare aDJUSTING SCrew Hex NUT 0° BeVeL STOP 51.5 15 30 45 OPERATION 0° BEVEL STOP See Figure 23. The saw has a 0° bevel stop that has been factory adjusted to assure 0° angle of the saw blade when making 90° cuts.To check 0° bevel stop:  Unplug the ...

1 OPERATION OPTIONAL EDGE GUIDE See Figure 24. Use the optional edge guide, part no. 96986009, when making long or wide rip cuts with the saw. To assemble edge guide:  Unplug the saw.  Place edge guide through holes in base as shown in the figure.  Adjust edge guide to the width needed.  Tighten...

aDJUSTING SCrew Fig. 7 LaSer BarreL Fig. 8 LaSer BarreL ADJUSTMENTS WARNING: Before performing any adjustment, make sure the product is unplugged from the power supply and the switch is in the OFF position. Failure to heed this warning could result in serious personal injury. WARNING: DO NOT point t...

3 MAINTENANCE Electric tools used on fiberglass material, wallboard, spack-ling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommen...

CSB133L OPERATOR’S MANUAL 7-1/4 in. LASER CIRCULAR SAWDOUBLE INSULATED CSB133L 987000-374-1-08 (REV:00) • PARTS AND SERVICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate. • MODEL NUMBER • SERIAL NUMBER • HOW TO OBT...